Advertisement
Quick Links
SPECIFICATIONS
Power source
Input power (Max)
Vacuum
Power cord length
Radius of operation
Net weight
Dimensions (WxLxH)
Attachments: Dusting brush
Upholstery nozzle
Crevice nozzle
Extension wand
Specifications are subject to change without notice for further improvement.
MC-E540
AC230-240V
50Hz
1700W
18 kPa
6.5 m
6.5 m
7.2 kg
335x330x1095
•
•
•
•
Ref.: Z32J9000
Vacuum Cleaner
MODEL MC-E540
Matsushita Electric España, S.A.
DIVISION DE ASPIRADORAS
Zona Industrial del Polígono de CELRÀ
17460 CELRÀ (Girona) Spain
Advertisement
Related Manuals for Panasonic MC-E540
Summary of Contents for Panasonic MC-E540
- Page 1 Ref.: Z32J9000 Vacuum Cleaner MODEL MC-E540 SPECIFICATIONS MC-E540 Power source AC230-240V 50Hz Input power (Max) 1700W Vacuum 18 kPa Power cord length 6.5 m Radius of operation 6.5 m Net weight 7.2 kg Dimensions (WxLxH) 335x330x1095 • Attachments: Dusting brush •...
-
Page 2: Table Of Contents
..............SCHEMATIC DIAGRAM MC-E540 REAR COVER... -
Page 3: Pictorialwiring Diagram
PICTORIALWIRING DIAGRAM MC-E540 PARALLEL WIRE Yellow Yellow Blue MOTOR Brown Blue POWER SUPPLY ON/OFF Black SWITCH CAPACITOR THERMAL Brown CUT-OUT SWITCH COMPARTMENT REAR COVER MOTOR COMPARTMENT... -
Page 4: Exploded View
EXPLODED VIEW... - Page 5 EXPLODED VIEW...
- Page 6 SPARE PARTS LIST REF. No. DESCRIPTION PART No. Pcs/Set MC-E540 REMARKS FLOOR NOZZLE COVER ASS'Y AMC8A80J90A4 • PLASTIC SHAFT AMC8C27M1000 • FLOOR NOZZLE BUMPER AMC8A33M1034 • FLOOR NOZZLE PEDAL ASS'Y AMC8A78J9034 • TAPPING SCREW XTN4+18B • FRAME ASS'Y AMC8AZ7M1000 •...
- Page 7 AMC8Z07J9070 • German language CARTON BOX AMC8Z01J9000 • CUSHION A AMC8Z02M1000 • CUSHION B AMC8Z03M1000 • NOTE: Mechanical contruction of this model is similar to current one MC-E568. Differences between them are, MC-E540 without BEATER BAR SELECTOR and POWER CONTROL.
-
Page 8: Replacement Of Main Parts
REPLACEMENT OF MAIN PARTS IMPORTANT: Before replacing any part always DISCONNECT THE CLEANER FROM THE suction inlet ELECTRICITY SUPPLY. NOTE: Before any replacing operation, remove the hose to avoid damaging. (Fig. 1) Fig. 1 • BELT Screws 1. Remove the 5 screws from the base plate and lift it off. (Fig. 2) Base plate Belt Fig. - Page 9 REPLACEMENT OF MAIN PARTS 2. Release the belt from the motor shaft and lift the beater bar ass’y to remove the belt. (Fig. 3) 3. Replace the belt with a new one and place it around the motor shaft and beater bar pulley. Then reinstall the beater bar ass’y in its holding points.
- Page 10 REPLACEMENT OF MAIN PARTS 4. Replace the pedal ass’y with a new one and reinstall it in its place refastening the screw. (Fig. 6) 5. Reinstall the frame and refasten de two screws, then place the belt around the motor shaft. IMPORTANT: Before reinstall the base plate, make sure the Pedal belt is placed correctly between the screw and inside cover...
- Page 11 REPLACEMENT OF MAIN PARTS 6. Remove front and rear motor supports from the motor and Motor Rear replace it with a new one . (Fig. 10) motor support 7. Reassemble front and rear motor supports in the new motor and connect the lead wires according to the schematic diagram.
- Page 12 REPLACEMENT OF MAIN PARTS • POWER SUPPLY CORD 1. Loosen the 5 screws from the rear cover and take it out. Rear cover (Fig. 15) Power supply cord Fig. 15 2. Remove the cord cover and power supply cord connections. (Fig.
- Page 13 REPLACEMENT OF MAIN PARTS • ON/OFF SWITCH Switch cover 1. Loosen the 2 screws of the switch cover and remove it. (Fig. 17) Fig. 17 2. Remove the two lead wires (provided with quick-terminal) from the switch terminals and replace the ON/OFF switch with a new one.
-
Page 14: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY Power supply cord Check power supply cord continuity. If there is no continuity, replace it. Motor fails to rotate. Fuse (Plug for Check fuse continuity. If there is no continuity, replace it. (no noise is UK only) heard at all) - Page 15 PACKING INSTRUCTIONS...