HISTORY INFORMATION FOR THE FOLLOWING MANUAL: WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-32XBR4 RM-YD014 US/CANADA KDL-40D3000 RM-YD014 US/CANADA ORIGINAL MANUAL ISSUE DATE: 5/2007 REVISION DATE SUBJECT 5/2007 No revisions or updates are applicable at this time. 9/2007 Corrected note under BH Board.
Page 2
Self Diagnosis Supported model WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-32XBR4 RM-YD014 US/CANADA KDL-40D3000 RM-YD014 US/CANADA KDL-40D3000 RM-YD014 LCD DIGITAL COLOR TELEVISION 9-883-751-02...
Trademark Information “BRAVIA” and , S-Force, BRAVIA Theatre Sync, and DMe trademarks or registered marks of Sony Corporation. Blu-ray Disc is a trademark. “XMB”, “XrossMediaBar” and “PS3” are trademarks of Sony Corporation and/or Sony Computer Entertainment Inc. This TV incorporates High-Definition Multimedia Interface (HDMI™) technology.
Page 5
Headphones Plug Adapter Connecting Cables Panel System Wall-Mount Bracket LCD (Liquid Crystal Display) Panel SU-WL500 TV Stand Display Resolution (horizontal x vertical): RHT-G800 1,366 dots x 768 lines Screen Size (measured diagonally) 31.5 inches (KDL-32XBR4 Only) 40 inches (KDL-40D3000 Only) KDL-32XBR4/40D3000...
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony.
KDL-32XBR4/40D3000 SAFETY-RELATED COMPONENT WARNING There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi...
Page 8
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com KDL-32XBR4/40D3000...
KDL-32XBR4/40D3000 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KDL-32XBR4/40D3000 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED indicator will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 11
KDL-32XBR4/40D3000 Viewing the Self Check Diagnostic List 1. TV must be in standby mode. (Power off). 2. Press the following buttons on the Remote Commander within a second of each other: Channel 5 Volume - TV POWER . DISPLAY The Self Check list displays.
KDL-32XBR4/40D3000 1-3. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL (KDL-32XBR4 ONLY) Remove 2 screws from bottom of Arms, +PSW M5X16 Remove 3 screws from bottom bracket and Stand, +PSW M5X16 VESA Arm Assembly Stand Assembly Under Cover Bottom Bracket 1-4. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL...
KDL-32XBR4/40D3000 1-5. U2 BOARD, DTT SHIELD, AND JACK HOLDER REMOVAL Disconnect two connectors Remove three screws, +BVTP 3X12 TYPE2 IT-3 U2 Board Release hooks and remove U2 Board Remove Jack holder from Bezel. Release hooks to remove DTT Shield from BU2 bottom shield.
KDL-32XBR4/40D3000 1-14. LCD PANEL, LED AND GUIDE LIGHT REMOVAL (KDL-40D3000 ONLY) Remove 2 screws from Bezel and Top Brackets, +BVTP2 4X16 Remove 4 screws from Top Brackets, +PSW M5X8 Remove 4 screws from Bottom Brackets, + PSW M5X12 Remove 4 screws from Stand Holders, +PSW M5X16...
KDL-32XBR4/40D3000 1-15. INVERTER BOARD REMOVAL CAUTION: Be sure to identify the inverter cover screws before proceeding. DO NOT remove the screws securing the plastic strip holding the lamp sockets. Remove screws securing the inverter cover. Remove screws securing the inverter board...
KDL-32XBR4/40D3000 WIRE DRESSING KDL-32XBR4 ONLY OVERALL VIEW KDL-32XBR4/40D3000...
Page 23
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. 2. Use ribs on bezel (w/o screw boss) as a guide to center tape. Make sure Cushion D is Centered over the H3 Harness.
Page 24
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H3 BOARD HARNESS (CONTINUED) OPERATION PROCESS Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use ribs on bezel (w/o screw boss) as a guide to center tape. Make sure Sheet Core C is Use Bottom of UL Tape to align Sheet Core C.
Page 25
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H3 BOARD HARNESS (CONTINUED) OPERATION PROCESS Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use ribs on bezel (w/o screw boss) as a guide to center tape. Apply LCD Tape to hold BOTH Rt.
Page 26
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H4 BOARD OPERATION PROCESS 1. Install H4-Bd BEFORE Installing the speakers/baffles. 2. Apply LCD Tape on SIDE of the magnet on Rt. Speaker to hold the H4 Cables. 3. MAKE SURE there is slack in the cable between the H4 Connector and LCD Tape.
