Related Manuals for Sony LMD-2110MD
Summary of Contents for Sony LMD-2110MD
- Page 1 5-045-765-12(1) 2023-10 LCD Monitor Instructions for Use Before operating the unit, please read this manual thoroughly and retain it for future reference. LMD-2110MD © 2011 Sony Corporation...
- Page 2 Indications for Use/Intended Use This symbol indicates the manufacturer, The LCD Monitor is intended to provide 2D color and appears next to the manufacturer’s video displays of images from surgical name and address. endoscopic/laparoscopic camera systems and This symbol indicates the Importer, and other compatible medical imaging systems.
- Page 3 IEC 60601-1 standards. If expense. in doubt, consult qualified Sony service You are cautioned that any changes or personnel. modifications not expressly approved in this manual could void your authority to operate this 3.
- Page 4 • Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-2110MD. Otherwise, degradation of the performance of this equipment could result. • If the LMD-2110MD will be used adjacent to or stacked with other equipment, normal operation of the LMD-2110MD under such configurations should be verified via observation.
- Page 5 Guidance and manufacturer’s declaration – electromagnetic immunity The LMD-2110MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-2110MD should assure that it is used in such an environment. IEC 60601 Immunity test Compliance level Electromagnetic environment –...
- Page 6 Guidance and manufacturer’s declaration – electromagnetic immunity The LMD-2110MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-2110MD should assure that it is used in such an environment. IEC 60601 Compliance Immunity test Electromagnetic environment –...
- Page 7 If the measured field strength in the location in which the LMD-2110MD is used exceeds the applicable RF compliance level above, the LMD-2110MD should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the LMD-2110MD.
- Page 8 The LMD-2110MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-2110MD. Otherwise, degradation of the performance of this equipment could result.
- Page 9 2. Use the Power Cord (3-core mains lead) / attached. Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere). Consult with Sony qualified personnel for the following types of installation location. If you have questions on the use of the above – Wall mount Power Cord / Appliance Connector / Plug, please –...
- Page 10 For the customers in the U.S.A. SONY LIMITED WARRANTY - Please visit www.sony.com/psa/warranty for important information and complete terms and conditions of Sony’s limited warranty applicable to this product. For the customers in Canada This symbol and its variations indicate that this...
-
Page 11: Table Of Contents
Table of Contents Precaution .............12 On Safety ............12 On Installation ..........12 About the LCD Panel ........12 On Burn-in ............12 On a Long Period of Use ........12 On Cleaning ............13 Disposal of the Unit ..........13 Recommendation to Use more than One Unit ............13 On Repacking ...........13 On Fan Error .............13 On Moisture Condensation .......13... -
Page 12: Precaution
• Do not push or scratch the LCD screen. Do not place Precaution a heavy object on the LCD screen. This may cause the screen to lose uniformity. • If the unit is used in a cold place, a residual image may appear on the screen. -
Page 13: On Cleaning
If you have any questions about this unit, contact your On cleaning the monitor authorized Sony dealer. A material that withstands disinfection is used for the medical use LCD monitor. When solvents such as benzene or thinner, or acid, alkaline or abrasive... -
Page 14: Features
External sync input Features When the EXT SYNC button is in the on position, the unit can be operated on the sync signal supplied from an external sync generator. The LCD Monitor is to provide color video displays of Automatic termination (connector with images from medical imaging systems on LCD (liquid mark only) crystal display) panel. -
Page 15: Location And Function Of Parts And Controls
Location and Function of Parts and Controls Front Panel MENU VOLUME RGB/ BLUE LINE HDMI COMPONENT SYNC ONLY SCAN ASPECT RESET ENTER qs qa 0 9 8 7 6 4 3 2 a Tally lamp ENTER button Turning this lamp on or off can be done with a Press to confirm a selected item on the menu. -
Page 16: Input Signals And Adjustable/Setting Items
m LINE button n Speaker Press to monitor the signal through the LINE input The audio signal selected by the input select button ( connector. SDI button, RGB/COMPONENT button, HDMI button or LINE button) on the front panel is output. Input Signals and Adjustable/Setting Items Input signal Item... -
Page 17: Rear Panel
OPTION IN connector (D-sub 9-pin, female) Analog RGB signal or component (Y/P ) signal input connectors and their loop-through output Inputs HD/SD-SDI signals when optional Sony BKM- connectors. 341HS is connected. Press the RGB/COMPONENT button to monitor the Press the SDI button to select the signal. - Page 18 AUDIO IN/OUT (phono jack) VIDEO IN/OUT (BNC) When using an analog RGB or a component signal These are the input/output connectors for a as a video signal, use these jacks for the input/output composite video signal. Connect them to the of an audio signal.
