Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Product information is subject to change without notice. - Weight ± 4.92 kg For detailed product information,please visit • with TV stand: www.philips.com/support Width 732.5 mm - Height 492 mm - Depth 179.2 mm - Weight ± 5.05 kg 43PFT5102 Display •...
Cable dressing (49" 5102 series) 3.2 Assembly/Panel Removal 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand. 2. Take the stand bracket out from the set. 3.2.2 IR board Control Unit Unplug the connector from the SSB.
Page 8
3.2.3 Rear Cover Warning: Disconnect the mains internal cable(MB to IR board) before removing the rear cover. 1. Remove fixation screws [2] and [3] that secure the back cover.. 2. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set. 3.2.4 Keyboard Control Unit Release the connector [1] from the SSB Board.
Page 9
3.2.5 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. 1. Release the clips from the LVDS connector that connect with the SSB[1]. Caution: be careful, as these are very fragile connectors! 2.
Page 10
3.2.6 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 12
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 13
Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return” button. Do not allow the display to time out between entries while keying the sequence. After entering the Factory mode, we can see many items displayed, use the UP/DOWN keys to display the next/previous menu items Factory mode overview How to Exit the Factory mode Use one of the following methods:...
Page 14
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. ...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). 4. Switch off the TV and Insert the USB memory stick that contains the software update files in one of the TV’s USB 2.0 ports. Note: It contains USB3.0 port, if connect on it, the software may can’t be detected.
Page 16
Step 2: F/W Upgrade 1. Press [Quick settings], then Choose [Update Software] in the Settings menu 2. Choose [Local Updates], then press OK. Select the file that you downloaded and press OK 4. Choose [Update], then choose [Start] on following step...
Page 17
5. Upgrade in progress Step 3: Check the SW version 1. After burning software, TV will restart 2. Press “123654”, enter Customer Service Mode to check if the software version is correct Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 18
5.2.2 How to Read the Error Buffer You can read the error buffer in below ways: • On screen via the SAM/CSM (if you have a picture). Example: – ERROR: 000 000 000 000 000: No errors detected – ERROR: 013 000 000 000 000: Error code 13 is the last and only detected error –...
Page 19
• By using the CLEAR command in the Factory mode: • By using the following key sequence on the remote control transmitter: “062599” directly followed by the OK button. • If the contents of the error buffer have not changed for 50 hours, the error buffer resets automatically. Note: If you exit SAM by disconnecting the mains from the television set, the error buffer is not reset.
6. Circuit Descriptions 6.1 Introduction The TPM17.7A LA is a new chassis launched in AP in 2017. The whole range is covered by MT5800LUEJ platform. The major deltas versus its predecessor support NTSC; PAL-M; PAL-N AND ISDB-T with also multi-media, CEC, ARC, MHL, SPDIF functionality. The TPM17.7A LA chassis comes with the following stylings: series xxPHT5102/xx ...
Page 21
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 22
PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller). PSDL stands for a Power Supply for Direct-view LED backlight with 2D-dimming. 6.3 DC/DC Converters The on-board DC/DC converters deliver the following voltages(depending on set execution): •...
Page 23
6.3.2 Power layout SSB (For 715G8251) 6.4 Front-End Analogue and DVB-C,DVB-T2; reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER LATAM ST53WS-13-E • SCALER MT5800LUEJ HSFBGA-597 Processor Below find a block diagram of the front-end application for DVB-C part. MT5800...
Page 24
6.4.2 DTB-T2 part The Front-End for DVT part consist of the following key components: • TUNER LATAM ST53WS-13-E • SCALER MT5800LUEJ HSFBGA-597 Processor • DEMODULATOR SI2180-B60-GMR QFN-48 Below find a block diagram of the front-end application for DTV part. Si2180 MT5800 6.5 HDMI Refer to below for the application.
Page 25
6.6 Video and Audio Processing - MT5800LUEJ The MT5800LUEJ is the main audio and video processor (or System-on-Chip) for this platform. It has the following features: 1. Worldwide multi-standard analog TV demodulator 2. demodulators 3. Powerful quad core CPU 4. 3D graphic support OpenGL ES 2.0 5.
Page 46
8.6 E 715G7088 Keyboard control panel 8-6-1 Key...
Page 47
9. Styling Sheets 9.1 5102 series 32" Pos NO. Description Remark 0030 BEZEL 0040 REAR COVER 0064 PCB_FRAME 050R STAND BASE R 050L STAND BASE L 1050 PANEL 1176 Remote Control No Display 1053 MIAN BOARD 1054 POWER BOARD 1056...