Page 1
DVP-S7700 RMT-D107A SERVICE MANUAL US Model Canadian Model SPECIFICATIONS CD/DVD PLAYER MICROFILM...
Page 2
SONY PARTS WHOSE PART NUMBERS APPEAR AS DE FONCTIONNEMENT. NE REMPLACER CES COM- SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
TABLE OF CONTENTS Section Title Page Section Title Page Service Note ................4 CN-112, DR-87, FL-107, FR-159, PW-119 Printed Wiring Boards ........4-63 GENERAL CN-112, DR-87, FL-107, FR-159, PW-119 Schematic Diagrams ........4-65 PS-420 Printed Wiring Board ........4-67 This Player Can Play the Following Discs ....1-1 PS-420 Schematic Diagram ..........
SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Upper Case (Page 2-1) MB-84 Front Panel AU-218 Board Section Board (Page 2-1) (Page 2-1) (Page 2-2) MD Block Door Open/ Ass’y Close Motor (Page 2-2) (Page 2-1) TK-47 Tray...
Page 5
2. DISK REMOVAL PROCEDURE 3. HOW TO SERVICE MB-84 (SIDE B) BOARD (at POWER OFF) 1) Remove the case from the set. (Refer to 2-1) 2) Remove the cover (upper). (Refer to 2-3) 3) Set the MB-84 board as shown in Fig. 3. 2-1.
Page 6
4. NOTE ON MOUNTEING SLED MOTOR 1) Push the sled motor ass’y 1 toward direction A. (See Fig. 4) 2) Tighten two screws 2 (M1.7 × 2.5). 1 Sled motor ass’y 2 Two screws (M1.7 × 2.5) Fig. 4 3) Raising the MD block ass’y 3 90 º with the side down. confirm that the optical pick-up 4 falls by self weight.
Page 7
5. REPLACING OPTICAL PICK-UP 3) In handling the KHS-180A (RP), do not touch inhibited parts shown in Fig. 7, but grip the slide base bearing and U-shaped guide. 5-1. Handling 1) A red laser diode for DVD requires more attention to static Slide base bearing electricity than general infrared laser diodes for CD.
Page 8
6. NOTE ON ASSEMBLING MECHANICAL DECK 6-1. Application of Grease 1) Grease must be applied if the following parts were replaced. (See Fig. 8) Note 1: Recommended grease is Foil KG-70MP. Note 2: In applying grease, take care not to allow grease to stick to other parts (particularly, rubber belt, spindle motor, and optical pick-up) Base unit holder...
Page 9
6-2. Cleaning Spindle Motor Turntable 6-4. Deformation of Insulator 1) Remove the tray. (Refer to 2-7) 1) Assemble the spindle base into the base unit. 2) Clean the spindle motor turntable if disc antiskid rubber (black) 2) Lock with 4 shoulder screws. (See Fig. 11) is dirty.
Page 10
6-6. Note on Mounting TK-47 Board 1) Align two bosses. (See Fig. 13) 2) Align four tabs. (See Fig. 13) 3) Fix the board securely with 3 screws (BV3 × 10). (The sensor will not function normally if the board floats up.) Three screws (BV3 ×...
DVP-S7700 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. UPPER CASE REMOVAL 2-3. DOOR OPEN/CLOSE MOTOR REMOVAL 4 Upper case 3 Door open/close motor CN-112 board 1 Two tapping screws 2 Four tapping screws 1 Flat cable (CN451) 2 Two screws...
2-13. INTERNAL VIEWS Skew motor ass’y (tilt) X-3947-138-1 Optical pick-up Optical pick-up (KHS-180A/J1N) Sled motor ass’y (KHS-180A/J1N) Sled motor ass’y 8-820-005-02 X-3947-137-1 8-820-005-02 X-3947-137-1 DC motor (spindle) 1-698-944-11 Motor (loading) 1-698-942-21 DC motor (spindle) 1-698-944-11...
DVP-S7700 3-3. SIGNAL PROCESS BLOCK DIAGRAM MB-84 BOARD (2/6) (SEE PAGE 4-19, 4-41) IC207 IC201 IC202 24 SCLK 16M SDRAM 16M SDRAM 25 SIN SCLKO R OUT CGCSO G OUT IC810 B OUT I OUT 4M DRAM 11 EVEN SYSTEM CONTROL (SEE PAGE 3-9, 10) H SYVC SDQM, WE, CAS, RAS, CS1, CS2, SDQM, SDCLK...
