Where in a manufacturer’s service documentation, for example in circuit diagrams or lists of components, a symbol is used to indicate that a specific component shall be replaced only by the component specified in that documentation for safety reasons, the following symbol shall be used: MVH-08UBG/XEUW5...
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. MVH-08UBG/XEUW5...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted MVH-08UBG/XEUW5...
KEY PCB FLASH FLASH MAIN BOARD PCB TN LCD Radio Tuner LCD101 L L / R LINE OUT LINE OUT LCD Driver LINE OUT IC401 MPEG L/ R EN100 AMPLIFIER AUX IN CON102 CON103 CON103 U403...
M N B D P B PRE-GND oe not w norm repla the M gr wor normall repla mplete t w thout Front panel o not error r mplete t w thout Front panel LAMP LAMP(5V) MVH-08UBG/XEUW5...
• Turn the ignition switch OFF and – Replace the USB device. back to ON. • Disconnect the USB device. • Change t ERROR-23 USB device was not formatted properly. – Format the USB device with FAT12, FAT16 or FAT32. MVH-08UBG/XEUW5...
10 NC 3 FL- 11 MCU_RXD 4 FR- 12 NC 13 ACC 5 RL+ 14 B_REM 6 RR+ 7 RL- 15 BAT+ 8 RR- 16 DGND1 6. SERVICE MODE There is not information to be shown in this chapter. MVH-08UBG/XEUW5...
Main Frame Main Board Assy Board Assy. Fig.2 - Removing the Main Board PCB (Fig.3) Main Board PCB Remove the two screws. Straighten the tab at location indicated and then remove the Main Board PCB. Fig.3 MVH-08UBG/XEUW5...
Page 12
1. Attach the spike from the front side of the cabinet. Fig.6 2. Attach the spring to the lock as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.7 MVH-08UBG/XEUW5...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING MVH-08UBG/XEUW5...
Page 15
Polyethylene Bag Not used Not used Not used 127060000019 Polyethylene Bag Not used Not used Not used 127060000020 Polyethylene Bag CEG1160 CEG1160 CEG1160 CEG1160 Owner's Manual, Installation Manual Part No. Language 127075006696 English, Russian 127075006695 English, Spanish(Espanol), Portuguese(B) CRB4866 Portuguese(B) MVH-08UBG/XEUW5...
Page 17
121015000509 Screw 121106070013 Knob 121230005747000 Completed set without Front panel See Contrast table (2) Spike 121200001032000 (2) CONTRAST TABLE MVH-08UBG/XEUW5, MVH-08UB/XEUW5, MVH-85UB/XEES and MVH-88UB/XFBR are constructed the same except for the following: MVH-08UBG/ Mark Description MVH-08UB/XEUW5 MVH-85UB/XEES MVH-88UB/XFBR XEUW5 Detachable Assy...
10. SCHEMATIC DIAGRAM Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" . The > mark found on some component parts indicates MAIN BOARD PCB(MPEG/DECT) the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
11. PCB CONNECTION DIAGRAM SIDE A NOTE FOR PCB DIAGRAMS 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- MAIN BOARD PCB gram.
The expression of the unit in this manual is shown by u instead of . Please do not make a mistake. Circuit Symbol and No. Part No. Unit Number : Unit Name : MAIN BOARD PCB MISCELLANEOUS Power Amp IC PA2032A Poly Switch 144800010012 EN100 Rotary Encoder 121658000198 MVH-08UBG/XEUW5...