LG LGES-5048 Quick Installation Instructions page 4
Hide thumbs
Also See for LGES-5048:
- User manual (18 pages) ,
- Quick installation manual (18 pages) ,
- User manual (37 pages)
Advertisement
Step 1. Instructions For Quick Installation
Step 2. SOP of Battery Connection
Step 3.Wi-Fi Conguration Instruction
Note:WiFi Configuration could also be done on LGES PV Master App， for details, please download "LGES PV Master Operation Introduction" at
https://www.lgessbattery.com/au/home-battery/product-info.lg
Preparation
1. Power Wi-Fi inverter (or Power on Inverter) on.
2. Power router on.
Preparation
1.Click 'Start Setup'
Please select you current wireless network
Firmware version
1.6.9.3.38-2.1.38
MAC address
60:C5:A8:60:33:E1
Wireless AP mode
Enable
SSID
Solar-WiFi
IP address
10.10.100.253
Wireless STA mode
Disable
Router SSID
WiFi_Burn-in
Encryption method
WPA/WPA2-PSK
Encryption algorithm
AES
WiFi_Burn-in
Router Password
The Wi-Fi module
Please select you current wireless network
parameters please
refer to 'Device
router doesn't exist, or signal is too weak, or password is incorrect.
information'
Help: Wizard will help you to complete setting within one minute.
column above.
Start Setup
Please select you current wireless network
SSID
Sec mode
Enc type
Channel
RSSl
WiFi-Test WPA2-PSK
AES
06
54%
Note: When RSsl of the selected Wi-Fi network is lower
than15%, the connection may be unstable, please select
other available network or shorten the distance between
lf the router is not in
the device and router.lf you wireless router does not
the site list, please
broadcast SSID, please click ' Next'and add a wireless
refer to No.4 in
network manually.
'Troubleshooting'.
Back
Next
Troubleshooting
No.
Problem
Checking Items
1.Make sure inverter is powered on;
Cannot Find
2.Move your smart device closer to inverter;
1
Solar-WiFi Signal
3.Restart inverter;
4.Do "WiFi Reload' operation refer to user manual.
1.Try password: 12345678;
2.Restart inverter;
Cannot connect to
2
3.Make sure there is no other device connected to
Solar-WiFignal
Solar-WiFi;
4.Do 'WiFi Reload' operation and try again.
1.Make sure user name and password you use are both
admin;
2.Do 'WiFi Reload' operation and try again;
3
Cannot login
3.Try another browser (suggest use Google, FireFox, IE，
website
Safari etc.);
10.10.100.253
4.Make sure website you log in is 10.10.100.253
1.Move router closer to inverter or use a Wi-Fi repeater
device;
Cannot find router
4
2.Connect to router and login the setting page to check
SSID
the channel it uses. Please make sure the channel is
not bigger than 13. Otherwise, modify it.
Step 3. WiFi Configuration Instruction
Connect to 'Solar-WiFi'
1.Wi-Fi name: Solar-WiFi*(* means the last 8 characters of
inverter serial NO.)Password: 12345678
2.Browse website: 10.10.100.253
10.10.100.253
B-3: Enter User name:admin, Password:admin, click OK
Admin(U) :
admin
Password :
Remember the password(R)
CANCEL
Connect to 'Solar-WiFi'
1.Fill in router password and click 'Next'
Add wireless network manually:
Network name (SSID)
WiFi-Test
Encryption method
WAP/WPA2-PSK
Encryption algorithm
AES
Please enter the wireless network password:
Password (8-63 bytes)
Router password
Please make sure
Remember the password(R)
all parameters of
wireless network
★Note: case sensitive for SSID and Password.
Please make sure all parameters of wireless network
are matched with
are matched with router, including password.
the router's,
including password.
Back
Next
Save success!
Note:
The 'Solar-WiFi'signal
Click 'Complete', the current configuration will take effect
will disappear after
after restart.
inverter connects to
lf you still need to configure the other pages of information,
WiFi router.Turn off
please go to complete your required configuration.
router or do WiFi
Configuration is completed, you can log on the
reload operation via
Management page to restart device by click on 'OK' button.
button on inverter if
Confirm or complete?
you need connect to
'Solar-WiFi' once again.
Back
Complete
No.
Problem
Checking Items
1.Restart inverter
2.Connect to Solar-WiFi and login again， check the
'SSID", 'Security Mode'， 'Encryption Type'and 'Pass
Phrase' is matching with that of router or not;
Cannot Find
3.Connect to router and login to check if the
5
Solar-WiFi Signal
connection reaches the maximum amount or not,
and to check the channel of it uses. Please make sure
the channel is not bigger than 13.Otherwise, modify it;
4.Restart router ;
5.Move router closer to inverter or use a WiFi repeater
device.
1.Connect to the router and visit the portal
After configuration,
www.lgresuhomemonitor.com Check the portal is
WiFi Led on inverter
6
available or not;
blink four times
2.Restart router and inverter;
repeatedly
3.Make sure the inverter is registered on the platform.
Advertisement
