Related Manuals for Miele ULTRA FULLSIZE DISHWASHER
Summary of Contents for Miele ULTRA FULLSIZE DISHWASHER
-
Page 1: Installation Instructions
Installation instructions Dishwasher To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 620 922... - Page 2 11. Make the plumbing connections ........
- Page 3 If there is any doubt concerning installation contact the Technical Installation, maintenance and Service Department. repair work should be by a Miele authorized service technician. Work by USA 1-800-999-1360 unqualified persons could be a hazard techserv@mieleusa.com and may void the warranty.
- Page 4 This data young children. Danger of suffocation! must correspond to prevent injury and If the appliance is removed from its machine damage.
- Page 5 Si vous avez des doutes au sujet de l’installation, contactez le Dé- L’installation et les travaux de répa- partement du service technique Miele. ration et d’entretien doivent être ef- fectués par un technicien de service USA 1-800-999-1360 autorisé Miele. Les travaux effectués techserv@mieleusa.com...
- Page 6 énumérées emballages de plastique, sacs etc. sur la plaque signalétique correspon- et de les garder hors de la porté des dent à la source d’électricité de la rési- bébés et jeunes enfants. Danger de dence. Ces données doivent corres- suffocation! pondre afin d’éviter de vous blesser et...
- Page 7 Before discarding an old bags etc. are disposed of safely and appliance, unplug it from the outlet and kept out of the reach of children. cut off its power cord and remove any Danger of suffocation! doors to prevent hazards.
- Page 8 32 " - 33" (819 - 838 mm) (see Inset). A = Black leg extension (removable) B = White leg (must be installed on machine). ^ After removing the black leg extensions, screw the white legs onto the dishwasher.
- Page 9 Machine heights of 35" - 37" (889 - 940 mm) can be obtained if the supplied legs are removed and extended legs are attached. Contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601).
- Page 10 Machine heights between 35" and 37" (889 - 940 mm) can be obtained if the supplied legs are removed and extended legs are attached. Please contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601).
- Page 11 ^ Secure the deflector in place using laminate edging should be tacked the supplied nails. through the rear holes of the steam ^ Wipe of any excess silicone with a deflector. solution of liquid dish soap and warm ^ Remove the protective film from the water.
- Page 12 ^ First, adjust the height of the legs so that the top of the dishwasher is roughly "...
- Page 13 Exercise care when sliding the dishwasher in or out, to prevent damaging the power cord or hoses. ^ Make a 2" x 4" (5 x 10 cm) cut out in the side or bottom of the cabinet adjoining the dishwasher. This cut out is necessary for connections to pass through.
-
Page 14: Level Legs
^ The rear leveling legs can be ^ Adjust the front leveling legs by adjusted with a T20 Torx screwdriver pushing on the feet with a slotted by turning the screws at the front of screwdriver. the slide skis. ^ Tipping the machine slightly backwards, if posssible will make To raise the machine turn clockwise. - Page 15 The dishwasher must not be operated without the control panel installed. ^ Press the "On/Off" button in and place ^ Position the control panel, c, and the cover, a, over the push button. fasten it from the inside of the door, d, using the six screws provided.
- Page 16 ^ Insert the drying vent grill, b, into its ^ Insert the other button covers, e and opening. f, into their openings.
- Page 17 ^ Press the "On/Off" button in and place ^ Position the control panel, c, and the cover, a, over the push button. fasten it from the inside of the door, d, using the six screws provided. ^ Push the drying vent grill, b, into its opening.
- Page 18 (optional accessory). white 4 047 341 4 312 770 black 4 047 361 4 312 780 ^ Using an 8 mm socket, turn the nut Stainless 3 280 742 4 316 721 clockwise or counterclockwise until Steel 3 298 210 the filler strips line up with the drawer line.
- Page 19 = Toe Kick Height " (19 mm). Custom door panels should be finished Determined using the following on all edges. Trim kits are not available calculation: X = A – B – C for custom door panels. *Control panel height is determined by the height of the drawers in the cabinets.
