Page 1 Conditions of Use: (1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information for any purpose other than the purpose described foregoing is forbidden. (2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
Page 2 警告このマニュアルは，サービス専用です。お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，人身事故につながることがあります。危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。 WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Page 3 注意 FÖRSIKTIGHET! 指定以外の電池に交換すると，破裂する危険があり Fara för explosion vid felaktigt placerat batteri. ます。 Byt endast mot samma eller likvärdig typ av batteri, 必ず指定の電池に交換してください。 enligt tillverkarens rekommendationer. 使用済みの電池は，国または地域の法令に従って När du kasserar batteriet ska du följa rådande lagar 処理してください。 för regionen eller landet. CAUTION PAS PÅ...
Page 4: Table Of Contents
Table of Contents Section 1 Service Overview ....................5 1-1. Product Comparison Table ......................5 1-2. Location of Boards ........................6 1-3. Circuit Description ........................8 1-3-1. OHB Block ..........................8 1-3-2. Main Block ..........................8 1-3-3. Rear Block ........................... 11 1-3-4.
Page 5 Section 2 Replacement of Parts ................... 40 2-1. Basic Knowledge........................40 2-1-1. Tightening Torque ........................ 40 2-1-2. Arrows on Plates and Boards ....................40 2-2. Top Cabinet, Bottom Cover ......................41 2-3. Inside Panel ..........................43 2-3-1. Lithium Battery ........................46 2-3-2.
Page 6 2-17-2. Panel Module, PSW-1001 Board ..................126 2-18. Grip ............................128 2-18-1. Exterior Parts ........................128 2-18-2. UIF-1001 Board, UC-1001 Board ................... 133 Section 3 Error Code ......................135 3-1. Error Code List ......................... 135 Section 4 Service Menu ..................... 138 4-1.
Page 7 Overall ............................168 Frame Wiring ..........................173 Revision History ........................174...
Page 8: Section 1 Service Overview
Section 1 Service Overview 1-1. Product Comparison Table Model ILME-FX6V ILME-FX6VK ILME-FX6T ILME-FX6TK Destination UC, J, CN1, CEE, UC, J, CN1 UC, CEE, AF1 UC, CEE IN5, E38, AP2 COLOR system NTSC/PAL (Selectable) NTSC/PAL (Selectable) Internal recording media — —...
Page 9: Location Of Boards
1-2. Location of Boards WF-1008 SS-1007 SW-1037 KY-1031 SEL-1001 VSW-1001 PS-1004 FU-1001 HP-1015 SH-1030 TG-1005 WB-1002 DD-1020 IF-1014 CK-1027 VC-1046 HD-1006 VF-1024 SDI-1004 TC-1002 FT-2001 LC-1052 DC-1023 CR-1006 JK-1029 WF-12 Note The IS-1043 board cannot be replaced in units of mount board or mounted components. When replacement of this board is needed, replace the front block.
Page 10 DL-1007 HN-1054 HK-1003 HS-1008 FP-310 HC-1002 AXM-1002 PD-1066 PSW-1001 FP-311 UC, CEE, CN1, IN5, E38, AF1, AP2 UC-1001 UIF-1001 CHG-1003...
Page 11: Circuit Description
1-3. Circuit Description 1-3-1. OHB Block CR-1006 board The CR-1006 board contains a driver IC6502 to control the variable ND filter. Control signals of the variable ND filter are connected from IC1000 on the VC-1046 board. Signals from IC6502 are connected to the ND unit to insert or remove the variable liquid crystal ND of the ND unit and to change the density of the variable liquid crystal ND.
Page 12 FT-2001 board The FT-2001 board contains an LED for FRONT TALLY. IF-1014 board The IF-1014 board is a unit-side connector board for relay between the unit and the handle. This board relays the switch signals of the handle and power and communication lines of the internal microphone in the handle, audio input connectors (INPUT1 and INPUT2), and MI SHOE.
Page 13 Analog signals from the audio input connectors are converted to digital signals, and the converted digital signals are input to IC8000 and are then output to IC9100. Furthermore, IC8000 receives switch input signals from the audio input connector and changes the control of the audio signal A/D conversion block.
Page 14: Rear Block
1-3-3. Rear Block HD-1006 board The HD-1006 board contains an HDMI connector. IC1503 works as an HDMI Retimer IC. SDI-1004 board The SDI-1004 board contains a BNC connector that can output 12G-SDI signals. IC6004 is a 12G-SDI driver IC. TC-1002 board The TC-1002 board contains a TC IN/TC OUT (timecode input/output) connector.
Page 15 SS-1007 board The SS-1007 board contains a HOLD switch, a recording START/STOP button, a REC LED, and a Clip Flag button. SW-1037 board The SW-1037 board contains ASSIGN 1, ASSIGN 2, and ASSIGN 3 buttons and a DISPLAY button. TG-1005 board The TG-1005 board contains an ISO/GAIN switch (for switching gain) and a WHT BAL switch (for switching white balance memory).
Page 16: Outside Block
1-3-5. Outside Block DC-1023 board The DC-1023 board contains a DC IN jack. JK-1029 board The JK-1029 board contains a 3.5ϕ jack connector only for grip connection. Connection to the grip starts power supply from the VC-1046 board and UART signal communication. LC-1052 board The LC-1052 board contains a USB/multi connector, a REMOTE connector, a TC IN/OUT switch, and an NFC Plug IC.
