Operation - Bosch ALR 900 Original Instructions Manual
Lawnraker / verticutter
Hide thumbs
Also See for ALR 900:
- Original instructions manual (282 pages) ,
- Operating instructions manual (171 pages) ,
- Original instructions manual (256 pages)
Table of Contents
Advertisement
10 | English
Electrical Safety
Your machine is double insulated for safety and
requires no earth connection. The operating volt-
age is 230 V AC, 50 Hz (for non-EU countries 220
V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre
for details.
Extension cords/leads should only be used if
they comply with H05VV-F, H05RN-F types or IEC
type design (60227 IEC 53, 60245 IEC 57).
If you want to use an extension cable when oper-
ating your product, only the following cable di-
mensions should be used:
2
– 1.0 mm
: max. length 40 m
2
– 1.5 mm
: max. length 60 m
2
– 2.5 mm
: max. length 100 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accordance
with prescribed safety regulations.
If in doubt contact a qualified electrician or the
nearest Bosch Service Centre.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and intend-
ed for outdoor use.
Cable connections should be kept dry and off
ground.
It is recommended for increased electrical safety
to use a Residual Current Device (RCD) with a
tripping current of not more than 30 mA. Always
check your RCD every time you use it.
If the supply cord is damaged, it must be re-
placed by a Bosch Service Centre.
Products sold in GB only: Your product is fitted
with an approved 13 A (BS 1363/A) electric plug
and is protected by a 13 A fuse (ASTA Approved
to BS 1362).
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be in-
serted into a 13 A socket elsewhere.
F 016 L70 480 | (10.10.08)
Assembly
Ensure the cables are not trapped when fold-
ing/unfolding top/bottom handles. Do not
drop the handles.
Assembly of Product
Fix the handle bottom 6 to the body of the ma-
chine with two bolts and wing nuts.
Attach the handle top 1 with the bolts and the
wing nuts to the handle bottom 6.
Note: Ensure that the cable clips supplied are
used to fix the cable to the handle.
Attach cable to cable restraint 5 ensuring that
sufficient cable slack is available.
Grassbox
B
C
Separate the grassbox top from the grassbox
bottom.
Locate the rear of the grassbox top into the rear
of the grassbox bottom and close the two halves
together.
Fasten the two red clips (one per side).
Attach/remove the grassbox 7 as shown.
Adjusting the Cutting Height
Pull the lever top 9 towards the wheel and then
rotate it to the front or rear of the machine to
achieve the desired cutting height.
Repeat this for both sides of the product.
Make sure that both levers 9 are set to the same
position.
Note: In certain conditions, mud can build up on
the tread of the wheels and/or the machine may
sink slightly into the ground. This can effect the
depth of ground penetration.
Operation
Starting
The tines/blades continue to rotate for a few
seconds after the machine is switched off.
Allow the motor and tines/blades to stop ro-
tating before switching "on" again.
Do not rapidly switch off and on.
A
D
Bosch Power Tools
Hide quick links:
Advertisement
Table of Contents