Page 27
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Dress BOTH H4/Speaker Cables in plastic clips on G-Bracket. Wire Dress Rt. Speaker wires and H4 cables in G-Bracket clips. NOTE: Speaker cables are NOT dressed inside NOTE: Rt. Spkr. Wires are NOT dressed far left clip on G-Bracket.
Page 28
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H4 BOARD AND RIGHT SPEAKER (CONTINUED) OPERATION PROCESS 1. Wire Dress Right Speaker wires and H4 NOTE BOTH H4-Bd and Rt. Speaker cables in side clamps (white) and G3-Bd cables are dressed UNDER AC Inlet bracket clips (black).
Page 29
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. DRESS CABLES 1st DRESS CABLES LAST ON TOP ALL CABLES. DRESS CABLES 3rd...
Page 30
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS Route/Dress Core-Block cables as shown Put Attention on DIRECTION of cables in G-Bracket. Put Attention on the position of the Side Clamps and routing of the Cables between Core Block and G1-Bracket.
Page 31
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY G1H BOARD OPERATION PROCESS 1. Install/Wire Dress Harnesses as shown. 2. CAUTION: Make sure INVERTER CONNECTOR is Fully LOCKED!! G-Bd NOTE: NEW G-Bracket Change! Inverter wire is NOT dressed in 1st clip. Inverter wires are dressed in cut-out on...
Page 32
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY SPEAKER HARNESS OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. Use UL Tape to align Cables in clip. FGC-3 CLAMP ELIMINATED 2. Apply LCD TAPE to BOTH H4-Bd AND Right speaker Wires. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm)
Page 33
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY SPEAKER HARNESS (CONTINUED) OPERATION PROCESS LVDS Wire and Speaker Wire cannot touch. Wire Dress Speaker Cables as shown. (NG for EMI). Use UL Tape to align Cables in clip. BOTH R/L cables are dressed in FGC-3 Route Wires Away from metal Tab conductive clip.
Page 34
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS 1. Dress LEFT speaker harness as shown Dress Lt. Speaker wires in Sheet Core C. Lt. Speaker cables should only cross Route Wires on TOP of Panel Edge away over top of Panel edge once in this from sharp edge.
Page 35
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY U2 BOARD OPERATION PROCESS 1. Apply TAPE, U2 to Panel in location where U2 bracket is to be installed (Use edges of panel as guide) 2. Make sure DTT Shield has Sheet Core C installed as per diagram.
Page 36
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY H1 BOARD OPERATION PROCESS 1. Dress/Route H1-Bd harness as shown on photo. 2. NOTE: Put attention on SLACK of cable. Between Connector on H1 and tape there is slack in wire. Between tape/clamp there is slack. Plastic Side Clamp.
Page 37
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY LVDS CABLE - BU BOARD TO BH BOARD OPERATION PROCESS 1. Attach HDMI Connector to BU-Bd (CN5502). 2. GENTLY fold over cables to right side. Install HDMI Cable on BU-Bd 3 CONFIRM Color of Sticker (RED) (CN5504) NOTE: COLOR OF Round 4.
Page 38
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY LVDS CABLE - BH BOARD TO TCON OPERATION PROCESS 1. Route 40P LVDS Cable between BU-Bd and TCON as shown. NOTE: LVDS Cable is OVER ALL cables 2. Apply 3x8mm Screw (2-places) to ground LVDS cable. Put Attention on Routing of Cable.
Page 39
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY LVDS CABLE - BU BOARD OPERATION PROCESS O.K. ! 1. Route 40P LVDS Cable between BU-Bd and TCON as shown. CAUTION: 2. Apply 3x8mm Screw to BH Shield Top. DO NOT allow TCON END of cable to...
Page 40
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY HDMI CABLE OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC. KDL-32XBR4/40D3000...
Page 41
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS USE SCREW on panel as reference USE plastic clip on panel as guide for corner of Sheet Core C installation. for corner of Sheet Core C installation Route/Dress HDMI Cables as shown.
Page 42
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS USE Sheet Core C to hold LVDS to panel here Route/Dress HDMI Cables as shown. Center conductive tape over Black UL tape on LVDS (last black tape on harness). CAUTION: Make sure HDMI cable is touching panel, especially in between Sheet Core C.
Page 43
KDL-32XBR4/40D3000 KDL-32XBR4 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS 1. Connect HDMI Cable Assy to U2-Bd. As shown. 2. Install 3x5mm Screw Install 3x5mm screw to GND Tab TORQUE SPECIFICATION on HDMI Cable Assy. TORQUE: 6.0kg.cm (+-1.0kg.cm) NOTE: SIDE HDMI Cable may have conductive tape wrapping, however, new process eliminates tape.