Page 17: Viewfinder Block
HC-1002 board The HC-1002 board is a handle-side connector board for relay between the unit and the handle. This board relays the switch signals of the handle and power and communication lines of the internal microphone in the handle, audio input connectors (INPUT1 and INPUT2), and MI SHOE. HK-1003 board The HK-1003 board contains a handle recording START/STOP button, ASSIGN7, ASSIGN8, and a handle HOLD switch.
Page 18: Grip Block
1-3-8. Grip Block FP-311 board The FP-311 board contains ASSIGN4, ASSIGN5, recording START/STOP button, eight direction keys, and a photo reflector to activate the multi-assignable dial. UC-1001 board The UC-1001 board contains an ASSIGN6 button. UIF-1001 board The UIF-1001 board is a grip board to control the grip using IC2002. When this board is connected to the camera body, the LED (D2002) lights green.
Page 19: Connectors And Cables
1-4. Connectors and Cables When connecting cables to connectors during installation or service, use connectors and cables that meet the specifications of this unit. 1-5. Connector Input/Output Signals 1-5-1. Location of Connectors...
Page 20: Input Signals
1-5-2. Input Signals 1. DC-IN DC jack EIAJ standard, DC 18 V to 20.5 V EXT DC - External View - 2. AUDIO INPUT 1/2 XLR 3-pin, Female - External View - (0 dBu = 0.775 V rms) Signal Specifications —...
Page 21: Input/Output Signals
5. USB/Multi Multi/micro USB -External View- Signal Specifications USB_VBUS +5 V power (input) USB D- IN/OUT USB Data- signal USB D+ IN/OUT USB Data+ signal USB_ID OTG identification signal (not used) — D_3.3V +3.3 V (not used) XRESET_REQ Camera power On/Off control (for debugging) UART_TX IN/OUT UART TX (for debugging)
Page 22 7. HDMI OUT Type A - External View - Signal Specifications TMDS DATA2+ TMDS data 2 (+) output TMDS DATA2 SHIELD GND for TMDS data 2 — TMDS DATA2- TMDS data 2 (-) output TMDS DATA1+ TMDS data 1 (+) output TMDS DATA1 SHIELD GND for TMDS data 1 —...
Page 23 (USB connector) Type C - External View - Signal Specifications — TX1+ Super Speed differential pair TX1- Super Speed differential pair VBUS IN/OUT 5 V power Plug Configuration Detection IN/OUT USB2.0 Interface IN/OUT USB2.0 Interface SBU1 No Connection — VBUS IN/OUT 5 V power RX1+...
Page 24 11. LCD -External View- Note The viewfinder connection cable supplied with the unit is not connected in a 1-1 or 1-N manner. Signal Specifications — — GND(VF_DET2) Cable connection detection signal 2 (GND) — CAP_TP_INT Touch panel interrupt signal +5 V power LVDS DATA 2+ LVDS data 2 (+) output LVDS DATA2-...
Page 25 Signal Specifications — TP_SDA IN/OUT TP data signal — TP_SCL TP clock signal — I2C_SCK EEPROM clock signal LCD CS signal XRST LCD reset signal VF_DET Cable connection detection signal 1 BL_CONT Backlight PWM signal 12. Handle connector -External View- Signal Specifications D_5.0V_DD...
Page 26 Signal Specifications JOY_STICK_C Multi selector signal D_7.0V_DD +7V Power (MIRA)_XDIAL_3_A Assignable dial signal 2ND_ZOOM_AD Zoom Key AD signal (SW)2(MONI)_AU_SEL0_CH2 XLR key switch signal (SW)2(MONI)_AU_SEL1_CH2 XLR key switch signal (XLR)2(MONI)_I2S_DATA XLR Data signal (MUX)2(DFF)_48V_SEL_CH1AND2 Enable signal of the XLR+48V power (MUX)2(DFF)_MIC_REF_SEL0_CH1AND2 Enable signal of the XLR MIC input (MUX)2(DFF)_INT_RST_X_AND_DIG_ MIC/DIG SHOE reset signal...
Page 27: Functions Of Onboard Led Indicators
1-6. Functions of Onboard LED Indicators 1-6-1. VC-1046 Board D8001 VC-1046 Board/Side A Ref No. Name Color Description Normal State (Power On) D8001 Yellow green Indicates completion of FPGA configuration and completion power supply to the VC-1046 board. 1-6-2. UIF-1001 Board D2002 UIF-1001 Board/Side A Ref No.
Page 28: Notes On Replacing Parts And Board
1-7. Notes on Replacing Parts and Board 1-7-1. Power Supply during Repairs AC power adaptor Use the AC power adaptor when repairing the unit. 1-7-2. Notes for Replacing the VC-1046 Board Adjustment values of the camera are written to the VC-1046 board in this unit. For this reason, when the VC-1046 board is replaced, activate the Adjust Manual from the Adjust Station.
Page 29: Notes For Replacing The Ck-1027 Board
Work: 1. Execute [Read and Save] of “RESTORE DATA” in the DATA tab. 2. After replacement with the repair VC-1046 board, execute [LOAD and WRITE] of “PRODUCT ID & USB SERIAL No. INPUT” in the ADJUST tab of the Adjust Manual to write extracted data to the unit.
Page 30: Notes For Replacing The Cr-1006 Board
1-7-4. Notes for Replacing the CR-1006 Board A six-axis sensor is installed on the CR-1006 board in the unit. When the CR-1006 board is replaced, activate the Adjust Manual from the Adjust Station, and then execute “Gyro Check” and “Level adj” according to the Adjust Manual. 1-7-5.
