Page 1
WB150-2N A60029 This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America Corp. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or add improvements at any time without incurring any obligation to install such changes on products sold previously.
Page 2
Find manuals at https://best-manuals.com...
Page 3
PARTS BOOK - PAPER: Chassis and Engine - WB140-2N ....... BEPB040401 Chassis and Engine - WB150-2N .
Page 4
REQUISITION FOR TECHNICAL SERVICE PUBLICATIONS AND SERVICE FORMS COMPLETE FORM DataKom Publications and Training Division AND RETURN TO 440 North Fairway Drive Vernon Hills, IL 60061-8112 U.S.A. Attn: Service Publications Fax No. (847) 970-4186 Tel No. (847) 970-5887 COMPANY NAME PURCHASE ORDER NO.
Page 5
Komatsu warrants to the ultimate purchaser and each subsequent purchaser that the engine is designed, built and equipped so as to conform, at the time of sale by Komatsu, with all U.S. Federal emission regulations applicable at the time of manufacture and that it is free from defects in workmanship or material which would cause it not to meet these regulations within five years or 3,000 hours of operation, whichever occurs first, as measured from the date of delivery of the engine to the ultimate purchaser.
Page 6
Find manuals at https://best-manuals.com...
Page 7
INTRODUCTION WB140-2N, WB150-2N Find manuals at https://best-manuals.com...
KOMATSU delivers machines that comply with all applicable regulations and standards of the country to which it has been shipped. If this machine has been purchased in another country or purchased from someone in another country, it may lack certain safety features and specifications that are necessary for use in your country.
The safety precautions are described in SAFETY section 1. KOMATSU cannot predict every circumstance that might involve a potential hazard in operation and maintenance. Therefore the safety message in this manual and on the machine may not include all possible safety precautions. If any procedures or actions not specifically recommended or allowed in this manual are used, you must be sure that you and others can do such procedures and actions safely and without damaging the machine or causing injury.
★ LOADING, SCRAPING OR GRADING OPERATIONS. ★ EXCAVATING. Installation of optional equipment can also be used in the following applications, use only KOMATSU approved equipment. ★ HANDLING OF MATERIALS (MP BUCKET - PALLET FORKS). ★ SNOWPLOWING (ANGLE DOZER BLADE - SNOWPLOW).
On machines in which synthetic biodegradable types of oils are used, the following operations are to be performed besides the standard maintenance operations: ★ After the first 50 hours of operation, change the hydraulic system filter. ★ After the first 500 hours of operation, change the hydraulic system oil and filter. WB140-2N, WB150-2N...
The machine serial number is stamped on the right side of the front part of the main tractor frame. MACHINE IDENTIFICATION PLATE The Komatsu backhoe loaders described in this manual are provided with the CE mark which certifies that they are in compliance with the CE standards.
The serial number for the front axle is stamped on a plate located on the right side of the axle housing. REAR AXLE SERIAL NUMBER The serial number for the rear axle is stamped on a plate located on the right side of the axle housing. WB140-2N, WB150-2N...
The serial number for the cab is stamped on a plate located on the right center pillar. CANOPY SERIAL NUMBER The serial number for the canopy is stamped on the plate located on the inside upper right corner. WB140-2N, WB150-2N...
Page 27
1SAFETY WARNING! Read and follow all safety precautions. Failure to do so may result in serious injury or death. This safety section also contains precautions for optional equipment and attachments. WB140-2N, WB150-2N...
★ Your distributor can supply you with new replacement decals if the ones on the machine are damaged or missing. When replacing damaged or missing decals, be sure they are placed in the proper location. Additional safety or warning decals may be added to your machine if desired. WB140-2N, WB150-2N...
Page 30
It is always a good idea to be aware of your clearances around, in front, behind and especially above your work area or travel route. Because of the additional height posed by the backhoe boom 1 m is added above the canopy when the machine is in the travel posture. WB140-2N, WB150-2N...
Page 31
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...