Panasonic Toughbook CF-H1ADBBZCM Operating Instructions Manual page 22
Panasonic toughbook cf-h1adbbzcm: user guide
Hide thumbs
Also See for Toughbook CF-H1ADBBZCM:
- Reference manual (90 pages) ,
- Operating instructions manual (32 pages) ,
- Supplementary manual (3 pages)
Table of Contents
Advertisement
Troubleshooting (Basic)
n Shutting down
Windows.does.not.shut.
down.
n Display
No.display.
The.screen.is.dark.
The.screen.is.disordered.
During.Simultaneous.
display,.one.of.the.screens.
becomes.disordered.
The.external.display.does.
not.work.normally.
.
When.the.computer.starts.
up,.simultaneous.display.
becomes.active.
.
<Only.for.model.with.GPS>
The.cursor.cannot.be.
controlled.properly.
22
l. Remove.the.computer.from.the.Cradle.
l. Wait.one.or.two.minutes..It.is.not.a.malfunction.
l. When.using.an.external.display,
Ÿ. Check.the.cable.connection.
Ÿ. Turn.on.the.display.
Ÿ. Check.the.settings.of.external.display.
l. The.display.is.turned.off.by.the.power-saving.function..To.resume,.do.not.press.the.
direct.selection.keys,.but.press.any.other.key.like.
l. The.computer.entered.
sleep.(
(
)
.or.hibernation.by.the.power-saving.function..To.resume,.press.the.power.
switch.
.
l. The.screen.may.not.be.displayed.even.after.the.computer.resumed.from.standby.or.
hibernation..In.this.case,.press.the.power.switch.to.enter.standby.and.resume.the.
computer.again.
l. The.screen.might.be.darker.when.the.AC.adaptor.is.not.connected..Adjust.the.
brightness.by.using.Panasonic.Dashboard..As.you.increase.the.brightness,.battery.
consumption.increases.
You.can.separately.set.the.brightness.for.when.the.AC.adaptor.is.connected.and.when.
not.connected.
l. Changing.the.number.of.display.colors.and.resolution.may.affect.the.screen..Restart.the.
computer.
l. Connecting/disconnecting.an.external.display.may.affect.the.screen..Restart.the.
computer.
l. Simultaneous.display.cannot.be.used.until.Windows.startup.is.complete.(during.Setup.
Utility,.etc.).
l. When.using.the.Extended.Desktop,.use.the.same.display.colors.for.the.external.display.
as.those.used.by.the.LCD.
l. If.you.continue.to.experience.problems,.try.changing.the.display..
Right-click.on.the.desktop,.and.click.[Graphics.Properties].-.[Display.Devices].
l. If.the.external.display.does.not.support.the.power.saving.function,.it.may.not.work.normally.
when.the.computer.enters.the.power.saving.mode..Turn.off.the.external.display.
l. When.simultaneous.display.is.activated,.run.Panasonic.Dashboard.(è .
Manual."Panasonic.Dashboard").to.switch.the.display.
l. Operate.the.following.steps.
A S et [GPS] to [Disabled] in the [Advanced - Serial Port Configuration] of the Setup
Utility.
F10
B. . P ress.
and select [Yes] at the confirmation message, and press
The.computer.will.restart.
C. . L og.on.to.Windows.as.an.administrator.
D. . C lick.
(Start).and.input."c:\util\drivers\gps\GPSVista.reg".in.[Start.Search],.and.
press.
(Enter) .
E. . C lick.[Yes].and.click.[OK]..
The.computer.will.restart.
F2
Del
F. . P ress.
.or.
.while.[Panasonic].boot.screen.is.displayed.
G S et [GPS] to [Enabled] in the [Advanced - Serial Port Configuration].
F10
H. . P ress.
and select [Yes] at the confirmation message, and press
Ctrl
.
)./.standby..
.Reference
Enter
..
Enter
.
Advertisement
Table of Contents
Troubleshooting