Page 31: Tools And Fixtures
1-8. Tools and Fixtures Part No. Name Usage/Note J-6323-420-A Torque screwdriver bit Tightening screws, for M2 machine screw, for M2.6 machine screw J-6325-110-A Torque screwdriver bit (M1.4) Tightening screws, for precision M1.4, for precision M1.7 J-6325-380-A Torque screwdriver bit (M2) Tightening screws, for precision M2, for precision M2.6 J-6325-400-A...
Page 32: Circuit Protection Parts
1-9. Circuit Protection Parts 1-9-1. Circuit Protection Element This unit is equipped with positive-characteristic thermistors (power thermistors) as circuit protection elements. The positive-characteristic thermistor limits the electric current flowing through the circuit as the internal resistance increases when an excessive current flows or when the ambient temperature increases. If the positive-characteristic thermistor works, turn off the main power of the unit and inspect the internal circuit of the unit.
Page 33: Electrical Adjustment
1-10. Electrical Adjustment For adjusting this unit, the Adjust Station and the Adjust Manual are required. • Adjust Station It is the software to start up Adjust Manual for each model. For details, refer to Installation manual supplied with the installer for the Adjust Station. •...
Page 34: Cables To Handle With Care
1-11. Cables to Handle with Care 1-11-1. Disconnecting/Connecting Flexible Flat Cable and Flexible Board Note • Be very careful not to fold flexible flat cables and flexible board. Life of flexible flat cable and flexible board will be significantly shorted if they are folded. •...
Page 35: Disconnecting/Connecting Fine-Wire Coaxial Cable
1-11-2. Disconnecting/Connecting Fine-Wire Coaxial Cable Note • Be very careful when handling the fine-wire coaxial cable so that fine wires are not broken. • When disconnecting the fine-wire coaxial cable, be sure to hold the connector. Do not attempt to pull the cable.
Page 36 Type B Disconnection 1. Hold both sides of the fine-wire coaxial cable connector, and pull the connector straight to disconnect Both sides of connector Hold the connector to disconnect. Correct Do not attempt to disconnect by Fine-wire coaxial cable Wrong pulling the cable.
Page 37 Type C Disconnection 1. Use a tool with a hook as shown below. Hook the tool's hook to the connector of the fine-wire coaxial cable. 2. Lift the tool straight in the arrow direction with the hook hooked to disconnect the connector of the fine-wire coaxial cable.
Page 38 Type D Disconnection 1. Raise the pull-bar in the direction of arrow A to unlock the connector. 2. Hold both sides of the fine-wire coaxial cable connector, and pull the connector straight to disconnect Pull-bar Correct Hold the connector to disconnect. Fine-wire coaxial cable Connector...
Page 39: Disconnecting/Connecting Coaxial Cable
1-11-3. Disconnecting/Connecting Coaxial Cable Type A Disconnecting 1. Hold the plug of coaxial cable. 2. Pull out the coaxial cable in the arrow direction. Note Be sure to hold the plug when disconnecting the coaxial cable. Do not pull the cable. Correct Wrong Hold the plug to remove.
Page 40: Cleaning The Optical Filter Block And The Nd Unit
1-12. Cleaning the Optical Filter Block and the ND Unit The following parts of this unit can be cleaned. • Both the front and back surfaces of the optical filter block. • The surface of the ND unit facing toward the optical filter. Front surface of the optical filter block The surface of the ND unit Back surface of the optical filter block...
Page 41 Procedure 1. Remove the optical filter block. (Refer to “2-7-2. Optical Filter Block”.) As a protective film is attached to a new optical filter, remove the film before starting the replacement procedure of the optical filter block. 2. Clean the surface with dew condensation or dust. How to use cleaning tools •...
Page 42 • Cleaning stick (Part number: J-6082-712-A) Visually check the contaminated area, and then slide the tip of the cleaning stick to remove dust and dirt. Cleaning stick Optical filter block...
Page 43: Section 2 Replacement Of Parts
Section 2 Replacement of Parts 2-1. Basic Knowledge 2-1-1. Tightening Torque When tightening screws used in this unit, be sure to use a torque driver and tighten screws to the specified tightening torque. If the specified tightening torque is described in the text in this section, tighten screws to the specified tightening torque in the text.
Page 44: Top Cabinet, Bottom Cover
2-2. Top Cabinet, Bottom Cover Procedure 1. Release the hooks, and then remove the handle connector protective cap. 2. Remove the six screws, and then remove the top cabinet. 3. Remove the megeyar hook. Handle connector protective cap P2.6 x 5 Hooks Megeyar hook Top cabinet...
Page 45 4. Remove the seven screws, and then remove the bottom cover. Bottom cover P2 x 4 Screw tightening sequence and pushing directions Inside panel Outside panel Note • When installing the bottom cover, push the outside panel and inside panel in the direction of the arrow, then tighten the screws in the following sequence: (a), (b), (c), (d), (e), (f).
Page 46: Inside Panel
2-3. Inside Panel Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) Procedure 1. Disconnect the coaxial cable from the connector (J0200) on the CK-1027 board. Boss CK-1027 board Coaxial cable J0200 Note At the time of installation, pass the coaxial cable around the front side of the boss and arrange it so that it does not protrude higher than the boss.
