Related Manuals for Asus AAEON UP Xtreme 7100 Edge
Summary of Contents for Asus AAEON UP Xtreme 7100 Edge
- Page 1 UP Xtreme 7100 Edge Maker Board System UPX-EDGE-ASL01 User’s Manual 1st Ed Last Updated: November 15, 2023...
- Page 2 Copyright Notice This document is copyrighted, 2023. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
- Page 3 Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft®, Windows®, Windows® 10 IoT Enterprise, and Windows® IoT Core ⚫ are registered trademarks of Microsoft Corp. Intel® and Atom® are registered trademarks of Intel Corporation ⚫ Core™...
- Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UP Xtreme 7100 Edge (UPX-EDGE-ASL01) ⚫ DC in Phoenix Block Connector ⚫ RS-232/422/485 Block ⚫ DIO/GPIO Phoenix Connector ⚫ CAN Phoenix Connector ⚫...
- Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document.
- Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
- Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
- Page 8 FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
- Page 9 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON System QO4-381 Rev.A0 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 × ○ ○ ○ ○ ○ 连接器及线材 ○ ○...
- Page 10 China RoHS Requirement (EN) Hazardous and Toxic Materials List AAEON System QO4-381 Rev.A0 Hazardous or Toxic Materials or Elements Component Name PCB and Components Wires & Connectors for Ext.Connections Chassis CPU & RAM HDD Drive LCD Module Optical Drive Touch Control Module Battery This form is prepared in compliance with the provisions of SJ/T 11364.
-
Page 11: Table Of Contents
Table of Contents Chapter 1 - Product Specifications..................1 Specifications ......................2 Chapter 2 – Hardware Information ..................4 Dimensions ....................... 5 Jumpers and Connectors ..................6 List of Jumpers and Connectors ................7 2.3.1 Power Button (1) ................... 8 2.3.2 9-36V DC in (2) .................... -
Page 12: Chapter 1 - Product Specifications
Chapter 1 Chapter 1 - Product Specifications... -
Page 13: Specifications
Specifications System Intel® Core™ i3-N305 Intel® Processor N97 Memory Up to 16GB LPDDR5 Graphics Intel® UHD Graphics for 12th Gen Intel® Processors Storage Up to 64GB eMMC Ethernet 2.5GbE x 2 (Intel® I226-IT) WIFI/BT Optional with M.2 2230 E-Key x 1 Expansion M.2 3052 B-Key x 1 with Nano SIM Slot (USB 3.0) M.2 2230 E-Key x 1 (USB 2.0/PCIe) - Page 14 Ethernet RJ-45 x 2 RS-232/422/485 x 1 (Terminal Block, Default RS-232) Audio — GPIO 6-pin GPIO x 1 via Terminal Block Power Supply Power Requirement 9-36V Power Supply Type AT/ATX (AT as default) Power Consumption 52W ~ 55W Mechanical Mounting 75mm x 75mm VESA Mount Wall Mount Kit (Optional) Dimensions (W x H x D)
-
Page 15: Chapter 2 - Hardware Information
Chapter 2 – Hardware Information Chapter 2... -
Page 16: Dimensions
Dimensions Chapter 2 – Hardware Information... -
Page 17: Jumpers And Connectors
Jumpers and Connectors Front I/O Rear I/O Chapter 2 – Hardware Information... -
Page 18: List Of Jumpers And Connectors
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers and connectors that you can configure for your application. Label Function Power Button 9-36V DC in USB Type C (DP 1.4a) USB 3.2 Type A-1 USB 3.2 Type A-2 USB 2.0 Type A-1 USB 2.0 Type A-2... -
Page 19: Power Button (1)
2.3.1 Power Button (1) Power button can be used to switch system on/off. 2.3.2 9-36V DC in (2) One DC two-pole terminal block supporting a DC power range of 9 ~ 36V. Signal Signal 9 – 36V DC_IN 2.3.3 USB 3.2 (Type-C) (3) The USB Type-C port provides one USB 3.2 signal with Display Port 1.4a support. -
Page 20: Usb 3.2 Gen 2 (Type-A) (4/5)
2.3.4 USB 3.2 Gen 2 (Type-A) (4/5) The port provides two USB 3.2 Gen 2 interfaces. 2.3.5 USB 2.0 (6/7) The port provides two USB 2.0 interfaces. Chapter 2 – Hardware Information... -
