Table of Contents
Advertisement
i Prohibited indicator (PROHIBITED)
This indicator (red) lights up for 3 seconds when an
attempt is made to gain access to a function that is pro-
hibited by the partition.
o Joystick Controller (UP / DOWN / L / R)
The joystick is used to manually operate the Pan / Tilt
Head, or move the cursor in the Camera Menu on the
active monitor screen.
UP:
Upward
DOWN:
Downward
L:
Left
R:
Right
!0 Iris buttons (IRIS, CLOSE / OPEN)
Closes or opens the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory default setting.
!1 Focus buttons (FOCUS, NEAR / FAR)
Adjusts the lens focus of cameras equipped with the
specified lens.
When these buttons are pressed at the same time, the
lens focus is set automatically if the specified camera
with the auto focus feature is equipped.
!2 Zoom buttons (ZOOM, WIDE / TELE)
These buttons are used for zooming cameras equipped
with the specified lens.
!3 Program Preset button (PROGRAM PRESET)
This button, in combination with the Numeric buttons
and CAMERA (ENTER) button, is used to save a preset
position of the camera in a system equipped with the
specified cameras.
To save a preset position, move the camera to the posi-
tion to be preset and select a preset number by press-
ing the Numeric buttons. Hold down the PROGRAM
PRESET button, then press the CAMERA (ENTER) but-
ton.
!4 Call Preset button (CALL PRESET)
This button, in combination with the Numeric buttons, is
used to move to a preset position of the selected cam-
era in a system equipped with the specified cameras.
!5 Camera / Enter button [CAMERA (ENTER)]
CAMERA: This button is used for camera selection.
Select a camera by pressing the corresponding
Numeric buttons, followed by the CAMERA (ENTER)
button.
ENTER: This button, in combination with the Numeric
buttons, is used to enter numeric input, such as
operator ID and password.
It is also used to execute the currently highlighted
selection and enter a submenu of the Camera
Menu.
Pressing CAMERA (ENTER) while holding down the
SHIFT button will activate the auto panning function of
the selected camera (AUTO PAN).
53
!6 Clear / Escape button [CLEAR (ESC)]
Clear: This button is used to clear numeric input from
the LED Display.
Escape: This button is used to escape from the current-
ly highlighted selection and return to the previous
page of the Camera Menu.
This button is also used to exit from alarm selecting
mode to normal operation mode.
!7 Numeric buttons (0 - 9)
These buttons are used for numeric input into the sys-
tem such as the camera and monitor number,
sequence number, preset position, etc..
Pressing the buttons shown below while holding down
the SHIFT button will select special functions.
1: Turns off the user auxiliary 1 switch of the receiver.
(AUX1 OFF)
2: Turn on the user auxiliary 1 switch of the receiver.
(AUX1 ON)
3: Turns on the housing wiper of the camera until
these buttons are released. (WIPER)
4: Turns off the user auxiliary 2 switch of the receiver.
(AUX2 OFF)
5: Turns on the user auxiliary 2 switch of the receiver.
(AUX2 ON)
7: Turns off the housing defroster of the camera. (DEF
OFF)
8: Turns on the housing defroster of the camera. (DEF
ON)
!8 Shift button (SHIFT)
Pressing this button in combination with buttons to
which special functions have been assigned will acti-
vate these functions.
!9 Alarm button (ALARM)
This button, in combination with the Numeric buttons, is
used to select an alarm. To select an activated alarm,
press the Numeric buttons, followed by the ALARM but-
ton.
This button is also used to arm or disarm cameras and
monitor for alarm response. Select an alarm number by
pressing the Numeric buttons, follqwed by the ALARM
button. Then pressing this button repeatedly will arm or
disarm the active monitor with the selected alarm. The
indicator lights to indicate that the selected alarm is dis-
armed.
@0 Alarm Acknowledge button (ACK)
Acknowledges an activated alarm.
To acknowledge the activated alarm, first select the
alarm by pressing the Numeric buttons, followed by the
ALARM button. Select the desired alarm action number
by pressing the Numeric buttons, then press the ACK
button. The indicator will light.
After acknowledging the alarm, press the RESET button
to reset the alarm. The ACK indicator will go off.
Advertisement
Table of Contents