Page 47 2. Open the media lid, and then remove the two screws. Pushing directions Inside panel P2 x 4 P2 x 4 Media lid Note At the time of installation, push the inside panel in the direction of the arrow and tighten the screws. 3.
Page 48 4. Draw the inside panel. Note The inside panel and main unit are connected with the flexible board. When drawing the inside panel, be careful not to damage flexible board. 5. Disconnect the flexible board from the connector (CN9603) on the VC-1046 board. Silicon tube Placement of flexible board Flexile board...
Page 49: Lithium Battery
2-3-1. Lithium Battery Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) Procedure 1. Remove the lithium battery with a non-conductive stick. Lithium battery Hooks Groove...
Page 50: Hp-1015 Board
2-3-2. HP-1015 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) Procedure 1. Disconnect the flexible flat cable from the connector (CN0301) on the KY-1031 board. 2.
Page 51: Ky-1031 Board, Ps-1004 Board
2-3-3. KY-1031 Board, PS-1004 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) Procedure 1. Release the flexible flat cable (a) from the hook, and then disconnect it from the connector (CN002) on the PS-1004 board and the connector (CN0104) on the KY-1031 board.
Page 52 3. Raise the shade media sheet, and then remove the eight screws. Shade media sheet Holes TP2 x 5 Bosses Screw tightening sequence Inserting position of shade media sheet Note • At the time of installation, tighten screws (a) to (h) sequentially in alphabetical order. •...
Page 53 4. Pull up the two media tallies out of the grooves, and then remove them from the holes. Media tallies Hole Holes Groove Grooves 5. Open the USB cover. 6. Remove the media lid retainer. Holes Media lid retainer Bosses USB cover...
Page 54 7. Disconnect the flexible board from the connector (CN0105) on the KY-1031 board. 8. Remove the control switch block (AU95700). Holes Control switch block (AU95700) Flexible board KY-1031 board Bosses CN0105 9. Remove the five screws, and then remove the KY board plate. 10.
Page 55 12. Remove the screw, and then remove the KY-1031 board. 13. Disconnect the flexible board from the connector (CN0100) on the KY-1031 board. Flexible board Valley fold CN0100 KY-1031 board TP2 x 5 KY printed Valley fold CN0200 Switches KY-1031 board (CN0100) Audio slide levers Note...
Page 56 14. Disconnect the flexible flat cable from the connector (CN0100) on the SEL-1001 board. 15. Remove the PS-1004 board. 16. Disconnect the flexible flat cable from the connector (CN003) on the PS-1004 board. Hole Switch Reinforcing plate side: PS-1004 board CN003 Flexible flat cable Hole...
Page 57: Sel-1001 Board
2-3-4. SEL-1001 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the KY-1031 board. (Refer to “2-3-3. KY-1031 Board, PS-1004 Board”.) Procedure 1.
Page 58: Fu-1001 Board
2-3-5. FU-1001 Board Note The following parts are not reusable. Prepare new parts in advance. • Tape AS: 1 pc Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) Procedure 1.
Page 59 4. Peel off the tape AS. Note The tape AS is not reusable. 5. Remove the supplied nut of the FU-1001 board, and then remove the FD plate. Tape AS sticking standard Tape AS Tape AS Pins of the connector Sticking standard Sticking standard FU-1001 board...
Page 60: Tg-1005 Board, Sh-1030 Board
2-3-6. TG-1005 Board, SH-1030 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the HP-1015 board. (Refer to “2-3-2. HP-1015 Board”.) Procedure 1.
Page 61 3. Remove the two toggle packings. 4. Remove the screw, and then remove the TG-1005 board. 5. Disconnect the flexible flat cable from the connector (CN001) on the TG-1005 board. ISO button plate Bosses Reinforcing plate side: TG-1005 board Holes CN001 Flexible flat cable Pins of the connector...
Page 62 6. Disconnect the flexible flat cable from the connector (CN0001) on the SH-1030 board. 7. Remove the SH-1030 board. CN0001 SH-1030 board Holes Bosses Flexible flat cable 8. Install the removed parts by reversing the steps of removal.
Page 63: Wb-1002 Board
2-3-7. WB-1002 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the HP-1015 board. (Refer to “2-3-2. HP-1015 Board”.) 4.
Page 64 2. Remove the screw, and then remove the WB-1002 board. Hole PUSH AUTO button plate Boss Convex portion Hole WB-1002 board P1.7 x 3 At the time of installation, observe the following instructions. 1. Insert the convex portion of the WB-1002 board into the hole of the PUSH AUTO button plate. 2.
Page 65: Vsw-1001 Board, Sw-1037 Board
2-3-8. VSW-1001 Board, SW-1037 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the lithium battery. (Refer to “2-3-1. Lithium Battery”.) 4.
Page 66 3. Disconnect the five flexible flat cables from the following connectors. KY-1031 board: CN0101, CN0102 SS-1007 board: CN0100 SW-1037 board: CN0100 VSW-1001 board: CN0100, CN0102, CN0104, CN0105 Flexible flat cables Reinforcing plate side: KY-1031 board CN0101 CN0100 (SW-1037 board) CN0102 CN0100 (SS-1007 board) Flexible flat cable...
Page 67 4. Remove the six screws, and then remove the ND button plate and the ND insulation sheet. TP2 x 5 Hole ND button plate Holes Hole ND insulation sheet Bosses Bosses Note At the time of installation, tighten the screws in the following sequence: (a), (b), (c), (d), (e), (f).
