Advertisement
Quick Links
Mounting Guide
Network Camera
BB-HCM547
Model No.
Please read the included Important Information before proceeding.
Complete Operating Instructions and all other documentation can be found on the included CD-ROM.
• This document (Mounting Guide) explains how to mount or place the camera
for regular use.
• The Installation Guide describes the items required for installation and how
to physically connect the camera to the power supply and network.
• The Setup Guide describes how to set up the camera so that it can be
accessed using a PC.
• Model number suffixes ("A" and "CE") are omitted from the following model
numbers shown in this document, unless necessary.
BB-HCM547A, BB-HCM547CE
Abbreviations
• The Network Camera is referred to as "the camera" in this document.
Important Information Regarding Camera Mounting
Please read the following information before mounting the camera. Consult an
authorized dealer for mounting.
Caution
• Make sure you attach the safety wire when mounting the camera on a
ceiling to prevent the camera from falling.
Note
• If you install the camera outdoors, the external microphone or speaker must
be outdoor compatible.
• Use screws that are appropriate for the material of ceiling.
• The included screws are for use with wooden ceilings only.
• Do not drive the screws into a soft material. Drive the screws into a secure,
25 mm (1 inch) thick area of the ceiling, such as a crossbeam, otherwise the
camera may fall. If there is no crossbeam, place a board on the other side
of the ceiling to make sure the camera is securely mounted.
• The pull-out strength of the installation area must be at least 294 N (30 kgf)
per screw.
• To ensure that camera images are displayed properly, mount the camera to
a flat horizontal surface.
• The ceiling mounting cover must be removed in order to insert or remove
the SD memory card.
• The camera's MAC address and serial number are printed on the bottom of
the camera and are needed in order for camera configuration and
maintenance. Make a note of both of them before mounting the camera.
• Mounting and cabling instructions described in this document follow
generally accepted guidelines suitable for residential installations. In some
areas, commercial and industrial installations are regulated by local or state
ordinances. For such installations, contact your local building department or
building inspector for more details.
• Camera images can be viewed in relatively dark areas, however, image
quality decreases when viewing dark images. We recommend using
supplemental lighting for best results.
• Prolonged exposure to direct sunlight or halogen light may damage the
camera's image sensor. Mount the camera appropriately.
• When mounting the camera, make sure to wrap the AC adaptor cord (if
used) around the hooks as shown to ensure secure connections.
Cable hook
• Mount the camera in a sheltered place where it is not directly exposed to
direct sunlight or the elements.
• Avoid installations where the camera can be exposed to air containing high
levels of salt, ammonia, sulfur etc. (Exposure to such conditions can reduce
the operating life of the camera)
• Do not directly touch the lens cover. Clean the lens cover with a dry and soft
cloth if necessary.
Mounting the Camera
Wiring through a hole made in the ceiling
1.
Place the base cover against the ceiling in the desired installation
location. Open a hole in the ceiling as shown in the mounting reference
diagram.
• The 45 mm (1 3/4 inches) area around the center of the hole should be
flat, and without any bumps or grooves.When the ceiling's surface is not
flat, waterproof the area between the base cover and the ceiling to
make sure there are no gaps between the holes.
© Panasonic System Networks Co., Ltd. 2008
PQQX16405YA KK0608CM1020
(PoE Ready)
Outdoor Ready
Under eaves installation
Please read this document before using the product, and save this document for future
reference. Panasonic Network Camera Website:
http://panasonic.net/pcc/ipcam/
• Refer to the Operating Instructions on the CD-ROM for details regarding
the camera's features.
• Refer to the Troubleshooting Guide on the CD-ROM if you have any
problems configuring or using the camera.
• The Stand-alone SD Memory Card Recording Guide describes how to
record images to an SD memory card without using a PC.
• The Setup CD-ROM is referred to as "the CD-ROM" in this document.
2.
Secure the base cover to the ceiling using screws C (included).
• Make sure there is at least 250 mm (9 13/16 inches) of space, with no
obstacles, from the center of the plate.
• Screws C are for use with wood-based installation areas. Use screws
appropriate for the material of the installation area.
Camera direction
3.
Connect all necessary cables (AC adaptor, LAN, audio/video, etc.).
• Pass the cables through the hole on the ceiling plate and connect them
to the camera.
4.
Align the two round protrusions on the camera and the holes on the
ceiling plate, and turn the screws A (included) to attach the ceiling plate
firmly. Attach the safety wire to the ceiling plate with screw B (included)
and washer B (included), as shown.
• Make sure you do not scratch the lens cover when performing this
procedure.
Screws A (2 pcs.) (Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Fit the two protrusions
in place.
<Bottom View>
Camera Direction
Base Cover
Necessary Installation
Range
Hole for wiring cables
Keep more than 250 mm (9 13/16 inches)
off the wall or other obstacles.
Screws C (3 pcs.)
(Length: 30 mm [1 3/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Screw B (Length: 8.0 mm [5/16 inches],
Body diameter: 3.0 mm [1/8 inches])
Washer B
(Inside diameter: 3.0 mm [1/8 inches])
Arrow on the ceiling plate
Camera's indicator
Advertisement
Related Manuals for Panasonic BB-HCM547
Summary of Contents for Panasonic BB-HCM547
-
Page 1: Mounting The Camera
Body diameter: 4.0 mm [3/16 inches]) (Inside diameter: 3.0 mm [1/8 inches]) make sure there are no gaps between the holes. Fit the two protrusions in place. Arrow on the ceiling plate Camera’s indicator <Bottom View> © Panasonic System Networks Co., Ltd. 2008 PQQX16405YA KK0608CM1020... - Page 2 Align the hooks on the base cover and the notches on the ceiling plate, Align the two round protrusions on the camera and the holes on the ceiling plate, and turn the screws A (included) to attach the ceiling plate turn the ceiling plate clockwise while pushing the camera into the base firmly.