EPSON TERMINAL PRINTER Stylus 1000 SERVICE MANUAL (ADDENDUM for Stylus 800 SERVICE MANUAL) SEIKO EPSON CORPORATION PRINTER TECHNICAL SUPPORT GROUP 4002262 REV.-A...
Page 2
ADDENDUM REVISION SHEET Revision Issued Date Revision Page Rev.-A 1st issue April 28, 1993...
ADDENDUM Stylus-800/1000 SERVICE MANUAL General Description 1.1 General Description This addendum only summarizes the major features and specifications which specifically applicable to the stylus-looo. 1.1.1 Features printing speed. You can print up to 150 cps in 10 cpi LQ mode and up to 250 cps in 10 cpi DRAFT Fast mode.
Page 4
ADDENDUM Stylus-800/1000 SERVICE MANUAL General Description 1.1.2.2 Paper Handling Specification Friction fed (either from built-in auto sheet feeder or manual insertion slot) Paper Feeding : push tractor feed (from rear tractor unit (optional)) Note) Set the release lever to correct position to select proper feeding system. 1.1.2.3 Paper Specification [With ASFJ <Cut Sheet>...
Page 5
ADDENDUM Stylus-800/1000 SERVICE MANUAL General Description Adjust lever : The adjust lever, attached to the carriage unit, must be set to proper position for the paper thickness, as shown in table below. Table 1-2 Adjust Lever Position Paper Lever Position LEFT Cut Sheet (Horizontal)
Page 6
ADDENDUM Stylus-800/fOOO SERVICE MANUAL General Description Printer Operations 1.1.3 This section describes the basic operation of the printer. 1.1.3.1 Control Panel The control panel of the Stylus-1000 contains six non-lock buttons and nine LED indicators for easy type push controls over the various printer’s functions. () DATA opApEROuT O INK OUT...
Page 7
ADDENDUM General Description StVlus-800/1000 SERVICE MANUAL 1.1.3.2 Default Setting Item default setting items of the Stylus-1000 are as listed in table below. Table 1-3 Default Setting Item Description Menu Contents Factory Setting Character Table Select the character table Italic Print direction is automatically Auto Print Direction selected as to maintains optimal print quality (alignment).
Page 8
ADDENDUM Stylus-800/fOOO SERVICE MANUAL General Description 1.1.3.3 Error Conditions Stylus-1000 detects various errors and indicates them with the LED indicators and buzzer as shown in table below. T de El ror Indication PAUSE Buzzer Recovery Error PAPER INK OUT x 3 times I Set the paper and press the Paper out buttons as follows : 1.
ADDENDUM Operating Principles Stylus-800/1000 SERVICE MANUAL 2.1 Operating Principles The main control circuit of the Stylus-1000 is different is the MAIN BOARD. from the StyluS-800, and C114 This board has an additional comector to which optional mpE-B I/F card figure cm be connected.
ADDENDUM Stylus-800/1000 SERVICE MANUAL Operating Principles 2.1.1 Sensor Circuit BOARD In addition to the sensors built in the C106 MAIN for the MAIN BOARD for the StylUS-8C10, the C114 Stylus-1000 is equipped with a sensor which detect the position of the release lever. The release lever is used to switch between normal paper feed from the built-in ASF and the tractor feed which is ordy available if the optional tractor unit has been installed.
ADDENDUM Stylus-800/1000 SERVICE MANUAL Disassembly and Assembly 3.1 Disassembly and Assembly This addendum only explains the disassembly and assembly procedures specifically applicable to the wtich Stylus-looo. 3.1.1 Printer Mechanism M-4860 Removal Remove the upper case. (Refer to Stylus-800 S/M (Section 3.2.1.)) [Step 1] [Step Remove the power supply unit.
ADDENDUM Stylus-800/1000 SERVICE MANUAL Disassembly and Assembly 3.1.2 Motor Removal Paper Feed Remove the printer mechanism. (Refer to 3.1.1.) [Step 1] Remove two screws ((CBS M3x1O)X2) which fixing the paper feed motor. [Step 2] [Step 3] Turn the paper feed motor for about 90 degree, as shown in figure below, so that one of fixing tab of the motor released from a holding plate.
Page 13
ADDENDUM Disassembly and Assembly Stylus-800/1000 SERVICE MANUAL Feed 3.1.3 Paper Roller Assembly Removal Remove the printer mechanism. (Refer to 3.1.1.) [Step 1] Remove the carriage assembly. (Refer to SVIUS-800 S\M (Section 3.2.6.5.) [Step 2] Remove four screws ((CBB M3x1O)X4, two each at left and right side) and remove the rear base [Step 3] frame.
ADDENDUM Stylus-800/1000 SERVICE MANUAL Adjustment 4.1 Adjustment This addendum only explains the adjustment procedures which specifically applicable to the Stylus-1000. 4.1.1 Paper Gap Adjustment Insert the plastic plate into a paper path from the rear of the printer, at the position shown in figure [Step 1] below.
Part No. Availability 40 cc 1010513 G-26 40 g Grease B702600001 Note) E = EPSON Exclusive product (Not commercially available) Table 6-2. Lubrication Points Ref. No. stylus stylus Lubrication Point Lubricant 1000 Frame Assembly, R (Gear shaft A,B and C)
Page 18
ADDENDUM APPENDIX StyhIs-800/1000 SERVICE MANUAL A.1 Appendix This addendum only explains the comectors which specifically applicable to the Stylus-1000. A.1.l Connector Summary Figure below shows the intercomection between the major components of the Stylus-1000. 06 PSWPSE AC Input ICN2 ] Printer Mechanism (M-4810/4860) .
Page 19
ADDENDUM APPENDIX Stylus-800/1000 SERVICE MANUAL Wmmary Table A-1 Connector Board Location Description Cl 06/114 MAIN Centronics parallel l/F 36 pins HEAD-1 (to printhead) HEAD-2 (to printhead) PE(#l/2)/RE(#3/4) sensor PF motor CR motor PS line (from C106 PSE/PSB) Panel control line (to C106 PNL) (UN) C106 PSEVPSE input...