-
Page 19: Connecting The Ac Power Cord
Connecting the AC Attaching the Input Power Cord Adaptor Plug the AC power cord into the AC IN socket on Before attaching the input adaptor, disconnect the power the rear panel. Then, attach the AC plug holder cord. (supplied) to the AC power cord. BKM-341HS Tighten the screws. -
Page 20: Removing The Connector Cover
Removing the Selecting the Default Connector Cover Settings When the unit is shipped from the factory, a connector When you turn on the unit for the first time after cover is attached to the PARALLEL REMOTE purchasing it, select the area where you intend to use this connector. - Page 21 2 If LATIN AMERICA is selected: PAL&PAL-N area L A T I N A M E R I C A P A L & P A L - N A R E A Argentina A R G E N T I N A P A R A G U A Y Paraguay U R U G U A Y...
-
Page 22: Selecting The Menu Language
The setting items (icons) in the selected menu are Selecting the Menu displayed in yellow. Language SYSTEM SETTING 1/2 xxxxxxx R G B / C O M P S E L : xxxxxxx C O M P O N E N T L E V E L : xxxxxxx N T S C S E T U P : You can select one of eight languages (English, French,... -
Page 23: Using The Menu
Using the Menu SYSTEM SETTING 1/2 R G B / C O M P S E L : xxxxx C O M P O N E N T L E V E L : N T S C S E T U P : xxxxxx The unit is equipped with an on-screen menu for making S C A N :... -
Page 24: Adjustment Using The Menus
REMOTE Adjustment Using the PARALLEL REMOTE 1PIN Menus 2PIN 3PIN 4PIN 6PIN Items 7PIN 8PIN The screen menu of this monitor consists of the following items. KEY INHIBIT STATUS (the items indicate the KEY INHIBIT current settings.) For the video input Adjusting and Changing the FORMAT Settings... -
Page 25: Color Temp/Bal Menu
For the DVI input Submenu Setting MANUAL If you set the COLOR TEMP to ADJUSTMENT USER setting, the item displayed is STATUS 1/2 changed from black to white, which F O R M AT means you can adjust the color xxxxxxx xxxxxxx temperature. -
Page 26: System Setting Menu
SYSTEM SETTING menu Submenu Setting The SYSTEM SETTING menu is used for setting the FORMAT DISPLAY Selects the display mode of the system. You can set the display language and so on. signal format. • AUTO: The format is displayed Items that cannot be adjusted depending on the input for about 10 seconds when signal are displayed in black. -
Page 27: Remote Menu
Scan mode image Submenu Setting SD PIXEL MAPPING Selects SD picture size (pixels) according to input signal format. • COMPOSITE&Y/C: Set to monitor the signal input through the LINE connector (VIDEO IN or Y/C IN connector). • RGB/COMPONENT: Set to monitor the signal input through the RGB/ COMPONENT connector. -
Page 28: Key Inhibit Menu
• 5:4 Troubleshooting • NORMAL • OVER • TALLY G • EXT SYNC This section may help you isolate the cause of a problem • BLUE ONLY and as a result, eliminate the need to contact technical • FULL support. •... -
Page 29: Specifications
Output Specifications LINE output connectors Y/C output 4-pin mini-DIN (1), Loop-through, with 75 ohms automatic terminal function Picture performance VIDEO output LCD panel a-Si TFT Active Matrix BNC type (1), Loop-through, with Picture size 21.5 type 75 ohms automatic terminal 477 ×... - Page 30 Design and specifications are subject to change without notice. Note Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS...
- Page 31 Video signal formats The unit is applicable to the following signal formats. Total Active Scanning System Frame rate Aspect ratio Signal standard lines lines format 575/50I (PAL) EBU N10 2:1 interlace 16:9/4:3 (PAL: ITU-R BT.624) 480/60I (NTSC) SMPTE 253M 2:1 interlace 16:9/4:3 (NTSC: SMPTE 170M) 576/50P...
- Page 32 When an optional input adaptor is connected, the unit is applicable to the following signal formats. When BKM-341HS is connected Input System Signal standard 575/50I SMPTE 259M 480/60I SMPTE 259M 1080/24PsF SMPTE 292M 1080/25PsF SMPTE 292M 1080/24P SMPTE 292M 1080/25P SMPTE 292M 1080/30P SMPTE 292M...
-
Page 33: Dimensions
Warning Dimensions • Be sure to set the tightening torque value to the following value. Torque value: 1.2±0.1 N·m Front • Make sure the tightening torque value is at this value. If the torque value is not appropriate, the mounting 515 ( 20 part may become damaged or the screws may become loosened, and in the worst case, it may cause injury or... -
Page 34: Licenses
216.4(8 source code. Unit: mm (inches) For details on the source code, contact your local Sony representative. However, be aware that Sony will not Mass Approx. 8.6 kg (18 lb 15 oz) answer questions concerning the data in the source code.