Panasonic DMP-BD80 Operating Instructions Manual page 37
Blu-ray disc player
Hide thumbs
Also See for DMP-BD80:
- Operating instructions manual (48 pages) ,
- Service manual (7 pages) ,
- Operating instructions manual (52 pages)
Table of Contents
Advertisement
Changing the speaker setting to suit your speakers
B080
When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the
amplifier/receiver.
The settings are effective when connecting to analog 7.1ch/5.1ch AUDIO OUT terminal.
Center (C)
Difference
Setting
Approx. 34 cm (1 ft. 1 in.)
1.0 ms
Approx. 68 cm (2 ft. 2 in.)
2.0 ms
Approx. 102 cm (3 ft. 4 in.)
3.0 ms
Approx. 136 cm (4 ft. 5 in.)
4.0 ms
Approx. 170 cm (5 ft. 6 in.)
5.0 ms
Circle of constant primary listening distance
Q :
Actual speaker position
•
: Ideal speaker position
® ® © :
Primary listening distance
®
Center speaker
©
Surround/Surround back speakers
5.1ch speaker connection
7.1ch speaker connection
Approximate room dimensions
Difference
Setting
Approx. 170 em (5 ft. 6 in.)
5.0 ms
Approx. 340 em (11 ft. 1 in.)
10.0 ms
Approx. 510 em (16 ft. 8 in.)
15.0 ms
Channel balance
(~)
o
Select "Test" and press [OK).
A test signal is output.
Front
(L)~Center (C)~Front (R)~Surround
(RS)
t
t
Surround (LS)-- Surround Back (LB) __ Surround Back (RB)
e
While listening to the test signal, press
[A.
~]
to adjust the
volume of each speaker
Front speakers: 0.0 to -6.0 dB
Center and surround speakers: 0.0 to -12.0 dB
e
Press [OK).
The test signal stops.
-No signal is output for the subwoofer. To adjust its volume. play
something. then return to this screen to adjust to suit your taste.
Subwoofer (SW)
(LB) Surround back(RB)*
D
(LS) Surround (RS)
Front (L)
Complete
Test
----,.s-c.c.:o,
Large
-Large:
-Small:
~
Small
No
Select when the speaker supports low-frequency
(under 100 Hz) reproduction.
Select when the speaker does not support
low-frequency reproduction.
In order to make an ideal listening environment. settings of speaker
sizes may be automatically adjusted.
For example. if the subwoofer is set to "No". the front speakers will
automatically be set to "Large". (In this case. we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
Preparation
o
Set "Analog Audio Output" to "2ch (Downmix) + 5.1 ch" or "7.1 ch".
(~
34)
A message is displayed.
e
Press [OK).
* Surround back channel is enabled only when setting "Analog Audio
Output" to "7.1 ch".
Speaker presence and size (
~W!E~~~~
)
Set all the connected speakers individually.
o
Press [A,
~
.....
~)
to select the speaker icon and press [OK).
e
Press
[A.
~)
to select the setting and press [OK).
Icon examples:
Surround speaker (LS)
Delay time (
Iil)
For optimum listening with 7.1/5.1-channel sound. all the speakers,
except for the subwoofer. should be the same distance from the
seating position.
If you have to place the center, surround and surround back speakers
closer to the seating position. adjust the delay time to make up for the
difference.
If either distance
®
or
©
is less than
®
(~
right). find the difference
in the relevant table and change to the recommended setting.
o
Press
[A.
~
.....
~)
to select the delay time box (
iii)
and press
[OK).
e
Press [A.
~)
to select the setting and press [OK].
To finish the speaker setting
Press [A,
~
.....
~)
to select ·Complete" and press [OK).
RQT9378
Hide quick links:
Advertisement
Table of Contents
