• It works on the desk which performed measures against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. A1-1 23HLV84...
(Reading should not be above 0.5mA) Leakage Current Tester 1.5K ohm 0.15 µF PRODUCT UNDER TEST TEST PROBE Test all exposed KNOWN EARTH 2-Blade polarized metal surfaces GROUND type cord set Fig. 1 AC Leakage Test A1-2 23HLV84...
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit. A1-3 23HLV84...
Page 6
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. A1-4 23HLV84...
Page 7
EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING NEC-NATIONAL ELECTRICAL CODE ELECTRODE SYSTEM (NEC ART 250, PART H) S2898A A1-5 23HLV84...
[ When the installation of the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector. Pick Up PCB Make the short circuit using a soldering. Fig. 1 A1-6 23HLV84...
Press and hold the 'STOP' key on the front panel. Simultaneously press and hold the '9' key on the remote control unit. Hold both keys for more than 2 seconds. The On Screen Display message ' ' will appear. The Tray Lock has now been cleared. A1-7 23HLV84...
When soldering or unsoldering, completely remove all of the solder from the pins or solder area, and be sure to heat the soldering points with the lead free solder until it melts sufficiently. Recommendations Recommended lead free solder composition is Sn-3.0Ag-0.5Cu. A1-8 23HLV84...
INTERCONNECTION DIAGRAM .................... G-53, G-54 WAVEFORMS .......................... H-1~H-4 MECHANICAL EXPLODED VIEWS ..................I1-1~I1-3 DVD DECK EXPLODED VIEWS ..................... I2-1, I2-2 MECHANICAL REPLACEMENT PARTS LIST ..............J1-1~J1-4 DVD DECK REPLACEMENT PARTS LIST ................J2-1, J2-2 ELECTRICAL REPLACEMENT PARTS LIST ................ J3-1~J3-16 A2-1 23HLV84...
4Hz - 20kHz Power Power Source 120V, 60Hz Power Consumption at AC 110W at 120V 60Hz at DC Stand by (at AC) 1W at 120V 60Hz Per Year -- kWh/Year Protector Power Fuse Safety Circuit IC Protector(Micro Fuse) A3-1 23HLV84...
Page 13
Back Lighting Option On Timer Favorite CH CH Label VIDEO Label Locks V-Chip Lock New Password Panel Lock PC Monitor Menu Brightness Contrast Hor Position Ver Position Phase Clock Auto Adjust Reset Color Temperature Menu Green Blue Reset A3-2 23HLV84...
Page 14
Stereo, SAP, Mono CH / AV(Line) / DVD / PC Color Stream HD (Component) HDMI Channel (TV/Cable) CH Label Video Label Clock Game Timer Front Panel Lock On Timer Sleep Timer Reset Sound Mute V-chip Rating NOT AVAILABLE Picture Size A3-3 23HLV84...
Page 15
Track No G-11 OSD Language (TV) English, French, Spanish (DVD) English, French, Spanish G-12 Clock and Sleep Timer Max Time 120 Min Timer Step On Timer Program Wake Up Timer Timer Back-up (at Power Off Mode) more than A3-4 23HLV84...
Page 16
GENERAL SPECIFICATIONS G-13 Remote Unit RC-JX Control Glow in Dark Remocon Format TOSHIBA / NEC Custom Code 40-BF / 71-8E h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys 50 Keys Keys Power TV(DVD) CABLE...
Page 17
Tray Lock Video CD Playback SVCD Playback Overlay Graphics And Text Command List Entry Point Jump MP3 Playback JPEG Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out (Dolby Digital) (DTS) Screen Saver Audio DAC 192kHz / 24bit A3-6 23HLV84...
Page 18
610 x 276 x 484 610 x 115.5 x 438.5 w/o Handle, Stand Approx. W x D x H (mm) G-18 Weight Net (Approx.) 11.5kg (25.4 lbs) Net w/o Handle, Stand (Approx.) 10.5kg (23.2 lbs) Gross (Approx.) 14.5kg (32.0 lbs) A3-7 23HLV84...
Page 19
1 Corner / 3 Edges / 6 Surfaces Height (cm) Container Stuffing (40' container) Sets G-20 Material Cabinet Front PS 94V0 DECABROM Rear PS 94V0 DECABROM Jack Panel Non-Halogen Demand Eyelet Demand G-21 Environment Pb Free Lead-free Solder Other Cd Free A3-8 23HLV84...
Remove the Handle Angle in the direction of arrow. Remove the Stand Angle in the direction of arrow (B). Remove the 4 screws 3. Remove the Hinge Ass'y in the direction of arrow (C). Handle Angle Stand Stand Angle Hinge Ass'y Fig. 1-4 Fig. 1-2 B1-1 23HLV84...
Page 21
Remove the 5 screws 1. Remove the screw 1. Remove the Shield LCD and LCD PCB in the direction of Remove the Shield FFC. arrow. Remove the 3 screws 2. Remove the DVD PCB and Shield DVD in the direction of arrow. B1-2 23HLV84...