KDL-32XBR4/40D3000 KDL-40D3000 ONLY OVERALL VIEW KDL-32XBR4/40D3000...
Page 45
KDL-32XBR4/40D3000 KDL-40D3000 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use rib on bezel (w/o screw boss) as a guide for mid-point of tape. Use split in harness(H4 wires) and UL tape as reference for Harness positioning.
Page 46
KDL-32XBR4/40D3000 KDL-40D3000 ONLY H3 BOARD HARNESS (CONTINUED) OPERATION PROCESS 1. Apply Sheet Core C as Shown on H3-Bd Harness 2. Wire Dress AC INLET As shown. MAKE SURE TO install EARTH GROUND SCREW on Green/Yellow Earth Wire. Dress AC Inlet Cables In G3 Bracket clamps.
Page 47
KDL-32XBR4/40D3000 KDL-40D3000 ONLY H4 BOARD OPERATION PROCESS 1. LED Guide and Screw is pre-assembled by Vendor. 2. Install H4-Bd. Be careful to align Plastic clip at bottom of bezel with notch in PWB. 3. Use x1 3x12mm screw to fix H3-Bd to Bezel.
Page 48
KDL-32XBR4/40D3000 KDL-40D3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Wire Dress Right Speaker wires and H4 cables in side clamps (white) and G3-Bd bracket clips (black). 2nd UL Tape indicates SPLIT for H3-Bd / H4-Bd cables. NOTE: H4 cables are ABOVE Himelon tape.
Page 49
KDL-32XBR4/40D3000 KDL-40D3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. Keep Cables BELOW level of Shield Case (Pinch Points) NOTE order and direction of cables!
Page 50
KDL-32XBR4/40D3000 KDL-40D3000 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS Apply Sheet Core C tape as shown. Align Sheet Core C with Center of BH Shield Case and clips on G3 Bracket. KDL-32XBR4/40D3000...
Page 51
KDL-32XBR4/40D3000 KDL-40D3000 ONLY G3 BOARD AND D1 BOARD OPERATION PROCESS Install/Wire Dress Harnesses as shown. CAUTION: BE CAREFUL which connector is used on G3-Bd for Installing harness with ferrite core (CN6502 on G3-Bd). NOTE: Ferrite core not used in final design...
Page 52
KDL-32XBR4/40D3000 KDL-40D3000 ONLY G3 BOARD AND D1 BOARD (CONTINUED) OPERATION PROCESS Install / Wire Dress Harnesses as shown. "Cross" (as shown on photo). KDL-32XBR4/40D3000...
Page 53
KDL-32XBR4/40D3000 KDL-40D3000 ONLY INVERTER BOARD AND D1 BOARD OPERATION PROCESS INVERTER INVERTER CAUTION MAKE SURE BLACK INSULATION O.K. N.G. TUBING DOES NOT TOUCH CONN BEFORE INSTALLING 2P MD CONN. AFTER INSTALLING CONNECTOR, TUBE INSULATION CAN TOUCH CONNECTOR! INSTALL INVERTER SIDE 1ST INSTALL D1-Bd SIDE 2ND O.K.
Page 54
KDL-32XBR4/40D3000 KDL-40D3000 ONLY INVERTER BOARD AND D1 BOARD (CONTINUED) OPERATION PROCESS CAUTION: MAKE SURE WHITE/PINK WIRES DO NOT CROSS CHECK INVERTER SIDE WIRES CHECK D1-Bd SIDE WIRES INVERTE CAUTION: Make Sure Inverter Connector DOES NOT CROSS WHITE/PINK WIRES! CHECK BOTH SIDES OF HARNESS!
Page 55
KDL-32XBR4/40D3000 KDL-40D3000 ONLY G3 BOARD AND D1 BOARD OPERATION PROCESS NOTE: Ferrite Core and Sheet Core A Install/Wire Dress Harnesses as shown. Applied by SBC Plants. UPDATE: CAUTION: Make sure INVERTER CONN. 4/13/2007: FERRITE/Sheet Core is Fully LOCKED!! Not used in final design...
Page 56
KDL-32XBR4/40D3000 KDL-40D3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION OPERATION PROCESS MAKE SURE COLOR of UL tape is the correct color (YELLOW) for harness. Confirm wires are dressed properly in clips. Confirm 2P BD Connectors are FULLY LOCKED by pressing on BOTH locking tabs (RED ARROWS).
Page 57
KDL-32XBR4/40D3000 KDL-40D3000 ONLY SPEAKER CABLES OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. LEFT Speaker cable is dressed in side clamp (white plastic). 2. BOTH R/L cables are dressed in FGC-3 conductive clip. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm) NOTE:...
