Table of Contents
Advertisement
HDMI
HDMI (×1)
Signal format
DisplayPort
DisplayPort connector (×1)
Signal format
Option port
Four (4) ports
Signal format
Parallel remote D-sub 9-pin (female) (×1)
Serial remote (LAN)
Ethernet (10BASE-T/100BASE-TX),
Output
SDI
BNC (×1) (monitor output)
Output signal amplitude:
Output impedance: 75 ohms unbalanced
Transmission distance
3G-SDI: 70 m max.
HD-SDI: 100 m max.
SD-SDI: 200 m max.
Note
The signal from the monitor output
connector does not satisfy the ON-LINE
signal specifications.
3) When using the 5C-FB coaxial cable made by
Fujikura Ltd. or equivalent
4) When using the 5C-2V coaxial cable made by
Fujikura Ltd. or equivalent
DC 5V OUT
Circle 4-pin (female) (×1)
General
Power requirements
100 V to 240 V AC,
1.6 A to 0.8 A, 50/60 Hz
Power consumption
Approx. 145 W (max.)
Approx. 72 W (average power
Inrush current
(1) Maximum possible inrush current at
106
Specifications (BVM-F250A)
HDCP correspondence, Deep Color
correspondence
See "HDMI/DisplayPort" (page 118)
of "Available Signal Formats".
HDCP correspondence, 18/24/30bpp
(bits per pixel) correspondence
See "HDMI/DisplayPort" (page 118)
of "Available Signal Formats".
See "Available Signal Systems"
(page 112) and "Available Signal
Formats" (page 113).
RJ-45 (×1)
800 mVp-p±10%
3)
3)
4)
consumption in the default status)
initial switch-on (Voltage changes
caused by manual switching):
53 A peak, 17 A r.m.s. (240V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
39 A peak, 6 A r.m.s. (240V AC)
Operating temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended: 20 °C to 30 °C (68 °F to
86 °F)
Operating humidity
0% to 90% (no condensation)
Storage/transport temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage/transport humidity
0% to 90%
Operating/storage/transport pressure
700 hPa to 1060 hPa
Mass
Approx. 13.0 kg (28 lb 11 oz)
Supplied accessories
AC power cord (1)
AC plug holder (1)
Operation Guide (Japanese/English) (1)
CD-ROM (1)
Optional accessories
BKM-16R Monitor Control Unit
BKM-37H/BKM-38H Controller
Attachment Stand
SMF-700 Monitor Interface Cable
BKM-220D SDI 4:2:2 Input Adaptor
(with serial number 2100001 or
higher)
BKM-227W NTSC/PAL Input Adaptor
(with serial number 2100001 or
higher)
BKM-229X Analog Component Input
Adaptor (with serial number 2200001
or higher)
BKM-243HS HD/D1-SDI Input Adaptor
(with serial number 2108355 or
higher)
BKM-244CC HD/SD-SDI Closed
Caption Adaptor
BKM-250TG 3G/HD/SD-SDI Input
Adaptor (with serial number 7300001
or higher)
Note
An input adaptor with a specified serial
number may be required for your
intended use.
For the serial numbers of the input
adaptors available for this unit, see "Input
Adaptors" (page 22).
Design and specifications are subject to change without
\
notice.
Advertisement
Table of Contents