Page 68 5. Remove the VSW-1001 board. Hole Switch VSW-1001 board Switch Hole Groove of the focus switch Boss Groove of the ND switch Boss Note When installing the VSW-1001 board, align the two switches with the two grooves.
Page 69 6. Remove the SW-1037 board. Hole SW-1037 board Hole Bosses 7. Install the removed parts by reversing the steps of removal.
Page 70: Ss-1007 Board, Wf-1008 Board
2-3-9. SS-1007 Board, WF-1008 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the lithium battery. (Refer to “2-3-1. Lithium Battery”.) 4.
Page 71 2. Remove the REC button and the hold switch. Hold switch Hold switch REC button REC button Note • At the time of installation, attach the REC button with the orientation shown in the figure. • At the time of installation, push the hold switch in the direction of the arrow. 3.
Page 72 5. Remove the screw, and then remove the REC button base assembly and the SS-1007 board. REC button base assembly Boss P1.7 x 3 SS-1007 board REC plate Hole Boss Hole Hole Hole 6. Install the removed parts by reversing the steps of removal.
Page 73: Outside Panel
2-4. Outside Panel Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) Procedure 1. Disconnect the flexible flat cable from the connector (CN1000) on the FT-2001 board. 2. Disconnect the coaxial cable from the connector (J0201) on the CK-1027 board. Groove CN1000 CK-1027 board...
Page 74 3. Open the REMOTE terminal cover, and then remove the four screws. 4. Release the hook, and then remove the outside panel. Silicon tube REMOTE terminal cover Hook Coaxial cable P2 x 4 Silicon tube Pushing directions Outside panel Arrangement of coaxial cable P2 x 4 Coaxial cable Groove...
Page 75: Vc-1046 Board
2-5. VC-1046 Board Note The following parts are not reusable. Prepare new parts in advance. • CFE radiation sheet: 1 pc Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.)
Page 76 Procedure 1. Open the elongated part of the harness guide VC, disconnect the fine-wire coaxial cable from the connector (CN0200) on the CK-1027 board and the connector (CN3502) on the VC-1046 board. 2. Release the fine-wire coaxial cable from the two notches of the harness guide VC. Notches CK-1027 board CN0200...
Page 77 3. Remove the two screws, and then remove the USB bracket. 4. Remove the four screws, and then remove the VC shield plate assembly. P2 x 6 VC shield plate assembly P2 x 6 USB bracket 5. Disconnect the two fine-wire coaxial cables, the seven flexible cables and the harness from the connectors (CN0601, CN0602, CN3200, CN4050, CN4051, CN4804, CN7500, CN8101, CN9602, CN9604) on the VC-1046 board.
Page 78 6. Release the flexible board (FP-2467) from the boss. 7. Disconnect the flexible board (FP-2464) from the connector (CN0100) on the CK-1027 board. 8. Remove the screw, and then draw the VC-1046 board about 5 mm and disconnect the B to B connectors.
Page 79 9. Remove the power shield case. 10. Peel off the seven radiation sheets. Note The CFE radiation sheet is not reusable. Radiation sheet T1 (25X25) VC-1046 board VCA radiation sheets CFE radiation sheet Power shield case 14X14 radiation sheets VCA radiation sheets sticking standard : sticking standard VC-1046 board IC (a) edge...
Page 80: Dc Fan
2-6. DC Fan Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the VC-1046 board. (Refer to “2-5. VC-1046 Board”.) Procedure 1.
Page 81 3. Remove the two screws, and then remove the fan holder. 4. Remove the DC fan assembly. Harness (RE-FAN) Boss Harness Fan holder Boss Hole Hole Label DC fan assembly P1.7 x 3 Note Install the DC fan assembly carefully paying attention to the label side and the harness position. 5.
Page 82: Front Block
2-7. Front Block Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) Procedure 1.
Page 83 2. Remove the five screws, and then front block. Front block P2.6 x 5 Note When installing the front block, tighten the screws in the following sequence: (a), (b), (c), (d), (e). 3. Install the removed parts by reversing the steps of removal.
Page 84: Cr-1006 Board
2-7-1. CR-1006 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 85 2. Disconnect the three flexible boards from the connectors (CN0100, CN0101, CN0102) on the CR-1006 board. 3. Remove the two screws, and then half turn the CR-1006 board. 4. Disconnect the flexible board (FP-312) from the connector (CN0103) on the CR-1006 board. P1.7 x 3 CN0101 CR-1006 board...
Page 86: Optical Filter Block
2-7-2. Optical Filter Block Note • Perform the following procedure in the simple cleaning bench. Wear rubber gloves during the following work. • Be sure to install the ND unit and the front section in the original combination. • Clean a new optical filter block before installing it. (Refer to “1-12. Cleaning the Optical Filter Block and the ND Unit”.) •...
Page 87 2. Remove the two screws, and then remove the E-BL assembly. Note • Do not touch the contact area. • The screws are not reusable. Contact area M1.7 x 2.2 E-BL assembly Boss Boss Hole Hole...
Page 88 3. Remove the four screws, and then remove the optical filter block. Note The screws and front OLPF packing are not reusable. M1.7 x 2.2 Holes Optical filter block Front OLPF packing Bosses Note When installing the optical filter block, tighten the screws in the following sequence: (a), (b), (c), (d). 4.