- Page 20 A custom door panel must not exceed the listed maximum weight. An overweight panel will distort the door springs causing the dishwasher door to fall when opened. Plastic control 13 lbs 12 lbs panel (5.9 kg) (5.5 kg) Stainless Steel 10.5 lbs...
- Page 21 ^ Place a template on each end of the ^ Slide the bracket up or down until the mounting bracket as shown, making oblong holes on the machine door sure the rule marks face the outside line up with the oblong holes on the template (shown in inset a).
- Page 22 ^ Tape the bracket to the door panel to ^ Drill pilot holes for the screws using a hold it in place while the mounting " (2.5 mm) bit. holes are drilled. ^ Attach the bracket to the panel using the 6 screws provided.
- Page 23 ^ Push up one side of the door panel until it touches the filler strips (or control panel if filler strips are not used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. Do not use a power screwdriver.
- Page 24 " (2.5 mm) bit. door bottom to the bottom of the ^ Attach the bracket to the panel using mounting bracket (X). the 6 screws provided. ^ Draw a line on the rear of the door panel (X) inches up from the bottom.
- Page 25 ^ Push up one side of the door panel until it touches the filler strips (or control panel if filler strips are not being used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. Do not use a power screwdriver ^ Repeat the process with the other side of the door panel.
- Page 26 Do not drill any additional holes with the slots in the steam deflector. through any part of the wash cabinet. If in doubt on how to secure the dishwasher, please call Miele’s Technical Service Department. ^ Using flat head screws, secure the...
- Page 27 " (45 cm) or " (60 cm) wide: ^ Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings.
- Page 28 If the door drops, the tension on the springs needs to be increased. If it closes on its own, the tension on the springs need to be decreased. ^ To adjust the door springs use a T20...
- Page 29 The water inlet hose comes equipped with a " female hose thread An air gap is built into the water inlet connector. This can be directly system to prevent potable water from connected to a shut off valve with "...
- Page 30 Do not cut the intake hose. If the hose is cut, the dishwasher will not work. There will be a water leak and you could be injured. If the hose is...
- Page 31 The machine comes equipped with: – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of " (22 mm). Drain hose extensions can be ordered from Miele’s Technical Service Department. – A built-in swivel connector allowing the drain hose to be routed in any direction.
- Page 32 39" (1 m). – If installed horizontally, the drain hose can be up to 12 ft (3.5 m) long. If the drain hose is angled upwards in any way, it cannot be longer than 5 ft (1.5 m).
- Page 33 Rated load:..12.5 A / 1500 W GROUNDED. Voltage: ....120 VAC In the event of a malfunction or Frequency: .
- Page 34 Pass the permanent the compartments of 1 " (3 to 4 cm) power supply cable through the strain can be made to allow the plug to pass relief and secure it to the terminal box. through. Connect: (Black) to L on terminal block...
- Page 35 ^ Check for any leaks, odd noises and flashing / lit fault indicators on the Once the dishwasher is level and control panel. See the "Operating secured it should be tested. Instructions / Frequently asked ^ Remove all packing and literature questions"...
- Page 36 ( ), determine the maximum dishwasher toekick height ( ). If ( ) is equal to or less than the toekick height of the adjoining cabinets, no interference will exist, provided that ( ) is at least...
- Page 37 ^ Push the mounting brackets in as far ^ Push the mounting brackets in as far as possible by releasing the tension as possible by releasing the tension on the spring clip (see illustration).
- Page 38 The included toekick will fit without modification if the machine is set to its maximum height and the toekick is recessed as far as possible (4" / 10 cm). If the machine height is less than maximum, or if the toekick is not recessed 4"...
- Page 39 ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close to the line just drawn, score the front of the toekick, and snap off the excess, otherwise, trim the toekick along the line using a saw.
- Page 40 Alterations rights reserved / (NovoplusB,P,S) / 2703 M.-Nr. 05 620 922 / 01 This bio-friendly paper was bleached without the use of chlorine.