Pioneer PRO-1000HDI Service Manual page 124
Hide thumbs
Also See for PRO-1000HDI:
- Operating instructions manual (48 pages) ,
- Quick reference parts lists (12 pages)
Table of Contents
Advertisement
1
1
5
10
1
A
I N I T
5
10
15
16
B
8. FINAL SETUP: Factory preset values are set.
(See FINAL SETUP Details.)
9. VIDEO STANDARD: The peak occurrences of STANDARD (USER MENU / POWER CONTROL) in the video system signal is set.
(Table 1 setting in the following table.) Note: Please do not change settings during service.
10. PC STANDARD: The peak occurrences of STANDARD (USER MENU / POWER CONTROL) in the PC system signal is set.
(Table 2 setting in the following table.) Note: Please do not change settings during service.
11. VIDEO MODE1: The peak occurrences of MODE1 (USER MENU / POWER CONTROL) in the video system signal is set.
(Table 3 setting in the following table.) Note: Please do not change settings during service.
12. PC MODE1: The peak occurrences of MODE1 (USER MENU / POWER CONTROL) in the PC system signal is set.
(Table 4 setting in the following table.) Note: Please do not change settings during service.
C
POWER CONTROL
setting
13. EEP DATA READ: Data on each address of the EEPROM are displayed.
1
5
10
1
I N I T
D
5
10
E E P
D A T A
15
16
14. MASK1: To select the full mask. (Refer to "1 MASK1" .)
E
Note: The last setting for either MASK 1 or MASK 2 is stored in memory.
15. MASK2: To select the mask pattern. (Refer to "2 MASK2" .)
Note: The last setting for either MASK 1 or MASK 2 is stored in memory.
Notes on MASK 1 and MASK 2
• When any key is pressed, an OSD is displayed for two seconds, and during this period the full mask signal output is stopped.
• When the full mask is selected on the MASK selection menu, two seconds after the full mask is selected (with no key pressed during this
period,) the displayed OSD disappears, then full mask is displayed in turn.
• To release the mask setting, use "M00" of RS-232C Factory Adjustment mode or "MASK OFF" of Service Factory menu.
(The mask setting cannot be released with FULL MASK OFF of the Integrator menu or "FMN" of the RS-232C Factory Adjustment mode.)
F
124
1
2
15
20
25
30
# 1
–
U 2
–
I N 4 – 0 2 –
P
U L S
E
M
E T
E
R
S E T
?
Y E S
N O
Current Input Signal
VIDEO
STANDARD mode
Table1
MODE1
Table3
MODE2
PL6 (fixed)
15
20
25
30
# 1
–
U 2
–
I N 4 – 0 2 –
R E A D
:
1
0
F
F
PRO-1000HDI
2
3
35
40
: To select YES or NO
∗
SET
: When YES is selected, the SET DATA are stored
2
N T
in memory, and the initial display appears.
When NO is selected, NOW DATA is
maintained, and the initial display appears.
PC
Table2
Table4
35
40
: To select a digit (four digits) of an address
∗
2
N T
5∞ : To select numbers
SET : To shift to the next higher layer
Displayed data for each address are updated each time
the address is changed.
Display color : White (Selected address is yellow)
Half tone
-
8
0
3
4
: Blue (second line / 15th line for
each 5 to 36th columns)
4
Advertisement
Table of Contents