Page 89: Ck-1027 Board
2-8. CK-1027 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the VC shield plate assembly. (Refer to steps 1 to 6 in “2-5. VC-1046 Board”.) Procedure 1.
Page 90 3. Disconnect the flexible flat cable from the connector (CN1000) on the FT-2001 board. 4. Disconnect the coaxial cable from the connector (J0201) on the CK-1027 board. 5. Disconnect the two flexible boards from the connectors (CN0100, CN0102) on the CK-1027 board. Groove CN1000 CK-1027 board...
Page 91 6. Remove the three screws, and then remove the CK-1027 board. M1.7 x 3 Hole Hole CK-1027 board Boss Boss 7. Install the removed parts by reversing the steps of removal.
Page 92: If-1014 Board
2-9. IF-1014 Board Preparation 1. Remove the top cabinet. (Refer to steps 1 and 2 in “2-2. Top Cabinet, Bottom Cover”.) Procedure 1. Disconnect the flexible board from the connector (CN0102) on the CK-1027 board. 2. Remove the two screws, and then remove the IF-1014 board assembly. M1.7 x 3 Notch Flexible board...
Page 93 3. Disconnect the flexible board from the connector (CN2201) on the IF-1014 board assembly. 4. Remove the two screws, remove the IF-1014 board. Flexible board Boss IF-1014 board Hole Boss Hole CN2201 M1.7 x 3 5. Install the removed parts by reversing the steps of removal.
Page 94: Vf-1024 Board
2-10. VF-1024 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 95 3. Remove the two screws, and then remove the VF-1024 board assembly. Boss VF-1024 board assembly Hole Boss Hole P1.7 x 3 4. Disconnect the flexible board from the connector (CN1002) on the VF-1024 board. 5. Remove the two screws, and then remove the VF-1024 board. Flexible board CN1002 Boss...
Page 96: Jk-1029 Board
2-11. JK-1029 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the outside panel. (Refer to “2-4. Outside Panel”.) Procedure 1. Disconnect the harness from the connector (CN1202) on the LC-1052 board. 2.
Page 97 3. Disconnect the flexible flat cable from the connector (CN1203) on the LC-1052 board. 4. Remove the screw, and then remove the JK-1029 board assembly. JK-1029 board assembly CN1203 LC-1052 board P1.7 x 3 Flexible flat cable 5. Disconnect the flexible flat cable from the connector (CN1000) on the JK-1029 board. 6.
Page 98: Rear Assembly
2-12. Rear Assembly Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 99 4. Remove the three screws, and then remove the rear assembly. Rear assembly P2 x 4 Note When installing the rear assembly, tighten the screws in the following sequence: (a), (b), (c). 5. Install the removed parts by reversing the steps of removal.
Page 100: Tc-1002 Board
2-12-1. TC-1002 Board Note The following parts are not reusable. Prepare new parts in advance. • Tape AS: 1 pc Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3.
Page 101 Procedure 1. Peel off the tape AS. Note The tape AS is not reusable. 2. Disconnect the flexible flat cable from the connector (CN1503) on the HD-1006 board and the connector (CN5001) on the TC-1002 board. How to fold the flexible flat cable 46 mm Tape AS 37 mm...
Page 102 3. Open the SDI terminal cover. 4. Remove the two screws, and then remove the TC-1002 board assembly. TC-1002 board assembly Screw tightening sequence and attachment position SDI terminal cover P2.6 x 5 Note When installing the TC-1002 board assembly, tighten the screws in the following sequence: (a), (b). 5.
Page 103: Sdi-1004 Board
2-12-2. SDI-1004 Board Note The following parts are not reusable. Prepare new parts in advance. • Tape AS: 1 pc Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3.
Page 104 3. Open the SDI terminal cover. 4. Remove the supplied nut, and then remove the SDI-1004 board. 5. Remove the SDI shield case from the SDI-1004 board. Loctite 243 Clips SDI-1004 board Supplied nut SDI terminal cover SDI-1004 board SDI shield case Note •...
Page 105: Hd-1006 Board
2-12-3. HD-1006 Board Note The following parts are not reusable. Prepare new parts in advance. • Tape AS: 1 pc Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3.
Page 106 3. Peel off the tape AS from the SDI shield case. Note The tape AS is not reusable. 4. Disconnect the flexible flat cable from the connector (CN1503) on the HD-1006 board. Tape AS HD-1006 board CN1503 Attaching position of the Tape AS and arrangement of flexible flat cable Flexible flat cable Shield case...
Page 107 5. Open the HDMI terminal cover. 6. Remove the two screws, and then remove the HD-1006 board and the HDMI frame. HDMI frame HD-1006 board HDMI terminal cover P1.7 x 3 7. Install the removed parts by reversing the steps of removal.
Page 108: Dd-1020 Board
2-13. DD-1020 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 109: Lc-1052 Board
2-14. LC-1052 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 110: Dc-1023 Board
2-15. DC-1023 Board Preparation 1. Remove the top cabinet and the bottom cover. (Refer to “2-2. Top Cabinet, Bottom Cover”.) 2. Remove the inside panel. (Refer to “2-3. Inside Panel”.) 3. Remove the outside panel. (Refer to “2-4. Outside Panel”.) 4.
Page 111 3. Remove the shield case. DC-1023 board Clips Shield case Note After installing the shield case, make sure that the shield case is inserted all the way into the all clips. 4. Install the removed parts by reversing the steps of removal.
