Page 1
AEP Model With SUPPLEMENT-1 UK Model (9-922-706-81) E Model HCD-ED1 is the tuner, deck, CD and amplifier section in CMT-ED1. This stereo system is equipped with the Dolby* B- Model Name Using Similar Mechanism type noise reduction system. Base Unit Type...
Page 2
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. – 2 –...
TABLE OF CONTENTS SERVICING NOTE 1. GENERAL ................4 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT 2. DISASSEMBLY 2-1. CD Door, CD Base and Base Unit ........6 The laser diode in the optical pick-up block may suffer electrostatic 2-2.
SECTION 1 GENERAL Location of Parts and Controls FRONT PANEL 1 Displa y windo w 2 DBFB lamp 3 CD SYNC lamp 4 REC lamp 5 ª button 6 BAND FM button 7 POWER b utton º – b utton 8 TUNING 9 §...
Page 5
REMOTE 1 DISPLAY button 2 DBFB b utton 3 CD b utton 4 TUNER/BAND b utton 5 TAPE œ button 6 DIR MODE b utton 7 CD REPEA T button b uttons 9 ON/OFF b utton b uttons 11 VOL (+/–) b utton 12 STEREO/MONO b utton 13 TUNING/PLAY MODE b utton 14 DOLBY NR b utton...
SECTION 2 DISASSEMBLY Note: Follo w the disassemb ly pr ocedure in the n umerical or der given. 2-1. CD DOOR, CD BASE AND BASE UNIT 1 Open the CD door. 2 Bar rubber 5 Two hook screws 3 Hinge pin 6 Three screws (K3x8) 7 Three screws (K3x8) 4 Hinge spring...
2-3. BOTTOM COVER AND FRONT PANEL BLOCK 5 Front panel block 3 Bottom cover 4 Two claws 2 Two screws 1 Two screws (BVTP 3x8) (BVTP 3x8) 2-4. DOOR COVER ASSY AND MECHANICAL DECK (CASSETTE) 4 Four screws (BVTP 3x10) 3 Door spring 5 Mechanical deck (cassette)
SECTION 3 SECTION 4 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION DECK SECTION 0 dB=0.775V 1. Clean the following parts with a denatured alcohol-moistened 1. Demagnetize the record/playback head with a head damagnetizer. swab : (Do not bring the head demagnetizer close to the erase head.) record/playback heads pinch rollers 2.
Page 9
2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak. Procedure : Mode : Playback test tape WS-48B frequency counter...
Page 10
Record Bias Adjustment 2. Mode: Playback Procedure : recorded level meter 1. Mode : Record position MD IN (JK301) 1) 315Hz 50 mV (–23.8 dB) 2) 10kHz AF OSC blank tape CS-123 MD OUT (JK301) attenuator Confirm playback the signal recorded in step 1 become adjustment level as follows.
Page 11
S Curve Check CD SECTION oscilloscope Note: BD board 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. TP (FEO) 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (VC) – 3. Use an oscilloscope with more than 10M impedance. 4.
Page 12
E-F Balance (1 Track Jump) Check Adjustment Location: (Without remote commander) [BD BOARD] — Component Side — oscilloscope BD board RV101 TP (TE) TP (VC) – IC101 RV103 Procedure : 1. Connect oscilloscpe to test point TP (TE) on BD board. 2.
SECTION 5 DIAGRAMS 5-1. CIRCUIT BOARDS LOCATION FM/AM TUNER THIS BLOCK IS SUPPLIED AS THE ASSEMBLED BLOCK FUN/SURROUND board TAPE PREAMP board VOL/POWER board BD board DISPLAY board CD DOOR SW board CONTROL BLK ASSY RELAY board THIS BLOCK IS SUPPLIED AS THE ASSEMBLED BLOCK –...
5-2. IC PIN FUNCTION • IC201 MASTER CONTROL (TC9613) Pin No. Pin Name Function — Ground XOUT 8 MHz Oscillator output 8 MHz Oscillator input RESET CPU reset input TUNED Station detector input STEREO Stereo signal input TEST Test pin (Connected to ground) POWDEC Power down detect input REMOTE...
