Philips 40PFL4908/F7 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. LCD TV
  5. 40PFL4908/F7
  6. Service manual

Philips 40PFL4908/F7 Service Manual

40” lcd tv
Hide thumbs Also See for 40PFL4908/F7:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual
TYPE A
40PFL4908/F7
40PFL4908/F8
TYPE B
40PFL4708/F7
40PFL4708/F8
This service manual contains information of different types of models.
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
Make sure to refer to the section describing your model.
© 2013 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
PHILIPS
(Serial No.: DS1)
PHILIPS
(Serial No.: XA1)
PHILIPS
(Serial No.: DS1)
PHILIPS
(Serial No.: XA1)
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis PL13.13
Contents
40" LCD TV
130529

Advertisement

Table of Contents
loading

Related Manuals for Philips 40PFL4908/F7

Summary of Contents for Philips 40PFL4908/F7

  • Page 1 40” LCD TV chassis PL13.13 Service Manual Contents TYPE A 40PFL4908/F7 PHILIPS (Serial No.: DS1) 40PFL4908/F8 PHILIPS (Serial No.: XA1) TYPE B 40PFL4708/F7 PHILIPS (Serial No.: DS1) 40PFL4708/F8 PHILIPS (Serial No.: XA1) This service manual contains information of different types of models.
  • Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions .

  • Page 4: Specifications

    SPECIFICATIONS < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range TV.ch.4 ±2.3 ±2.1 TV.ch.4 dBμV 2. Synchronizing Sens. CA.ch.31 dBμV CA.ch.87 dBμV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 7 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View Bottom View 1.
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS Screw Torque Specification Step/ Fig. Loc. Part Removal Note Ref. Part Tightening Part Name Number Torque SCREW P-TIGHT Rear Cover D1 2(S-3), 10(S-4) L9 GBHP3120 (3X12 BIND HEAD+ 5.2±0.9lb·in Power BLK) 5(S-5), CN601, Supply SCREW S-TIGHT CN501, CN1001 L23 GBJS3060 6.1±0.9lb·in (M3X6 BIND HEAD+)
  • Page 14 Important precautions concerning the • After replacing the Front Cabinet or Function CBA Unit, check the operational sensitivity of the touch LCD Panel Assembly: sensor to make sure it functions normally. 1. When you disassemble/re-assemble the Front • Make sure to replace the Decoration Plate to a new Cabinet or Function CBA Unit one when replacing the Front Cabinet.
  • Page 15 [5] Digital Main CBA Unit Type A (S-6) Jack Holder Type B (S-5) (S-6) Jack Holder [4] Power Supply CBA Fig. D2 [9] LCD Panel Assembly [7] Speaker Shield Plate [6] Stand Bracket [7] Speaker (S-7) [8] Function CBA Unit Leading Edge Cover Fig.
  • Page 16 [10] X-PCB Cover Hook [11] Front Cabinet Hook Decoration Plate (S-8) Hook Hook (S-9) Fig. D4 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Front Cabinet. : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the X-PCB Cover.
  • Page 17 TV Cable Wiring Diagram To LCD Panel To LCD Panel Assembly Assembly Digital Main Power Supply CBA CBA Unit CN1001 CN3906 CN3013 CN3601 CN501 CN3602 CN601 CN3105 CN3801 CN3101 To AC Cord Function CBA Unit To Speaker CN4001 *1: TYPE A *2: TYPE B Fig.

  • Page 18: Electrical Adjustment Instructions [Type A]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 19 The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel 6. Press [MENU] button. The internal Raster signal or Digital Main CBA. appears in the screen.
  • Page 20 13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. Internal (Single) 14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR”...

  • Page 21: [Type B]

    [TYPE B] 1. Purity Check Mode General Note: “CBA” is abbreviation for This mode cycles through full-screen displays of red, “Circuit Board Assembly.” green, blue, and white to check for non-active pixels. 1. Enter the service mode. Note: Electrical adjustments are required after replacing circuit components and certain 2.
  • Page 22 The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears performed when replacing the LCD Panel in the upper right of the screen as shown below.) or Digital Main CBA. 2.

  • Page 23: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

  • Page 24: Firmware Renewal Mode [Type A]

    FIRMWARE RENEWAL MODE [TYPE A] Update file selection screen appears as follows. (Files included in the USB storage device are displayed. Equipment Required " * " differs depending on the models. 1. USB storage device *****_******.upg Select an upgrade file 2.

  • Page 25: [Type B]

    [TYPE B] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: TVNB1012_00_PG_XX91_BA0.bin) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_”...
  • Page 26 Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB1012_00_PG_XX91_BA0.bin) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_”...