Page 112: Handle
2-16. Handle 2-16-1. HC-1002 Board Procedure 1. Remove the five screws. 2. Lift the handle bottom cabinet about 1 cm. Note Be careful not to damage the flexible board by lifting the handle bottom cabinet too much. 3. Remove the HC-1002 board from the hole, and then disconnect the flexible board from the connector (CN2402) on the HC-1002 board.
Page 113: Handle Top Cover Assembly
2-16-2. Handle Top Cover Assembly Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) Procedure 1. Open the microphone holder assembly. 2. Remove the two screws, and then remove the microphone holder assembly. P2.6 x 8 Microphone holder assembly 3.
Page 114 4. Remove the five screws. P2 x 4 P2 x 4 P2 x 4 Pushing directions (c)(d) P2 x 4 (c)(d) Note At the time of installation, push the parts in the direction of the arrow as shown in the figure, then tighten the screws in the following sequence: (a), (b), (c), (d).
Page 115 6. Lift the handle top cover assembly, and then disconnect the flexible flat cable from the connector (CN0402) on the HN-1054 board. 7. Pull the flexible board from the hole. Handle top cover assembly Flexible board CN0402 (HN-1054 board) Hole Flexible flat cable 8.
Page 116: Axm-1002 Board
2-16-3. AXM-1002 Board Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) 2. Remove the handle top cover assembly. (Refer to “2-16-2. Handle Top Cover Assembly”.) Procedure 1. Remove the four screws, and then remove the AXM-1002 board assembly. Positions of the XLR slide switches AXM-1002 board assembly BTP2.6 x 10...
Page 117: Hn-1054 Board
2-16-4. HN-1054 Board Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) 2. Remove the handle top cover assembly. (Refer to “2-16-2. Handle Top Cover Assembly”.) Procedure 1. Disconnect the flexible board from the connector (CN0401) on the HN-1054 board. 2.
Page 118 4. Raise the HN-1054 board and the release the two holes from the two bosses. 5. Release the two flexible boards from the three hooks. 6. Half turn the HN-1054 board. 7. Disconnect the two flexible boards from the connectors (CN0101, CN0404) on the HN-1054 board. Hole HN-1054 board Boss...
Page 119: Hs-1008 Board
2-16-5. HS-1008 Board Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) 2. Remove the handle top cover assembly. (Refer to “2-16-2. Handle Top Cover Assembly”.) 3. Remove the HN-1054 board. (Refer to “2-16-4. HN-1054 Board”.) Procedure 1. Disconnect the two flexible flat cables and the flexible board from the connectors (CN0100, CN0101, CN0102) on the HS-1008 board.
Page 120: Hk-1003 Board
2-16-6. HK-1003 Board Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) 2. Remove the handle top cover assembly. (Refer to “2-16-2. Handle Top Cover Assembly”.) 3. Remove the HN-1054 board. (Refer to “2-16-4. HN-1054 Board”.) 4. Remove the HS-1008 board. (Refer to “2-16-5. HS-1008 Board”.) Procedure 1.
Page 121 3. Disconnect the flexible flat cable from the (CN0010) on the HK-1003 board. 4. Disconnect the flexible board from the connector (CN0011) on the HK-1003 board. 5. Remove the six screws, and then remove the CNT dial assembly and the HK-1003 board. Reinforcing plate side: Flexible flat cable P2 x 4...
Page 122: Mi Shoe (Fp-310 Board)
2-16-7. MI Shoe (FP-310 Board) Preparation 1. Remove the HC-1002 board. (Refer to “2-16-1. HC-1002 Board”.) 2. Remove the handle top cover assembly. (Refer to “2-16-2. Handle Top Cover Assembly”.) 3. Remove the HN-1054 board. (Refer to “2-16-4. HN-1054 Board”.) 4.
Page 123 4. Remove the four screws, and then remove the MI shoe shell plate (88100). M1.7 x 3.3 MI shoe shell plate (88100) Note At the time of installation, apply the loctite 243 to tips of the four screws. 5. Remove the screw. 6.
Page 124 7. Pull out the flexible board of the MI shoe (FP-310 board) from the hole of the MI shoe FPC packing. MI shoe (FP-310 board) Flexible board Hole MI shoe FPC packing Note Install the MI shoe FPC packing correctly in the orientation as shown in the figure. 8.
Page 125: Panel (Vf)
2-17. Panel (VF) 2-17-1. PD-1066 Board Procedure 1. Remove the screw (P2 x 4). 2. Release the two hooks, and then remove the P harness guide. 3. Remove the two screws (TP1.7 x 5). 4. Release the two hooks, and then remove the harness guide plate. Pushing directions Hooks P harness guide...
Page 126 5. Remove the six screws. Panel P2 x 4 Pushing directions: Pushing directions P2 x 4 P2 x 4 Note At the time of installation, push the panel in the direction of the arrow as shown in the figure and tighten the screws.
Page 127 7. Remove the two screws, and then remove the hinge assembly in the direction of the arrow. P2 x 4 Hinge assembly...
Page 128 8. Disconnect the flexible boards from the connectors (CN2002, CN2005) on the PD-1066 board. 9. Disconnect the flexible flat cable from the connector (CN1000) on the PSW-1001 board. 10. Remove the four screws and lift the PD-1066 board. 11. Disconnect the connection cable from the connector (CN2001) on the PD-1066 board. 12.