DVP-S7700 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING For schematic Diagram: • Caution when replacing chip parts. BOARDS AND SCHEMATIC DIAGRAMS. New parts must be attached after removal of chip. (In addition to this, the necessary mote is printed Be careful not to heat the minus side of tantalum capacitor, in each block.) because it is damaged by the heat.
DVP-S7700 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS There are few cases that the part isn't mounted in this model is printed on this diagram. TK-47 (RF, SERVO) PRINTED WIRING BOARD – Ref. No.: TK-47 board; 3,000 series – TK-47 BOARD(SIDE A) TK-47 BOARD (SIDE A) CN001...
Page 41
DVP-S7700 MB-84 (SIGNAL PROCESS), FG-43 (SLED) PRINTED WIRING BOARDS There are few cases that the part isn't mounted in this model is printed on this diagram. – Ref. No.: MB-84 board; 2,000 series, FG-43 board; 1,000 series – MB-84 BOARD(SIDE A) FG-43 MB-84 BOARD (SIDE A) BOARD...
DVP-S7700 MB-84 (BIAS) SCHEMATIC DIAGRAM • See page 4-15 to 4-18 for printed wiring board. – Ref. No.: MB-84 boards; 2,000 series – Note: Note: Les composants identifiés par The components identi- une marque ! sont critiques fied by mark ! or dotted line with mark ! are criti- pour la sécurité.
DVP-S7700 AU-218 (AUDIO) PRINTED WIRING BOARD There are few cases that the part isn't mounted in this model is printed on this diagram. – Ref. No.: AU-218 board; 3,000 series – AU-218 BOARD(SIDE A) 1-671-910- (11) POWER BLOCK (HS-930SU) (SWITCHING REGULATOR) FR-159 FG-43 (FUNCTION SWITCH)
Page 58
DVP-S7700 AU-218 BOARD(SIDE B) LINE OUT DIGITAL OUT VIDEO AUDIO COAXIAL S-LINK OPTICAL S VIDEO OUT 1-671-910- (11) AU-218 BOARD (SIDE B) IC206 CN201 CN203 IC207 CN204 IC208 CN205 IC209 IC210 D201 D202 Q201 Q202 D203 Q203 D204 Q204 D205 D206 Q205 D207...
Page 59
DVP-S7700 AU-218 (AUDIO 1) SCHEMATIC DIAGRAM • See page 4-47 to 4-50 for printed wiring board. – Ref. No.: AU-218 board; 3,000 series – AUDIO 1 AU-218(1/3) 4-51 4-52...
Page 60
DVP-S7700 AU-218 (AUDIO 2) SCHEMATIC DIAGRAM • See page 4-47 to 4-50 for printed wiring board. – Ref. No.: AU-218 board; 3,000 series – AUDIO 2 AU-218(2/3) 4-53 4-54...
Page 61
DVP-S7700 AU-218 (VIDEO BUFFER) SCHEMATIC DIAGRAM • See page 4-47 to 4-50 for printed wiring board. – Ref. No.: AU-218 board; 3,000 series – • Waveforms 1 IC209 !∞ 1.1 Vp-p (H) 2 IC209 !£ 1.0 Vp-p (H) 3 IC209 0 0.7 Vp-p (H) VIDEO BUFFER AU-218 (3/3)
DVP-S7700 YS-18 (COMPONENT VIDEO) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: YS-18 board; 1,000 series – POWER BLOCK (HS-930SU) (SWITCHING REGULATOR) There are few cases that the part isn't mounted in this model is printed on this diagram. FR-159 FG-43 (FUNCTION SWITCH)
Page 63
DVP-S7700 FP-60 (FL DRIVER), HP-119 (HEAD PHONE) PRINTED WIRING BOARDS – Ref. No.: FP-60 board, HP-119 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. FP-60 BOARD(SIDE A) FP-60 BOARD (SIDEA) CN201 A-10...
Page 65
DVP-S7700 CN-112 (DOOR MOTOR), DR-87 (DOOR SENSOR), FL-107 (FUNCTION SWITCH), FR-159 (FUNCTION SWITCH), PW-119 (IR/POWER SWITCH) PRINTED WIRING BOARDS – Ref. No.: CN-112 board, DR-87 board, FL-107 board, FR-159 board, PW-119 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. FR-159 FL-107 BOARD(SIDE A)
DVP-S7700 CN-112 (DOOR MOTOR), DR-87 (DOOR SENSOR), FL-107 (FUNCTION SWITCH), FR-159 (FUNCTION SWITCH), PW-119 (IR/POWER SWITCH) SCHEMATIC DIAGRAMS – Ref. No.: CN-112 board, DR-87 board, FL-107 board, FR-159 board, PW-119 board; 1,000 series – Note: Note: The components identi- Les composants identifiés par fied by mark ! or dotted une marque ! sont critiques line with mark ! are criti-...