Page 15
Pin No. Pin Name Function — +5V power supply NARROW Narrow LED output NORMAL Normal LED output LOUD Loudness on/off control output DBFB — Not used (Connected to ground) VOL CLK Volume control clock output VOL DATA Volume control data output VOL STB Volume control strobe output FUNC A...
SECTION 6 EXPLODED VIEWS NOTE: The components identified by • Hardware (# mark) list and accessories and pack- • -XX, -X mean standardized parts, so they may have mark ! or dotted line with mark ing materials are given in the last of this parts list. some difference from the original one.
Page 30
6-2. REAR PANEL SECTION (EXCEPT US,CND,UK) (UK) (HK) (US,CND) not supplied S501 (MY, SP,HK) not supplied T501 FRONT PANEL Les composants identifiés par The components identified by mark ! or dotted line with mark une marque ! sont critiques pour ! are critical for safety.
6-3. FRONT PANEL SECTION Z201 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-997-351-01 DOOR COVER X-4949-449-1 FRONT PANEL SUB ASSY 4-997-354-01 DOOR SPRING X-4949-450-1 CASS DOOR SUB ASSY 4-997-362-01 DOOR LATCH 1-773-009-11 WIRE (FLAT TYPE) (15 CORE) (AEP,UK,EE,CIS) 1-759-548-11 DECK, MECHANICAL 1-751-688-11 WIRE (FLAT TYPE) (13 CORE) 4-997-357-01 GEAR HOLDER...
Ver 1.1 2001.06 6-4. MECHANISM DECK SECTION (CASSETTE) not supplied M901 not supplied not supplied not supplied not supplied not supplied supplied not supplied not supplied not supplied supplied supplied not supplied not supplied supplied not supplied not supplied not supplied (including Ref.
Ver 1.1 2001.06 6-5. BASE UNIT SECTION (BU17-BD19) M101 M102 Les composants identifiés par The components identified by une marque ! sont critiques pour mark ! or dotted line with mark ! are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une specified.
SECTION 7 ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by may be different from the parts specified in the In each case, u: , for example: mark ! or dotted line with mark uA...: A..., uPA...: PA..., uPB...: PB..., diagrams or the components used on the set.
Page 35
CD DOOR SW DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R122 1-216-097-91 METAL GLAZE 100K 1/10W A-4407-244-A CD DOOR SW BOARD, COMPLETE R123 1-216-099-00 METAL CHIP 120K 1/10W *************************** R124 1-216-091-00 METAL CHIP 1/10W <...
Page 41
VOL/POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JACK > R492 1-247-843-11 CARBON 3.3K 1/4W R493 1-249-437-11 CARBON 1/4W JK901 1-784-353-11 JACK (DIN)(SPEAKER L) R494 1-249-437-11 CARBON 1/4W JK902 1-784-353-11 JACK (DIN)(SPEAKER R) R495 1-249-425-11 CARBON 4.7K 1/4W F...
Page 42
HCD-ED1 Ref. No. Part No. Description Remark 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) M101 X-4917-523-4 MOTOR ASSY (SPINDLE) M102 X-4917-504-1 MOTOR ASSY (SLED) M901 X-4949-564-1 MTR MAIN BLK ASSY (CAPSTAN/REEL) ! S501 1-771-308-11 SELECTOR, POWER (MY,SP,HK) ! T501 1-431-697-21 TRANSFORMER, POWER (AEP,UK,EE,CIS)
Page 43
HCD-ED1 US Model Canadian Model SERVICE MANUAL AEP Model UK Model E Model 1998. 04 SUPPLEMENT-1 File this supplement with the service manual. • CHANGES OF LAMP (ENG-98003) • The lamp on the DISPLAY board was changed to a type which use LED from following serial numbers.
Page 44
NEW TYPE (use LED) Page FORMER TYPE (use lamp) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark *** LED BOARD *** *** LED BOARD *** – 1-670-517-11 LED BOARD 8-719-064-63 DIODE SELU5823A-TP15 8-719-064-63 DIODE SELU5823A-TP15 1-247-807-11 CARBON 1/4W 1-249-404-00 CARBON 1/4W...
Page 46
HCD-ED1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.06...