Advertisement
Quick Links
Register your product and get support at
EN Quick Start Guide
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CEM220_51_QSG_V1.0
CEM220
1
a
b
c
e
f
g
2
3
4
B
A
B
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4
B5 B6 B7 B8
A
a
b
c
d
Overview of parts 1
For cars with ISO connectors
These are the supplied parts needed to
Caution
connect and install this unit.
•
Be sure to connect the black ground (earth)
a In-car audio system
lead first.
b Sleeve
1
Connect the antenna and amplifier as
c Front panel
illustrated, if applicable.
d Trim plate
2
Cut off the bigger end of the supplied stan-
dard connector.
e Rubber cushion
3
Check the car's wiring carefully and connect
f Disassembly tools
them to the supplied standard connector.
g Screws (4 pieces)
4
Connect the supplied standard connector to
h ISO connector
the unit.
1
Green/black strip
Connection
2
White/black strip
Caution
3
Gray/black strip
•
Ensure that all loose leads are insulated with
electrical tape.
4
Purple/black strip
For cars with ISO connectors
2 3
1
Pull out the ISO connectors from car
e
RED
dashboard and connect them to the bigger
end of the supplied standard connector.
f
BLUE
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifier as
g
BLACK
illustrated, if applicable.
h
PINK
Connector
Connect to
i
YELLOW
1
REAR LINE OUT
Rear right
R
speaker
2
REAR LINE OUT
Rear left speaker
L
Attach the front panel 5
3
SUB OUT
Subwoofer
1
Attach the trim plate.
4
ANTENNA
Antenna
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
5
d
h
a
a
a
b
c
d
a
b
b
b
c
d
e
c
c
f
g
h
i
d
d
4
Release the panel to engage the left side.
3 4
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
•
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
•
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Left speaker
Remove the mounting sleeve with the
(Rear)
supplied disassembly tools.
Left speaker
4
Ensure that car dashboard opening is
(Front)
within these measurements:
Right speaker
5
(Front)
Install the sleeve into the dashboard and
bend the tabs outward to fix the sleeve.
Right speaker
6
(Rear)
Place the rubber cushion over the end of
the bolt.
7
Ignition key +12V DC
Slide the unit into the dashboard until you
when ON/ACC
hear a click sound.
Motor/electric antenna
8
Reconnect the negative terminal of the car
relay control lead/
battery.
Amplifier relay control
lead
Turn on
Ground
Illumination switch
1
Press z to turn on the unit.
To the +12V car battery
•
To turn off the unit, press z for 3
which is energized at all
seconds.
times
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press 3 or 4 repeatedly to until the cur-
rently time is displayed.
3
Turn
clockwise to set hour.
4
Press
to confirm.
5
Turn
anti-clockwise to set minute.
6
Press
to confirm.
•
To resume CD play, press
Insert the USB device
View clock
1
1
Press MENU/DISP repeatedly until the clock
Open the cover marked
is displayed.
panel.
2
Insert the USB device into the USB socket.
The unit star ts playing from the USB
Listen to radio
»
device automatically.
1
Press SOURCE repeatedly to select Radio.
2
Press
or
to select band: [FM1], [FM2],
Insert SD/MMC card
[FM3], [AM1], or [AM2] .
1
Press
to release the panel.
3
Press ∞ or § to tune to a radio station
2
Insert the SD or MMC card into the card
manually.
slot.
»
The radio station is broadcast.
The unit star ts playing from the SD/
»
To search for a radio station automati-
»
MMC card automatically.
cally, press
or
for 3 seconds.
Play with RDS
The RDS (Radio Data System) function operates
only in areas with FM stations broadcasting RDS
signals. If you tune to an RDS station, an RDS icon
and information about the presenter, station or
program is displayed.
Turn on RDS
Note
•
By default, the RDS function is off.
1
Press MENU/DISP for 3 seconds.
2
Turn
to select [RDS ON]:
»
[RDS]
is displayed.
•
To turn off the RDS function, repeat steps
above and choose [RDS OFF].
Play audio files
1
Press
on the front panel to release the
panel.
2
Insert a CD with the printed side facing up.
3
Close the panel.
4
Press 2; , to start play.
•
To pause CD play, press
2; .
2; again.
on the front
Advertisement