Page 67
DVP-S7700 PS-420 (AUDIO POWER) PRINTED WIRING BOARD – Ref. No.: PS-420 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. PS-420 PS-420 BOARD(SIDE B) BOARD(SIDE A) (12) (12) 1-671-906- 1-671-906- POWER BLOCK...
Page 68
DVP-S7700 PS-420 (AUDIO POWER) SCHEMATIC DIAGRAM – Ref. No.: PS-420 board; 1,000 series – Note: Note: The components identi- Les composants identifiés par fied by mark ! or dotted une marque ! sont critiques line with mark ! are criti- pour la sécurité.
DVP-S7700 POWER BLOCK (HS-930SU) (SWITCHING REGULATOR) PRINTED WIRING BOARD – Ref. No.: HS-930SU board; 4,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. POWER BLOCK (HS-930SU) (SWITCHING REGULATOR) FR-159 FG-43 (FUNCTION SWITCH) (SLED)
DVP-S7700 SECTION 6 TEST MODE 6-1. Starting up Test Mode Syscon Diagnosis IF con Ver. 0.620 (9315) With the DVP-S7700 turned off, press [TITLE], [CLEAR], and SYScon Ver. 0.400 (0000) [POWER] keys on the Remocon in this order, and the Test mode →Enter item No.[02] ;...
6-3. Error Display (3) Destination Setting (3-2) Destination setting Check In case of an error, the error code and information are displayed as shown in Figure 7. I/O port read Syscon Diagnosis Error:Not detected IF con Ver. 0.620 (9315) SYScon Ver. 0.400 (62ED) →Check item name RAM Check The destination setting port (I/O) is read, and displayed with hex.
Page 76
(5-4) Servo DSP (IC506) Download (6) Data Source DSP (IC506) code area ROM/RAM discrimination (6-2) Register in ARP (IC806) RAM: Program download → Revision data read Register write → Register read matching check ROM: Revision data read Error 04: Data read error Error 05: Write/read data mismatch error 13: DSP (IC506) data not ready Data from “0x00”...
Page 77
(6-6) Register in Decrypt IC (IC811) (7-3) Reset Line in AV Decoder (IC203) Register write → Register read matching check Register write → Hard reset → Register read matching check Error 05: Write/read data mismatch error Error 02: Reset error 05: Write/read data mismatch error 0x00 –...
Page 78
(7-6) Connection from ARP (IC806) to AV Decoder (IC203) (8-4) Video Encoder (IC252) Vsync ROM data → ARP (IC806) → Decrypt (IC811) → AV Decoder CPU measures the Video Encoder (IC252) Vsync interrupt cycle. (IC203) Error 41: Vsync interruption is not detected Error 04: Data read error 42: Vsync interrupt cycle error 05: Write/read data mismatch error...
Page 79
(8-8) S Terminal DC Check (9-5) Audio Digital Output ROM audio data → ARP (IC806) → AV Decoder (IC203) → Digi- Color bar output by NTSC Encoder in Video Encoder (IC252) tal audio I/F output Error 11: Serial transfer error Error 10: ARP (IC806) →...
Page 80
g Error Codes in Diagnostic Test (9-8) Dual DAC (Serial) ROM audio data → ARP (IC806) → AV Decoder (IC203) → 2ch 01: Mode not supported is selected DAC (IC215) → Analog audio output (Attenuation) 02: Reset error 03: Data write error Error 10: ARP (IC806) →...
6-5. Drive Auto Adjustment The tray opens after the [ENTER] key is pressed and the initial- ization is finished. Then, place the DVD_SL disc for adjustment. Press the [ENTER] key to start adjustment. During adjustment, The drive can be automatically adjusted, except disc change and the tangential skew adjustment screen is displayed.
Page 82
Drive Automatic Adjustment Flowchart DVD_SL Loading adjustment Adj. disc selection FOK Check STOP Tracking ON Select “ALL” Sled ON AGC ON CLVA EEPROM Default Set Lock Check STOP Hydet Init Sled Init Go To Home Position Auto Loop Filter Offset Auto Focus Offset Auto Tilt Offset Auto Focus Offset...