  • Page 27: Troubleshooting

    TROUBLESHOOTING [Power Supply Section] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F602) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C607, C612, D601, D602, D603, D604, D605, D606, D607A, D608, D609A, D621, D623, Q601, Q602, Is the P-ON+21V line voltage normal?
  • Page 28 FLOW CHART NO.5 P-ON+21V is not output. Check D650, D651, D652, D659, C651, C652, C653, C667, C668 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. FLOW CHART NO.7 [TYPE A] AL+3.3V is not output. [TYPE B] AL+3.3V is not output.
  • Page 29 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Replace the Function CBA Unit. Replace the Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) Check AL+3.3V line and repair it if defective.
  • Page 30 [Audio Signal Section] FLOW CHART NO.1 Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]> See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]> Replace the Digital Main CBA Unit. PL13.13ATR...

  • Page 31: Block Diagrams [Type A]

    BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL13.13ABLS...
  • Page 32 2. Video/Audio Block Diagram PL13.13ABLVA...
  • Page 33 3. Digital Signal Process Block Diagram PL13.13ABLD...
  • Page 34 4. LED Backlight Drive Block Diagram PL13.13BLBD...
  • Page 35 5. Power Supply Block Diagram PL13.13ABLP...

  • Page 36: [Type B]

    [TYPE B] 1. System Control Block Diagram PL13.13BBLS...
  • Page 37 2. Video/Audio Block Diagram PL13.13BBLVA...
  • Page 38 3. Digital Signal Process Block Diagram PL13.13BBLD...
  • Page 39 4. LED Backlight Drive Block Diagram PL13.13BLBD...
  • Page 40 5. Power Supply Block Diagram 9-10 PL13.13BBLP...

  • Page 41: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 42 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 43 Power Supply 1 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 2.5A, 250V fuse.
  • Page 44 Power Supply 2 Schematic Diagram C1026 100P/500V CONTINUE D1001 L1001 POWER 1 SK210TD 22uH P-ON+21V R1006 BACKLIGHT-ADJ C1008 C1010 C1018 C1014 C1012 R1034 R1005 47/100V 47/100V 1/100V 1/100V OPEN 510K PROTECT3 C1001 C1002 C1003 C1004 C1005 C1006 BACKLIGHT-SW R1035 330/25V 330/25V OPEN 430K...
  • Page 45 Function Schematic Diagram C4054 TO DIGITAL MAIN R4052 R4063 6.8K OPEN CBA UNIT CN3101 R4061 CN4001 or CN3105 OPEN R4062 1 AL+3.3V 2 P-ON+5V 3 LIGHT RS4051 RS-272 4 LED1 D4051 (REMOTE SENSOR) R4055 R4059 SML813WBC8W1 OPEN OPEN 5 REMOTE IC4051 POWER PH5502B2NA1-E4...
  • Page 46 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE (NO CONNECTION) CN3905...
  • Page 47 Digital Main 2 Schematic Diagram [TYPE A] CONTINUE DIGITAL 7 P-ON+21V R3942 P-ON+3.3V OPEN CONTINUE R3952 D3905 DIGITAL 2 Q3905 OPEN OPEN OPEN LCD+12V/+21V C3996 OPEN D3906 OPEN IC3901 R3899 R3550 MP1472GJC452Z OPEN 6.8K (+12V REG.) C3946 0.047 R3897 C3949 OPEN R3891 TO LCD PANEL...
  • Page 48 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(2/7) MN2WS0270EA DIGITAL MAIN CBA UNIT...
  • Page 49 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(3/7) MN2WS0270EA DIGITAL SIGNAL PROCESS...
  • Page 50 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 7 TU3001...
  • Page 51 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. 10-11 PL13.13ASCD6...
  • Page 52 Digital Main 7 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 1 P-ON+21V...
  • Page 53 Digital Main 8 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT R3144 CONTINUE...
  • Page 54 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 5...
  • Page 55 Digital Main 2 Schematic Diagram [TYPE B] CONTINUE DIGITAL MAIN CBA UNIT DIGITAL 1 PANEL-VCOM-PWM CELL-PWR-CTRL R3039 LCD+12V OPEN R3035 OPEN CN3001 (NO CONNECTION) 31 LCD+12V C3514 C3513 30 LCD+12V OPEN OPEN 29 LCD+12V R3028 28 GND OPEN R3037 OPEN 27 VCOM-PWM C3918 C3921...
  • Page 56 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(2/5) R3231...
  • Page 57 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. IC3001(3/5) MSD8200DS-S1 DIGITAL MAIN CBA UNIT...
  • Page 58 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 3...
  • Page 59 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. TU3901 (TUNER UNIT) DIGITAL MAIN CBA UNIT IC3001(5/5)
  • Page 60 Power Supply CBA Top View Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, CAUTION ! when troubleshooting this type of power supply circuit, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 61 Power Supply CBA Bottom View Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, CAUTION ! when troubleshooting this type of power supply circuit, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 62 WIRING DIAGRAM [TYPE A] 11-1 PL13.13AWI...

