CPD-100ES CPD-100ES SERVICE MANUAL CPD-100ES Southern Hemisphere Model Equator Model Chassis No.SCC-L15B-A CHASSIS SPECIFICATIONS Picture Tube 0.25 mm aperture grill pitch Standard image area Approx. 270 x 202 mm (w/h) 15 inches measured diagonally x 8 inches) 90-degree deflection Deflection frequency Horizontal: 30 to 70 KHz Video image area (14"...
Page 2
CPD-100ES POWER SAVING FUNCTION This monitor meets the power saving guidelines set The Power Saving function will automati- CAUTION: by the EPA Energy Star Program as well as the more cally put the monitor into Active-off state stringent TC092 guidelines (NUTEK). It is capable of if the power switch is turned on without reduced power consumption when used with a com- any video signal input.
VESA 1 0 0 For the customers using the Windows ®4) nstall the new model information of the Sony computer display 3 1 . 5 kHz/70Hz Apple computer from “Windows95 Monitor Information Disk” into your PC. (To to video output For vertical adjustment install the file, refer to the attached “About the Windows95 Monitor...
Adjustments Press the ¨ >/. buttons. Adjusting the Picture Size Resetting the Adjustment Setting the Color Temperature > . . .to rotate clockwise Data to Factory-preset Levels ..to rotate counterclockwise The adjustment data becomes the individual setting for each The selected color temperature becomes the common setting input signal received.
20 minutes for the best result. the u POWER switch once to activate the Auto- degauss cycle*. If the problem persists, call your authorized Sony dealer from a location near your monitor. Picture is flickering Note the model name and the serial number of your monitor.
CPD-100ES SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL 2-2. SERVICE POSITION Cabinet A board Screw cover Screw cover D board Four screws (BVTP 4 x 16) 2-3. D BOARD REMOVAL A board Five screws (BVTP 3 x 12) One screw (BVTT 4 x 8) Cable stopper Two screws (BVTP 3 x 12)
CPD-100ES 2-4. PICTURE TUBE REMOVAL Demagnetization coil Two screws (BVTP 4 x 16) Tension spring A board Neck assy Deflection yoke Two degaussing Tow degaussing coil holders coil holders Picture tube Four screws (Tapping screw 5) Stand assy (D board) Anode cap Two degaussing Tow degaussing...
CPD-100ES SECTION 3 SAFETY RELATED ADJUSTMENT b) HV Hold-Down Check When replacing parts shown in the table below, the 1) Using an external DC Power supply, apply the following operational checks must be performed as a safety precaution against X-rays emissions from the unit. voltage shown below between cathode of D511 on "D"...
CPD-100ES SECTION 4 ADJUSTMENTS Connect the communication cable of the connector located on the D board on the monitor. Run the service software and then follow the instructions. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR as a Jig D-sub mini Din...
Page 11
CPD-100ES Receive White cross-hatch. <Zero Position NECK Ass'y> Adjust HMC and VMC at six-pole magnet. Purity 4-Pole Mg 6-Pole Mg < 6 Pole Magnet> DY XBV Dot adjustment Receive R.B. cross-hatch. Adjust XBV at DY four-pole magnet. XBV Correction Vertical and Horizontal Position and Size a When Specification Less than...
CPD-100ES 5-2. CIRCUIT BOARDS LOCATION 5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in F unless otherwise noted. pF: • When replacing parts shown in the table below, 50 WV or less are not indicated except for electrolytic. be sure to perform the safety related adjustment.
CPD-100ES SECTION 6 EXPLODED VIEWS • Items with no part number and no • Items marked " * " are not stocked The components Identified by shading and mark ¡ ¡ ¡ ¡ ¡ a re critical for safety. description are not stocked because since they are seldom required for routine they are seldom required for routine service.
CPD-100ES SECTION 7 ELECTRICAL PARTS LIST RESISTORS Note: The components identified by in this manual • have been carefully factory-selected for each All resistors are in ohms set in order to satisfy regulations regarding X- The components Identified by shading •...
Page 19
CPD-100ES Note: Note: The components Identified by shading Les composants identifies per un trame et and mark ¡ ¡ ¡ ¡ ¡ une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la are critical for safety. Replace only with part number specified. securite.
Page 20
CPD-100ES Note: Note: The components Identified by shading Les composants identifies per un trame et and mark ¡ ¡ ¡ ¡ ¡ une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la are critical for safety. Replace only with part number specified. securite.
Page 21
CPD-100ES Note: Note: The components Identified by shading Les composants identifies per un trame et and mark ¡ ¡ ¡ ¡ ¡ une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la are critical for safety. Replace only with part number specified. securite.
Page 22
CPD-100ES Note: Note: Les composants identifies per un trame et The components Identified by shading une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la and mark ¡ ¡ ¡ ¡ ¡ are critical for safety. securite. Ne les remplacer que par une Replace only with part number specified.
Page 23
CPD-100ES Note: Note: The components Identified by shading Les composants identifies per un trame et and mark ¡ ¡ ¡ ¡ ¡ une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la are critical for safety. Replace only with part number specified. securite.
Page 24
CPD-100ES Note: Note: Les composants identifies per un trame et The components Identified by shading une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la and mark ¡ ¡ ¡ ¡ ¡ are critical for safety. securite. Ne les remplacer que par une Replace only with part number specified.
Page 25
CPD-100ES Note: Note: The components Identified by shading Les composants identifies per un trame et and mark ¡ ¡ ¡ ¡ ¡ une marque ¡ ¡ ¡ ¡ ¡ sont critiques pout la are critical for safety. Replace only with part number specified. securite.
Page 26
CPD-100ES Note: Note: The components Identified by shading The components identified by in this manual have been and mark ¡ ¡ ¡ ¡ ¡ are critical for safety. carefully factory-selected for each set in order to satisfy regu- lations regarding X-ray radiation. Should replacement be Replace only with part number specified.