Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
1.1. ELECTRICAL SAFETY.
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
9
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products.
Electrical safety information. It is important that the following information is read and understood:
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a
8
qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Disconnect the grinder from the mains power, and ensure the grinding wheels are at a standstill before attempting to
‰
change accessories, service or perform any maintenance.
DO NOT use a damaged accessory. Before each use, inspect the accessory such as abrasive wheels for chips and cracks.
8
DO NOT operate the grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
8
▲
DANGER! DO NOT use a damaged wheel as it is dangerous and may cause damage and/or serious personal injury.
WARNING! Only persons qualified under the "Abrasive Wheels Regulations" and holding a current grinding wheel certificate are to
‰
change or dress grinding wheels. Unplug grinder from mains power and refer to Section "Grinding Wheels" below for details.
After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run
9
the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
The rated speed of the accessory must be at least equal to the maximum speed marked on the grinder. Accessories running faster
9
than their rated speed can break and fly apart.
Never grind on the sides of a grinding wheel. Grinding on the side can cause the wheel to break and fly apart.
9
Only use accessories with a diameter and maximum thickness specified in the Specification section of this manual.
9
Bench grinders must always be stable and secure e.g. fixed to a bench or the like.
9
Grinding wheels must be correctly mounted and free of defects before use (ring tested).
9
Spark arrestors and work rests must be adjusted frequently so as to compensate for the wear of the wheel.
9
WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
‰
A guard or any other part that is damaged should be repaired or replaced before tool is next used. The eye shields are a mandatory
fitting when grinder is used in premises covered by the Health & Safety at Work Act.
Distance between the spark arrestor/work rest and the wheel must be kept as small as possible and in any case no greater than
9
2mm.
Worn wheels must be replaced when the 2mm gap above can no longer able to be maintained.
9
For tools with two spindles: always use the tool with accessories on both spindles in order to limit the risk of contact with the rotating
9
spindle.
Always use the guard, work rest, transparent screen and spark arrestor as required for the accessory(ies).
9
Damaged or deeply grooved wheels must be replaced.
9
Always adjust the work rest so that the angle between the work rest and the tangent of the accessory is always greater than 85°.
9
Grinding wheels must always be handled and stored in the correct manner.
9
Maintain the grinder in good condition and check moving parts alignment regularly.
9
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
Locate grinder in a suitable working area, keep area clean, tidy and free from unrelated materials. Ensure adequate lighting.
9
Before each use check grinding wheels for condition. If worn or damaged replace immediately.
9
© Jack Sealey Limited
Ø200MM WORKSHOP BENCH GRINDER 600W
BG200XL.V2
MODEL NO:
Wear ear
Wear a
protection
mask
Original Language Version
BG200XL.V2 Issue 2 13/11/23
Advertisement
Related Manuals for Sealey BG200XL.V2
Summary of Contents for Sealey BG200XL.V2
- Page 1 BG200XL.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Fitted with copper wound induction motor. Suitable for general workshop grinding and sharpening use. Two aluminous oxide grinding stones, coarse and fine. Fitted with stone guards and spark arrestors. Eye shields included. Supplied with 3-pin plug.. 3. SPECIFICATION fig.1 Model No ........... BG200XL.V2 Axle Diameter ............16mm Fuse Rating: ..............5A Motor power: ............600W Grinder wheel ........200mm Diameter...
- Page 3 The machine motor and bearing are sealed units and require no regular maintenance. Should you require assistance, contact your local Sealey service agent. 7.4. For information relating to the handling and maintenance of grinding wheels refer to section 5. Original Language Version BG200XL.V2 Issue 2 13/11/23 © Jack Sealey Limited...
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...