Page 58
KDL-32XBR4/40D3000 KDL-40D3000 ONLY SPEAKER CABLES (CONTINUED) OPERATION PROCESS LVDS Wire and Speaker Wire cannot touch. Wire Dress Speaker Cables as shown. (NG for EMI). Use UL Tape to align Cables in clip. Route Wires Away from metal Tab BOTH R/L cables are dressed in FGC-3 (sharp edge) conductive clip.
Page 59
KDL-32XBR4/40D3000 KDL-40D3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS Dress LEFT speaker harness as shown Side HDMI LVDS cable will be shorter NOTE: Install Sheet Core C as in length for PRE-PRO and MASS-PRO shown in photo. Side HDMI LVDS Cable is dressed in same Sheet Core C as shown.
Page 60
KDL-32XBR4/40D3000 KDL-40D3000 ONLY U2 BOARD OPERATION PROCESS 1. Apply Sheet Tape H2 to Panel in location where U2 bracket is to be installed (Use plastic ribs on bezel as guide) 2. Make sure DTT Shield has Sheet Core C installed as per diagram.
Page 61
KDL-32XBR4/40D3000 KDL-40D3000 ONLY H1 BOARD OPERATION PROCESS Dress/Route H1-Bd harness as shown "Cross" (as shown on photo). NOTE which connector cables are attached to NOTE: Put attention on SLACK of cable. on H1-Bd. Between Connector on H1 and tape there is slack in wire.
Page 62
KDL-32XBR4/40D3000 KDL-40D3000 ONLY LVDS CABLE - BU BOARD TO BH BOARD OPERATION PROCESS Route 40P LVDS Cable between BH-Bd and BU-Bd as shown. NOTE COLOR of the UL Tape on the BH-Bd side. Correct color is RED. NOTE COLOR of the UL Tape (RED)
Page 63
KDL-32XBR4/40D3000 KDL-40D3000 ONLY LVDS CABLE - BU BOARD TO BH BOARD (CONTINUED) OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC.
Page 64
KDL-32XBR4/40D3000 KDL-40D3000 ONLY LVDS CABLE - BH BOARD TO TCON OPERATION PROCESS Route/Dress LVDS cable between BH-Bd and TCON as shown. NOTE: Put Attention on Cable routing. LVDS cable must be PARALLEL to Panel Surface (see photos). NOTE COLOR of the Shrink Tubing (BLACK).
Page 65
KDL-32XBR4/40D3000 KDL-40D3000 ONLY HDMI CABLE OPERATION PROCESS 1. Attach HDMI Connector to BU-Bd (CN5504). 2. GENTLY fold over cables to right side. 3 CONFIRM Color of Sticker (BLUE) Install HDMI Cable on BU-Bd 4. After Installing DTT Top apply 3x5mm (CN5504) screw to GND Ring on HDMI Assy.
Page 66
KDL-32XBR4/40D3000 KDL-40D3000 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS Route/Dress HDMI Cables as shown. CAUTION: Make sure HDMI cable is touching panel, especially in between Sheet Core C. CAUTION: Make sure HDMI Cable is touching panel (length will be fixed for Pre-Pro)
Page 67
KDL-32XBR4/40D3000 KDL-40D3000 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS USE Sheet Core C to hold LVDS/Left Speaker Wire to panel here Route/Dress HDMI Cables as shown. Center conductive tape over Black UL tape on LVDS (last black tape on CAUTION: Make sure HDMI cable is harness).
Page 68
KDL-32XBR4/40D3000 KDL-40D3000 ONLY HDMI CABLE (CONTINUED) OPERATION PROCESS 1. Connect HDMI Cable Assy to U2-Bd. As shown. 2. Install 3x5mm Screw Install 3x5mm screw with TORQUE SPECIFICATION washer to GND Tab on HDMI Cable Assy. TORQUE: 6.0kg.cm (+-1.0kg.cm) NOTE: SIDE HDMI Cable may have conductive tape wrapping, however, new process eliminates tape.
KDL-32XBR4/40D3000 SECTION 2: SERVICE ADJUSTMENTS 2-1. USING THE REMOTE COMMANDER 2-3. VIEWING THE SERVICE MENUS FOR ELECTRICAL ADJUSTMENTS Use the Remote Commander to view the BE and Digital service menus options. To adjust various set features, use the Remote Commander to put the set into service mode to display the service menus and categories.
KDL-32XBR4/40D3000 2-4. USING THE REMOTE COMMANDER TO 1. Access Service Adjustment Mode and select the Service Menu that contains the Category with the Adjustment Item you want to change. VIEW SERVICE DATA 2. To change the Category, press 2 or 5 on the Remote Commander.
