Table of Contents
Advertisement
LTC 2600 Series | Instruction Manual | Multiplexer Set (MS) Commands
MS-AUTOSET <boolean> <boolean> <boolean>
<boolean> <boolean
This command carries out the autoset function for the
current setup for each of the following: record, video
loss, sequence, alarm, and action list respectively.
Parameter values are:
MS-CAM-AUTOCOLOR <auto-detect>
This command enables or disables the multiplexer
autocolor operation. When autocolor is enabled, the
system automatically enables color operation for any
color camera connected to the system (or added later).
When autocolor is disabled, the multiplexer will use
the results of the last autocolor detection to enable the
color operation of the cameras (unless an MS-CAM-
COLOR command is sent).
Parameter values for <auto-detect> are:
MS-CAM-COLOR <table 16>
This command allows the color operation of the
cameras connected to the system to be manually
selected.
NOTE: AUTOCOLOR is automatically disabled
whenever and MS-CAM-COLOR command is sent.
The <table 16> parameter ranges in value from <0> to
<65535> (decimal) OR <0> to <FFFF> (hex). Table
16 is a 16-position (bit) table where the value in each
position corresponds to the color operation of a
specific camera (i.e. a value of 1 enables color; a value
of 0 disables color).
EXAMPLE: To enable color on only cameras 1-4, a
value of <15> decimal (000F hex) is used in <table
16>.
Camera No.: 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Position (Bit) #:
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1-4 Enabled, Table Value 15: (000F hex)
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1
Bosch Security Systems | July 12, 2004
0
Disabled
1
Enabled
0
Disables Autocolor
1
Enables Autocolor
MS-CAM-FULL <monitor> <camera#>
This command assigns the specified camera to the
specified monitor if the monitor is in full screen mode.
NOTE: If the monitor is not is full screen mode, the
command has no effect.
Parameter values for <monitor> and <camera#> are:
<monitor>
1
2
<camera#>
1 to 16
MS-CAM-NUMBER <starting-number>
This command sets the starting camera number to be
displayed on the monitor when the camera connected
to rear panel camera input #1 is selected.
Parameter values for <starting-number> range from
<1> to <983>.
EXAMPLE: If you wanted to set 101 as the number to
be displayed on the monitor(s) when the camera
connected to rear panel camera input #1 is selected,
you would enter <101> as the value for <starting-
number>. The camera connected to rear panel camera
input #2 would then automatically be displayed as
camera 102, and so on.
MS-CAM-TITLE <camera#> <"text">
This command specifies a camera title to be displayed
on the monitor screen.
Parameter values for <camera#> and <"text"> are as
follows:
<camera#>
1 to 16
<"text">
Valid characters are: A to Z
(uppercase only), 0 to 9, space, * + , -
. / : [ ], 16 characters maximum (not
including double quotes which must
be used on either side of the text)
NOTE: Each camera's title is set individually. The
camera title entered must begin and end with double
quotation marks, as shown in the command syntax
(these marks will not be shown on the screen). If
lowercase characters are used, they will automatically
be converted to uppercase. Any illegal characters will
be replaced with a ":?".
EN | 14
Monitor A
Monitor B
Advertisement
Table of Contents