Page 22
PCB (Refer to Fig. 1-10) Fig. 1-11 Remove the 4 screws 1. Remove the Operation PCB and Operation 2 PCB in the direction of arrow (A). Remove the 2 screws 2. Remove the Remocon PCB in the direction of arrow (B). B1-3 23HLV84...
Remove the Mouth Ass'y. 29.7 ± 0.1mm Motor Mouth Ass'y Safety surface for pressing Fig. 2-1-B of the insert. Start SW PCB Ass'y End SW PCB Ass'y Black Motor Black • Screw Torque: 0.8 ± 0.2kgf•cm Fig. 2-3 Fig. 2-1-C B2-1 23HLV84...
Page 24
Unlock the 3 supports 1 and remove the Rack Loading. Remove the Rack Gear and Mid Rack Gear. • Screw Torque: 1.5 ± 0.2kgf•cm Fig. 2-7 Rack Loading Guide Arm Spring Rack Gear Mid Rack Gear Fig. 2-5 B2-2 23HLV84...
Page 25
Unlock the support 3 and remove the Disc R Lever. Clamper Ass'y Disc R Lever Disc Guide Arm Fig. 2-8-A NOTE 1. When installing the Clamper Ass'y, check if the Clamper Ass'y is locked correctly as Fig. 2-8-B. Fig. 2-8-B B2-3 23HLV84...
Shield Wire. (Refer to Fig. 3-4.) NOTE Do not move the Braided Shield Wire in the vertical Blower type IC direction towards the IC pattern. desoldering machine Braided Shield Wire Soldering Iron Fig. 3-2 IC pattern Fig. 3-4 B3-1 23HLV84...
Page 27
Fig. 3-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 3-7.) NOTE Do not absorb the solder to excess. Soldering Iron Braided Shield Wire Fig. 3-7 B3-2 23HLV84...
LCD ON 0010 POWER ON total hours. = (16 x 16 x 16 x thousands digit value) MICON Version OEC7114B_001 + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) FIG. 1 23HLV84...
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1 and 2. Main Micon side EEPROM (IC199) initial setting ADDRESS DATA INIT LCD ON 0010 OEC7114B_001 FIG. 1 CANADA Table 1 23HLV84...
Page 30
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. 23HLV84...
INPUT button on the remote control. And, to display the adjustment screen for DVD mode, press the TV/DVD button on the remote control. Press the VOL.DOWN button on the set and the channel (9) on the remote control for more than 2 second. 23HLV84...
Page 32
FUNCTION STEP NO. DRI1 M BRIGHT MAX DRI2 M BRIGHT CENTER MD6 M BRIGHT MIN DTHON M CONT MAX DRREF M CONT CENTER RCUT2 M CONT MIN GCUT2 M RED CENTER BCUT2 M GREEN CENTER GAINR M BLUE CENTER 23HLV84...
Page 36
I2C_DL MICON/ SOUND AMP IC SUB MICON IC302 LA4901-E 11 IN ON TIME OUT+ AUDIO_MUTE MUTE OUT- VCC(SW) SOUND+B HEADPHONE AMP IC IC304 NJM2151AV 3 MUTE LINE IN R HEADPHONE JACK J301 LINE IN L HP.OUT R HP.OUT L 23HLV84...
Page 37
PIXEL_RDY RESET TV POWER POWER_ON_H CNVSS. LCD_H LCD_H TU001 STEREO/SOUND AMP SUB MICON IC102 OEC6081A VDD 42 X IN X104 SCL 11 16MHz X OUT SCL1 SCL1 SCALER1/SCALER2/LVDS/ ADC/MEMORY/BUS SDA1 SDA1 EEP ROM IC 16K IC104 S-24C16AFJA-TB-01 SCALER1/SCALER2/ LVDS/ADC/MEMORY/ 23HLV84...
Page 47
N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED PCBD20 DANS LA NOMENCLATURE DES PIECES WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CMD004 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 23HLV84...
:LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE PCBD20 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME N’UTILISER QUE CELLS DECRITES CMD004 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DANS LA NOMENCLATURE DES PIECES 23HLV84...
:LES PIECES REPAREES PAR UN ETANT NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DANGEREUSES AN POINT DE VUE SECURITE PCBD20 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE N’UTILISER QUE CELLS DECRITES CMD004 DANS LA NOMENCLATURE DES PIECES 23HLV84...
TV/DVD TV/DVD VAR_A_OUT_L VAR_A_OUT_R CAUTION: DIGITAL TRANSISTOR NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. PCBD20 CMD004 23HLV84...
:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DANS LA NOMENCLATURE DES PIECES N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. (F3801). 23HLV84 G-10...
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES G-11 23HLV84 G-12...
Page 53
NOTE:THE DC VOLTAGE EACH PART WAS PCB340 PIXEL_RDY NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME PIXEL_RDY MEASURED WITH THE DIGITAL TESTER CED016 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PIXEL_DATA PIXEL_DATA DURING PLAYBACK. PIXEL_CLK PIXEL_CLK G-13 23HLV84 G-14...