KDL-32XBR4/40D3000 2-5. VERIFYING SERVICE DATA CHANGES 1. After completing all adjustments turn the set off with the Remote Commander and then proceed to the next step. 2. Press the following buttons on the Remote Commander within a second of each other:...
KDL-32XBR4/40D3000 3-2. PRINTED WIRING BOARDS AND Terminal name of semiconductors in silk screen SCHEMATIC DIAGRAMS INFORMATION printed circuit ( All capacitors are in μF unless otherwise noted. pF : μμF 50WV or Circuit Device Printed symbol Terminal name Collector less are not indicated except for electrolytics and tantalums.
KDL-32XBR4/40D3000 BU2 BOARD SCHEMATIC DIAGRAM (4 OF 12) JL 4508 TMDS_RX0- Y_G1 R X 0- TO HDMI JL 4509 TMDS_RX0+ PB_B1 RX0+ JL 4510 •¡ SV P-PX P DDR & CPU I/F, POWE R & GND PB_R1 TMDS_RX1- — R X 1-...
KDL-32XBR4/40D3000 BU2 BOARD SCHEMATIC DIAGRAM (9 OF 12) X IL L EON242 GROUND BAL L S ASIC CORE POWER D2.5V _A T I D1.0V D3.3V _A T I COR E _1.0V (NE E D <50mV NOI SE ) — FB 7200...
KDL-32XBR4/40D3000 G1H BOARD SCHEMATIC DIAGRAM (POWER SUPPLY) (KDL-32XBR4 ONLY) This board is manufactured by a 3rd party. Component level repair information is not available. [POWER SUPPLY] PWB IS NOT AVAILABLE KDL-32XBR4/40D3000...
KDL-32XBR4/40D3000 H1 BOARD SCHEMATIC DIAGRAM POWER — H1 BOARD S101 USER CONTROL — HOME INPUT SEL VOL+ VOL- MENU TO BU2 WEGAGATE POWER INT CN3008 KEY1 — R107 R102 CN101 S104 S107 S106 S105 S103 S102 — R104 R101 R105 R103 1 .
Page 97
KDL-32XBR4/40D3000 [USER CONTROL] COMPONENT SIDE VOL+ R102 S104 VOL- VIA G[CV OK S105 R103 INPUT SEL S103 R108 S106 R101 R107 S107 R104 S101 POWER S102 HOME 1-872-981-11 A-1220- MENU C103 (172841011) WEGAGATE [USER CONTROL] CONDUCTOR SIDE CN102 CN101 JL101...
REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] (Please review the Sony Electronics Service Information website for any additional service information.) X-2179-398-1 COVER ASSEMBLY, REAR (40) A-1259-944-A STAND (M_WS)ASSEMBLY [7-8] (KDL-40D3000 ONLY) (KDL-32XBR4 ONLY)
See Appendix A: Encryption Key Components in the back of this manual. 4-2. CHASSIS (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-580-629-01...
See Appendix A: Encryption Key Components in the back of this manual. 4-3. BEZEL ASSEMBLY AND LCD PANEL (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 REF. NO.
See Appendix A: Encryption Key Components in the back of this manual. 4-4. CONNECTORS (KDL-32XBR4 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF.
See Appendix A: Encryption Key Components in the back of this manual. 4-5. CONNECTORS (KDL-40D3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF.
See Appendix A: Encryption Key Components in the back of this manual. 4-6. SPEAKERS (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-580-600-01...
KDL-32XBR4/40D3000 SECTION 5: ELECTRICAL PARTS LIST Items marked with an asterisk are not stocked since they NOTE: The components identifi ed by shading are seldom required for routine service. Expect some delay mark are critical for safety. Replace only when ordering these components.
Page 120
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 121
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 122
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 123
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 124
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 134
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 135
0.50% 1/10W 1-474-052-12 G1H BOARD, COMPLETE (POWER UNIT) R6761 1-218-853-11 METAL CHIP 1.8K 0.50% 1/10W (KDL-32XBR4 ONLY) This board is manufactured by a 3rd party. Component level R6762 1-211-983-11 METAL CHIP 0.50% 1/10W repair information is not available. R6763 1-218-863-11 METAL CHIP 4.7K...
Page 136
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 137
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 138
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 139
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only G3 H1 que par une piece portant le numero specifi e.
Page 141
KDL-32XBR4/40D3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
MUST BE RETURNED to Sony. b) and if the core charge is NOT covered under the product warranty, the defective un-repaired or modified board MUST BE DESTROYED.
Page 144
In an effort to reduce the size of this pdf file the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.