  • Page 63: [Type B]

    [TYPE B] 11-2 PL13.13BWI...

  • Page 64: Exploded Views [Type A]

    EXPLODED VIEWS [TYPE A] LCD1 CL3011 40PFL4908/F7(Serial No.:DS1) Digital Main CBA Unit Power Supply CBA CL3701 Function CBA Unit AC601 CL3801 CL3101 SP3801 SP3802 See Electrical Parts List for parts with this mark. SSK1 SNA1 SBA1 SSK2 12-1 PL13.11_A CEX...

  • Page 65: [Type B]

    [TYPE B] LCD1 CL3011 40PFL4708/F7(Serial No.:DS1) Digital Main CBA Unit Power Supply CBA CL3701 Function CBA Unit AC601 CL3801 CL3101 SP3801 SP3802 See Electrical Parts List for parts with this mark. SSK1 SNA1 SBA1 SSK2 12-2 PL13.11_A CEX...
  • Page 66 Packing 40PFL4708/F7(Serial No.:DS1), 40PFL4908/F7(Serial No.:DS1) SSK1 SSK2 SNA1 Tape SBA1 Packing Tape 40PFL4708/F8(Serial No.:XA1), 40PFL4908/F8(Serial No.:XA1) Packing Tape F R O F R O Some Ref. Numbers are not in sequence. Packing Tape 12-3 PL13.13_PEX...

  • Page 67: Parts List

    TYPE A PARTS LIST [40PFL4908/F7 (Serial No.: DS1)] Mechanical Parts LCD PANEL ASSEMBLY PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Ref. No. Description Part No. Before replacing any of these components, read LCD1#...
  • Page 68 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a POWER SUPPLY CBA # have special characteristics important to safety. Ref. No. Description Part No. Before replacing any of these components, read POWER SUPPLY CBA A3RP0MPW-002 carefully the product safety notice in this service Consists fo the following manual.
  • Page 69 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 560 Ω DIODES R621 RRXA561HH013 RES CHIP 1608 1/10W 0 Ω R622 RRXA000HH014 D601 DIODE 1N5406BH NDL1001N5406 RES CHIP 1608 1/10W J 10k Ω R623 RRXA103HH013 D602 DIODE 1N5406BH...
  • Page 70 Ref. No. Description Part No. RES CHIP 1608 1/10W 0 Ω R1040 RRXA000HH014 RES CHIP 1608 1/10W F 100 Ω R1041 RTW1000HH008 RES CHIP 1608 1/10W F 100 Ω R1042 RTW1000HH008 RES CHIP 1608 1/10W 0 Ω R1047 RRXA000HH014 MISCELLANEOUS HEAT SINK PNL A31T0UH 1EM439707 BC601...
  • Page 71 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. A15#...
  • Page 72 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A3RPAMMA-002 2013/04/09 13-6 A3RPAEL.fm...
  • Page 73 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. REAR COVER A31T0UH...
  • Page 74 RES CHIP 3216 1/4W J 2.2 Ω R688 RRX42R2HH034 RES CHIP 3216 1/4W J 2.7 Ω R689 RRX42R7HH034 R690# Not used Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A31P2MMA-001 CN3701 Not used IC3001...
  • Page 75 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. REAR COVER A31T0UH...
  • Page 76 RES CHIP 3216 1/4W J 2.2 Ω R688 RRX42R2HH034 RES CHIP 3216 1/4W J 2.7 Ω R689 RRX42R7HH034 R690# Not used Different parts from the original model 40PFL4908/F7 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A31PAMMA-002 CN3701 Not used IC3001...

  • Page 77: Revision History

    REVISION HISTORY Chassis PL13.13 • 2013/03/19 40PFL4908/F7 (Serial No.: DS1) Added • 2013/04/30 40PFL4708/F8 (Serial No.: XA1) Added • 2013/05/29 40PFL4908/F8 (Serial No.: XA1) Added • 2013/05/29 40PFL4708/F7 (Serial No.: DS1) Added 14-1 PL13.13REV...
  • Page 78 COMPARISON LIST OF MODEL NAMES Chassis PL13.13 40PFL4908/F7 (DS1) A3RP0UH TYPE A 40PFL4908/F8 (XA1) A3RPAMA TYPE A 40PFL4708/F7 (DS1) A31P2UH TYPE B 40PFL4708/F8 (XA1) A31PAMA TYPE B PL13.13COM...

This manual is also suitable for:

40pfl4908/f840pfl4708/f740pfl4708/f8

Table of Contents