AB19 AF18 OSDYSB_IN OSD_H OSD_V NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME PCB340 MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CED016 DURING PLAYBACK. G-15 23HLV84 G-16...
VSS12 VSS12 AF26 DTMB DRAM1GND1 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PCB340 DURING PLAYBACK. CED016 G-17 23HLV84 G-18...
47uH L805 NLCV32T 47uH NLCV32T NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME PCB340 MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CED016 DURING PLAYBACK. G-19 23HLV84 G-20...
Page 57
VD_OUT HD_OUT FROM/TO REG/HD/VD P.CON+3.3V NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. PCB340 CED016 G-21 23HLV84 G-22...
Page 58
CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PCB340 MEASURED WITH THE DIGITAL TESTER CED016 DURING PLAYBACK. G-23 23HLV84 G-24...
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. PCB340 CED016 G-25 23HLV84 G-26...
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES DURING PLAYBACK. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES PCB340 CED016 G-27 23HLV84 G-28...
Page 61
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. PCB340 CED016 G-29 23HLV84 G-30...
Page 62
FROM/TO REG/HD/VD L801 P.CON+5V 47uH NLCV32T PCB340 NOTE:THE DC VOLTAGE EACH PART WAS CED016 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. G-31 23HLV84 G-32...
Page 63
RAMCLK R4054 R4053 BOOTSEL2 BOOTSEL1 PCB130 DMD005 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. G-33 23HLV84 G-34...
Page 64
FCM2012H-102T04 D_GND FROM/TO AUDIO/VIDEO RESET NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS PCB130 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DMD005 DURING PLAYBACK. G-35 23HLV84 G-36...
Page 65
R2654 TP41 CAUTION: DIGITAL TRANSISTOR NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS PCB130 DMD005 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. G-37 23HLV84 G-38...
Page 66
DVD_AUDIO_R DVD_A_OUT_R SYS_MUTE MCL4148 D8510 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. PCB130 DMD005 G-39 23HLV84 G-40...
Page 67
R2334 LDO+ DISC_END_SW NOTE:THE DC VOLTAGE EACH PART WAS LDO- NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER PCB130 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DISC_IN_SW DMD005 DURING PLAYBACK. G-41 23HLV84 G-42...
Page 68
5A 32V (F3001) ATTENTION :LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE CAUTION :F3001 IS MANUFACTURED BY COOPER INDUSTRIES INC., N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES TYPE 1206FA-T. PCB130 DMD005 G-43 23HLV84 G-44...
Page 69
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. G-45 23HLV84 G-46...
Page 70
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. PCBDJ0 CED011 G-47 23HLV84 G-48...
Page 71
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST PCBDJ0 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. CED011 G-49 23HLV84 G-50...
Page 72
START SW/END SW SCHEMATIC DIAGRAM DECK CD CV-VTM101A M2301 MDN3BT3ESA 2H091902 04_6232_104_015_800 STEPPING_MOTOR[B-] STEPPING MOTOR(B-) STEPPING_MOTOR[B+] STEPPING_MOTOR(B+) STEPPING_MOTOR[A-] STEPPING_MOTOR(A-) STEPPING_MOTOR[A+] STEPPING_MOTOR(A+) S2001Y LOADING_MOTOR[+] S2004Y DISC_END_SW S2002Y LOADING_MOTOR[-] S2003Y DISC_IN_SW ESE22MH22 PCB580 BED005 PCB590 BED006 (START SW PCB) ESE22MH24 (END SW PCB) NOTE:THE DC VOLTAGE EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER...
Page 73
:SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES G-51 23HLV84 G-52...
500mV MEMORY 2 200µs 10µs 2µs 500mV 200mV 2.0V TUNER/MICON RF_AMP 10µs 200ns 200mV 100mV 1.0V 200ns 10µs 200mV 100mV 1.0V The following waveforms were measured at the point of the corresponding NOTE: balloon number in the schematic diagram. 23HLV84...
Page 75
SUB MICON 10µs 0.5ms 0.5ms 0.5V 1.0V 1.0V 20µs 50µs 50µs 1.0V 1.0V 1.0V SOUND AMP 50ns 20µs 1.0V 50mV 1.0V The following waveforms were measured at the point of the corresponding NOTE: balloon number in the schematic diagram. 23HLV84...
Page 76
0.5V 500µs 50µs 200mV 200mV 0.5V DECODER 500µs 10µs 50µs 200mV 0.5V 0.5V MICON2 INTERFACE 500µs 10µs 10µs 1.0V 200mV 0.5V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. 23HLV84...
DVD DECK EXPLODED VIEW (TOP VIEW) NOTE: Applying positions AA for the grease are CLASS MARK displayed for this section. GREASE Check if the correct grease is applied for each position. I2-1 23HLV84...
Page 82
DVD DECK EXPLODED VIEW (BOTTOM VIEW) PCB580 (START SW PCB ASS'Y) PCB590 M2301 (END SW PCB ASS'Y) NOTE: Applying positions AA for the grease are CLASS MARK displayed for this section. GREASE Check if the correct grease is applied for each position. I2-2 23HLV84...