Advertisement
Operation
Timer ON/OFF Function,(Set clock correctly before starting TIMER operation)
Timer ON-OFF Function
1.Unit start
B
After unit starts,select your desired operation mode(Operation mode
will be displayed on LCD)
2.TIMER mode selection
Press TIMER button on the remote controller to changeTIMER mode.
Every time the button is pressed,display of TIMER mode changes as
follows:
OFF
ON
TIMER ON
TEMP
ON
Then select TIMER mode as needed
OFF
S W I N G
FAN
3.Time setting
1
Press time button
MODE
SLEEP
Every time the button is pressed,time increases an hour.If the button
HEALTH
FRESH
is kept pressed,time will changes quickly.
Every time the button is pressed,time decreases an hour.If the button
CLOCK
SET
R
is kept pressed,time will changes quickly.It can be adjusted with in
4
TIMER
3
HIGH/SO
6
2
H IG
12 hours at will. AM refers to morning and PM refers to afternoon.
FILTER
5
7
FIL
4.Timer confirming
R
HEAT
After time setting ,press SET button to confirm time.
LIGHT
LOCK
RESET
CODE
5.Canel TIMER mode
After replacing batteries or if apower failure occurs,TIMER setting must be reset.
Remote controller has memory function.When you use TIMER mode next time,just press SET
button after mode selection if timer setting is the same as the previou sone.
Auto restart (to be applied for a necessary situation) :
After the Auto restart is set, if power failure suddenly occurs while the air conditioner is
working, it will resume the previous working state when the power is supplied again.
Setting Method: When the wire remote controller is on (excluding timer mode and fan mode), press
the "SWING" button on the wire remote controller 10 times within 5 seconds, and after the buzzer
rings 4 times, the air conditioner will enter the state of power failure compensation.
Cancel Method: Press the "SWING" button on the wire remote controller 10 times within 5 seconds,
and after the buzzer rings 2 timer, the Auto restart mode will be cancelled.
Notes: When a power failure suddenly occurs during the air conditioner is working after the Auto restart
is set, if the air conditioner will not be used for a long time, please cut off the
power supply to prevent its operation from being resumed after the power is supplied again, or press
the "Switch On/Off" button after the power comes again.
OFF
blank
TIMER OFF
5
Parts and Functions
Remote controller
28
27
29
26
30
25
31
B
A
24
32
23
33
22
34
A
U
T
21
O
35
OFF
M
D
20
36
19
1
TEMP
ON
2
18
OFF
SWING
FAN
3
17
MODE
SLEEP
4
16
HEALTH
FRESH
15
5
CLOCK
SET
14
6
TIMER
HIGH/SO
13
7
FILTER
HEAT
37
8
RESET
CODE
LIGHT
LOCK
12
9
11
10
1.TEMP Setting Button
(Used to set temperature. Setting ranges:
16 C to 30 C)
2.SWING Button
If you press this button once, auto swing will be
activated.
If you press this button again, the louver will fix
in the present position.
3.Power ON/OFF Button
Used for unit start and stop
After power on, the LCD of remote controller will
display the previous operation state (except for
TIMER,SLEEP and SWING state).
4.Operation MODE
Used to select operation mode.
Every time you press MODE button, operation mode
changes according to following sequence:
The function of code A
FAN
AUTO
COOL
DRY
HEAT
The function of code B
DRY
HEAT
COOL
5.HEALTH Button
6.CLOCK Button
Used to set correct time.
7.TIMER Button
Used to select TIMER mode:TIMER ON,TIMER OFF.
(Note: if time of TIMER ON is the same as TIMER OFF)
8. FILTER Button
Used to set up/down function of filter.
9.CODE Button
Used to select Code A or B, this manual is for code B.
10.RESET Button
Press this button by using a sharp article to resume the correct
operation of the remote controller in case of need, i.e. for
example in case of malfunctions due to electromagnetic
disturbance.
11.LIGHT Button
Used to light the control panel (only for cabinet unit)
12.LOCK Button
Used to lock operation button and LCD display contents: by
pressing this button, other buttons comes out of function and
lock state display appears; if you press it again, lock state
will be no more active and lock state display will disappear.
13.HOUR Adjustment
Used to set clock and timer setting
14.HIGH/SO Button
Used to select HIGH or SOFT operation.
15.SET Button
Used to confirm TIMER and CLOCK settings when
or cooling. heating
16.FRESH Button
Used to set fresh mode, the unit will draw in fresh air.
17.SLEEP Button
(The clock must be corrected before setting sleep function)
Used to set sleep mode.
18.FAN Button
Used to select fan speed:LOW,MID,HIGH,AUTO.
19.TIMER OFF Display
20.TIMER Display
21.FILTER Display
When the filter need be cleaned, the sign will
appear automatically.
22.TEMPERATURE Display
23.AUTO SWING Display
24.HIGN/SO Run Display
2
Hide quick links:
Advertisement