Page 21: Lan 1 (Intel® I226-It) (8)
2.3.6 LAN 1 (Intel® I226-IT) (8) Note: The controller provides Gigabit ethernet ports with 10/100/1000/2500 Base. 2.3.7 LAN 2 (Intel® I226-IT) (9) Chapter 2 – Hardware Information... -
Page 22: Digital I/O & Gpio (10/11)
2.3.8 Digital I/O & GPIO (10/11) The controller provides one 8-in/8-out Digital I/O & 6-pin GPIO via Terminal Block interface. 2.3.8.1 Digital I/O (10) The controller provides one 8-in/8-out Digital I/O function via Terminal Block interface. Please note pin 1 ~ 4 is SINK; pin 5 ~ 8 is SRC. Pin Definition Signal Signal... -
Page 23: Gpio (11)
Signal Signal DOUT5 DIN5 DOUT6 DIN6 DOUT7 DIN7 DOUT8 DIN8 DGND DGND DGND DGND 2.3.8.2 GPIO (11) The controller provides 6-pin GPIO function via Terminal Block interface. Pin Definition Signal Signal GPIO1 GPIO2 GPIO3 GPIO4 Chapter 2 – Hardware Information... - Page 24 Signal Signal GPIO5 GPIO6 GPIO Voltage Level The controller provides a jumper to change the GPIO voltage level. The default is 3.3V (pin 1-2). To change GPIO voltage settings, please remove chassis and allocate jumper base on following table Signal Signal V3P3_GPIO VGPIO...
-
Page 25: Can (13)
2.3.9 CAN (13) The controller provides one 6-pin terminal block for 2-channel CAN 2.0B protocol There are two LED on UPX-ADNL01-AMR Edge with LED assignment and description are shown as follows: Pin Definition Pin Definition Table Signal Signal CAN1_H CAN2_H CAN1_L CAN2_L Chapter 2 –... -
Page 26: Can Term (Dip Switch) (14)
LED Assignment: LED Name LED Color Description CAN 1 Green LED flashing while CAN transmission LED flashing while error occurred CAN 2 Green LED flashing while CAN transmission LED flashing while error occurred 2.3.10 CAN Term (DIP Switch) (14) The controller provides one built-in 120Ω terminal resistor for CAN 1/CAN 2 ports, users can decide if it is enabled or not. -
Page 27: Com (15)
2.3.11 COM (15) Terminal block interface for RS-232/422/485 function. Default setting is RS-232. Please see the hardware pin assignment and table below. Signal Signal DCD/RS422TX-/RS485- RX/RS422TX+/ RS485+ TX / RS422RX+ DTR / RS422RX- To change the Serial Port Configuration setting, please follow the steps below: Step 1: Reboot system and press “Deletei”... - Page 28 Step 4: Press “F4” to save the configuration and exit. Chapter 2 – Hardware Information...
-
Page 29: List Of Internal Slots
List of Internal Slots Slot Function Wi-Fi Slot M.2 2230 E-Key (USB 2.0/PCIe Gen 3 [x1] interface) Storage Slot M.2 2280 M-Key (PCIe Gen 3 [x2] interface) LTE Module Slot M.2 3052 B-Key (USB 3.0 only) SIM Slot Nano SIM Slot Chapter 2 –... -
Page 30: Chapter 3 - Enable Can Function
Chapter 3 Chapter 3 – Enable CAN Function... -
Page 31: Enable Can Function
Enable CAN Function For Linux Ubuntu 22.04, please refer to the below interface and device name mapping table to enable CAN 1 and CAN 2 functions. Function Description Interface Device Name CAN 1 UART ttyS4 CAN 2 ttyACM0 Chapter 3 – Enable CAN Function... -
Page 32: Appendix A - Cables And Connectors
Appendix A Appendix A – Cables and Connectors... -
Page 33: List Of Cables And Connectors
List of Cables and Connectors This table provides detailed information about the cables and connectors used by UPX-EDGE-ASL01 (UP Xtreme 7100 Edge) If you have any questions about the configuration, please contact your AAEON sales representative. Function Mating Cable Mating Cable Description Description DC In 165260210A... -
Page 34: Appendix B - Power Adapter Configuration
Appendix B Appendix B – Power Adapter Configuration... -
Page 35: Connecting 2-Pin Dc Connector With Dc Adapter
Connecting 2-Pin DC Connector with DC Adapter Step 1: Locate DC connector with 2-pin Phoenix DC connector provided in the UP Xtreme 7100 Edge packing box. Pin Definition: Step 2: Connect the cable from the adapter (note that power cable must connect to the ”+”...