Page 83
DVD_SL adjustment adjustment Auto Loop Filter Offset FOK Check STOP Auto Focus Offset Auto Tilt Offset Auto Focus Offset Auto Focus Gain Auto Tracking Offset Auto Tracking Gain Auto EQ. Auto Loop Filter Offset Pull in Memory FOK Check STOP Jitter Check Tracking ON Sled ON...
Page 84
DVD_DL DVD_DL adjustment adjustment Disc Type Check FOK Check STOP Tracking ON LD ON Sled ON Spindle start CLVA Tilt ON Focus ON Lock Check FOK Check STOP Layer Check STOP sled move Auto Focus Offset Auto Tracking Offset Auto Tilt Offset Auto Focus Offset Auto Focus Gain Auto Tracking Gain...
6-6. Drive Manual Operation 6-6-3. Manual Control 1 Manual Control 1 In performing manual operation, observe the following points: Select correct disc type on the Disc Type screen. SA.000000 SI.00 EMG.00 First, select “0. Disc Type” and execute “7. Hydet init” and “8. Sled init”.
6-6-7. Manual Adjust 2 3. Auto Focus Gain : Adjust focus gain automatically. Adjusted result is reflected on the EEPROM (IC801). Execute this with CLVA turned on if pos- Manual Adjust 2 sible. If NG, the system will be defective, SA.000000 SI.00 EMG.00...
6-6-10. EEPROM Data Screen Display EEPROM data Focus Offset Focus Gain TRK Offset TRK. CONT. TRK Gain Tilt Offset Pullin Level EQ. Boost L.F.O SD. ?? HY. ?? Figure 20 This screen displays various set values including adjusted results stored in the EEPROM (IC801). ID No.
With the initial menu displayed, press [4] key on the remote com- N Emergency history (7) 00 00 00 00 00 00 mander (RMT-D107A), and the information on emergency his- 00 00 00 00 00 00 tory of Drvcon and Syscon will be displayed. This information is given over four pages, which can be changed over with [↑] and...
Page 90
How to see Emergency History Recovery NG Auto Sequence Time Out Auto Sequence Fail Syscon Stop request from drive controller was received At the mode change command, the mode could not be changed within specified time and the 1 EMG CODE drive stopped.
3 Disc Type (Mecha Mode: 6π) 6-9. Error Code The self-diagnosis function works to prevent the player from mal- functioning, a five-digit service number (combination of a letter and figures) flashes on the screen and front panel display. 1. Each user needs to manage the error......“C” code (A) Last result of disc type judgment.
Page 92
2. Each user needs to contact Code Description with the service section ..........“E” code At the mode change command, the mode could not be changed within specified time and the drive stopped. Retry due to supply error failed and the drive stopped.
DVP-S7700 SECTION 7 ELECTRICAL ADJUSTMENT 7-1. Power Supply Check In making adjustment, refer to 7-4. Adjustment Related Parts Arrangement. 1. HS-930SU Board Note: During diagnostic check, the characters and color bars can Mode be seen only with the NTSC monitor. Therefore, for diag- nostic check, use the monitor that supports both NTSC and Instrument Digital voltmeter...
7-2. Adjustment of System Control 2. S-terminal Output Check (MB-84 board) <Purpose> Check S-terminal video output. If it is incorrect, pictures will not 1. System Clock 27 MHz Adjustment (MB-84 board) be displayed correctly in spite of connection to the TV with a S- <Purpose>...
4. Checking Component Video Output R-Y 6. Checking S Video Output S-C (MB-84 board) 7-4. Adjustment Related Parts Arrangement (MB-84 board) <Purpose> <Purpose> This checks whether the S-C satisfies the NTSC Standard. If it is MB-84 BOARD (Side A) This checks component video output R-Y. If it is incorrect, cor- not correct, the colors will be too dark or light.
supplied 8-1-3. CHASSIS ASSEMBLY supplied supplied supplied supplied supplied supplied supplied T901 supplied supplied supplied The components identified by mark Les composants identifiés par une ! or dotted line with mark ! are criti- marque ! sont critiquens pour la cal for safety.
8-1-5. DVD MECHANISM CHASSIS ASSEMBLY (2) M501 M903 M901 The components identified by mark Les composants identifiés par une ! or dotted line with mark ! are criti- marque ! sont critiquens pour la cal for safety. sécurité. Replace only with part number speci- Ne les remplacer que par une pièce fied.
AU-218 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.