Page 1
DIGITAL PLAIN PAPER COPIER e-STUDIO120/150 (DP-1210/1510) File No. SME02000600 R02082121000-TTEC...
Page 2
Copyright 2002 TOSHIBA TEC CORPORATION Parts marked with “ ” are important for maintaining the safely of the machine. Be sure to replace these parts with the replacement parts specified to maintain the safety and performance of the machine. This document has been published to be used for after sales service only.
Page 3
The installation and service should be done by a qualified service technician.
Page 5
CAUTION This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Page 6
At the production line, the output power Caution of the scanner unit is adjusted to 0.57 This product contains a low power laser MILLI-WATT PLUS 20 PCTS and is device. To ensure continued safety do not maintained constant by the operation of remove any cover or attempt to gain access the Automatic Power Control (APC).
Page 12
>@ &21680$%/( 3$576 6XSSO\ V\VWHP WDEOH (QYLURQPHQWDO 3URGXFWLRQ FRQWURO QXPEHU ORW 1R LGHQWLILFDWLRQ 7RQHU FDUWULGJH! 1RUPDO RSHUDWLQJ FRQGLWLRQ ° Production month ± Production day $FFHSWDEOH RSHUDWLQJ FRQGLWLRQ Destination code Humidity (RH) (Dealer, distributor, OEM, etc.) Production place (SOCC: Fixed to B.) End digit of year...
Page 13
7RQHU FDUWULGJH UHSODFHPHQW Production control label attachment position Production control label attachment position(*1) ∗ 'HYHORSHU! Sub lot Production day Production month End digit of year Production place...
Page 31
An OPC drum is used for the photoconductor. (Structure of the OPC drum layers) OPC layer (20 microns thick) Pigment layer (0.2 to 0.3 microns thick) Aluminum drum Main charger Laser beam Cleaning blade MG roller Drum Transfer unit Resist roller Semiconductor laser Focus correction lens Main high voltage unit...
Page 32
Semiconductor laser Exposure (semiconductor laser) OPC layer Pigment layer Aluminum drum Drum surface charge after the exposure OPC layer Pigment layer Aluminum layer Non-image area Image area About DC5.5KV ( 580V/ 400V)
Page 33
:Carrier (Magnetized particle) :Toner (Charge negative by friction) (N) (S) Permanent magnet (provided in three locations) About DC 5.2kV MG roller 400V 8V...
Page 35
Scanner section Operation section Printer/ MCU (Main control/image process section) Scanner I/F USB or Parallel Note: The scanner function is effective only by USB connection. LSU (Laser unit) Laser diode, Polygon mirror lens Laser beam Paper exit Fusing section Process section Printer section Paper transport section Manual paper...
Page 37
θ θ θ a ≠ b ≠ c d = e = f f θ LENS Thermostat Separator pawl PPD2 Thermistor Pressure roller Heat roller Paper guide...
Page 38
Thermostat Thermistor Heat roller Heater lamp Separator pawl Heated by the heater lamp. (800W) Safety device The surface temperature (thermostat) of the upper heat roller is sensed by the thermistor. Level of the thermistor is controlled by the main PWB. Triac (in the power supply unit) With the signal from the...
Page 42
Apply grease (Molykote X5-6020) ∗ : Check while pressing the blade. Cleaning blade ∗ 0 – 0.3 mm 0 – 0.3 mm ∗ Moquette R Moquette F Sub blade 0 – 0.5 mm 0 – 0.5 mm Cleaning blade Moquette R Moquette F Sub blade Be careful not to allow the...
Page 43
Lock pawl rear Transfer charger Lock pawl front...
Page 46
Note: Attach the FFC to the base plate securely with duplex tape to prevent against coming loose. Note: Attach the FFC to fit with the marking line. Marking line...
Page 57
Multi paper feed solenoid Seal M1-N Pressure plate holder Attachment reference Attachment reference...
Page 61
(When a 100mm scale is used as the original.) Original (Scale) HARDENED STAINLESS JAPAN 1/2mm Shizuoka HARDENED STAINLESS Paper feed JAPAN direction 1/2mm Shizuoka Reference Comparison point Copy Back of the chart...
Page 62
Original (Scale) HARDDENCD STAINLESS JAPAN 1/2mm Shizuoka Paper feed HARDDENCD direction STAINLESS JAPAN 1/2mm Shizuoka Comparison point Reference Copy...
Page 63
B4 or 8 1/2″ × 14″ paper A4 size rear edge Void amount (Standard value: 2 3mm) Scale image Paper rear edge (Example) Distance between paper lead edge and image: H = 5mm Image loss: R = 3mm Document guide 10mm Center Copy paper...
Page 64
2.0mm or less (Copy A) Copy image Copy paper Shift folding line 2.0mm or less (Copy B) Copy image Copy paper Shift folding line (Paper feed direction) * Use a black chart (TEST CHART BLK) or prepare a chart as shown below.
Page 66
→ → → Start Is there a sub Press the COPY key. code ? Press the clear key. The COPY QUANTITY display blinks to indicate Press the COPY "00" and the machine key. enters the ready state for sub code input. Within 1sec Press the exposure Enter the sub code with...
Page 82
SHOLD, LDEN HSYNC → → CN119 10 pin (SYNC) Outputted. Not delivered. Are SHOLD and LDEN outputted? Check the MCU circuit. (Replace the MCU.) (MCU PWB connector section 2) CN119 peripheral circuit Outputted. (MCU PWB Driver section 1) Check connectors on the LSU. (Same as the pin arrangement of CN119) IC 113 IN (8 pin)/OUT (12 pin) Check for disconnection.
Page 83
Check release of the headlock switch. Check the scanner unit operation with SIM 1-01. Operates. Interface connector Does not operate. The shading sheet does not read. CN120 The check item is the same as that of E7-10. Check the connector. (CN103). Check that the drive belt is properly applied to the scanner unit.
Page 84
Check the main motor operation with SIM 25-01. Operates. MMLD Check the Lock signal. Does not operate. Check the connector CN107 (MCU), and the connector on the motor side. Check the MMLD signal (3 pin). If the MMLD signal is not delivered from the MM, replace the MM. If the MMLD is delivered to the MCU, replace the MCU.
Page 86
>@ 0$,17(1$1&( 0DLQWHQDQFH WDEOH ✩ : Check (Clean, adjust, or replace when required.) : Clean : Replace : Adjust : Lubricate 0DLQWHQDQFH GLVSOD\ V\VWHP (If Stop is selected, the LED will flash and stop at 25K.) Default: Not Stop ∗...
Page 92
γ γ ASIC Scan start Print control section Image process section Print data process circuit Resolution conversion, Zooming, lmage process circuit HSYNC PRINT control VSYNC DRAM control ASIC control resistor I/F section DRAM To CPU bus...
Page 125
$&78$/ :,5,1* ',$*5$0 0$18$/ 3$3(5 )((',1* 81,7 CN123 /MPFS Multi feeding solenoid B5B-PH-K-R Multi Manual Paper Feeding unit CN123 MFD sensor PWB PULUP5V D-GND B5B-PH-K-R Single Manual Paper Feeding unit Manual Paper Feeding unit &,5&8,7 ',$*5$0 ...
Page 126
CAUTION FOR BATTERY DISPOSAL (For USA,CANADA) Contains lithium-ion battery. Must be disposed of properly. Remove the battery from the product and contact federal or state environmental agencies for information on recycling and disposal options.
Page 127
1-1, KANDA NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8842 JAPAN...