Page 129: Panel Module, Psw-1001 Board
2-17-2. Panel Module, PSW-1001 Board Preparation 1. Remove the PD-1066 board. (Refer to “2-17-1. PD-1066 Board”.) Procedure 1. Pull the flexible boards from the hole of the panel frame assembly, and then remove the panel frame assembly. 2. Remove the two screws, and then remove the PSW-1001 board. Panel frame assembly Hole Hole...
Page 130 3. Pull the flexible boards from the hole of the LCD spacer (958), and then remove the LCD spacer (958). 4. Remove the panel module. LCD spacer (958) Hole Panel module Flexible boards 5. Install the removed parts by reversing the steps of removal.
Page 131: Grip
2-18. Grip 2-18-1. Exterior Parts Procedure 1. Remove the two screws, and then remove the cable cover. Cable cover P2 x 4...
Page 132 2. Remove the six screws, and then remove the grip top assembly. P2 x 4 Screw tightening sequence and Grip top assembly pushing directions P2 x 4 P2 x 4 P2 x 4 P2 x 4 P2 x 4 Note At the time of installation, push the parts in the direction of the arrow, then tighten the screws in the following sequence: (a), (b), (c), (d), (e), (f).
Page 133 3. Remove the grip button cover assembly. Grip button cover assembly 4. Remove the screw, and then remove the grip cover rear assembly. Grip cover rear assembly P2 x 4...
Page 134 5. Press the ASSIGN6 button, lift the grip cover front assembly in the direction of the arrow, and then pull it out. Grip cover front assembly ASSIGN6 button Grip cover front assembly 6. Install the grip cover rear assembly. Grip cover rear assembly...
Page 135 7. Install the grip cover front assembly, and then tighten the screw. Note When installing the grip cover front assembly, push the parts in the direction of the arrow and tighten the screw. Grip cover front assembly Pushing directions P2 x 4 8.
Page 136: Uif-1001 Board, Uc-1001 Board
2-18-2. UIF-1001 Board, UC-1001 Board Preparation 1. Remove the exterior parts. (Refer to “2-18-1. Exterior Parts”.) Procedure 1. Disconnect the grip cable (3.5 STEREO) from the connector (CN2001) on the UIF-1001 board. 2. Remove the three screws, and then remove the grip PWB cover B. Grip cable Arrangement of harnesses (3.5 STEREO)
Page 137 5. Disconnect the flexible flat cable from the connector (CN2005) on the UIF-1001 board. 6. Remove the two screws, and then remove the UIF-1001 board. Arrangement of flexible flat cable UIF-1001 board Flexible flat cable CN2005 P2 x 4 Flexible flat cable Note At the time of installation, arrange the flexible flat cable as shown in the figure.
Page 138: Section 3 Error Code
Section 3 Error Code If a problem occurs during operation of the unit, an error code will appear in the viewfinder display. Check the details of the error code and respond accordingly. 3-1. Error Code List Error Description Check and Action code Check: ND unit, IC6502 (CR-1006 board), IC1000 (VC-1046 board),...
Page 139 Error Description Check and Action code Check: IC1000 (VC-1046 board), IC0301 (KY-1031 board), and the Communication error between peripheral devices. E91-380 IC1000 (VC-1046 board) and Action: • Replace the flexible flat cables, flexible boards, and harnesses IC0301 (KY-1031 board) that connect the boards. •...
Page 140 Error Description Check and Action code Check: IC1000, IC8000 (VC-1046 board), and the peripheral devices. Communication error from IC1000 Action: • Replace the flexible flat cables, flexible boards, and harnesses E95-315 (VC-1046 board) to IC8000 that connect the boards. (VC-1046 board) •...
Page 141: Section 4 Service Menu
Section 4 Service Menu 4-1. Overview The unit is provided with the Service menu that is useful for maintenance and adjustment. The menu content is displayed on the viewfinder. The Service menu consists of the following menus. Menu Item Description Auto/manual RPN registration, deletion, and automatic detection Factory Reset Resets all settings of the unit to the factory default.
Page 142: Service Menu List
4-3. Service Menu List Menu Item Submenu Item Choice Function Reflection of setting Execute / Cancel Executes the automatic defect Starts after “Execute” is correction function (automatic selected pixel noise reduction) Reset Execute / Cancel Deletes all the concealment Starts after “Execute” is targets registered by APR.
Page 143: Operation Log
4-5. Operation Log This unit can acquire the AllFile file and the following operation log using the Log Dump function. • Button/switch operation log • Menu setting log • Peripheral device connection log Each time the power switch on the unit is turned off, the operation log file and the AllFile file are stored. However, these files are not stored if the battery pack is removed or the cable is disconnected from the DC IN connector while the power switch is turned on.
Page 144: Operation Log File/Allfile File Storage Location
4-5-2. Operation Log File/AllFile File Storage Location Insert the SD card that contains the operation log file into the SD card slot on the PC. Check that the file exists in the following folder using the explorer or other applications. SD (D:) 20201014_145346.txt AllFile.ALL...
Page 145 Checking the operation log file Open the operation log file using a text editor (such as Notepad). 14:53:46 [K] VF PEAKING (RELEASE) 14:53:46 [K] VF ASSIGN9 (RELEASE) 14:53:46 [K] VF MIRROR OFF 14:53:46 [K] FOCUS(AUTO) 14:53:46 [C] Handle I/F connected 14:53:46 [C] Media Eject SlotA 14:53:46 [C] Media Insert SlotB 14:53:46 [C] Grip remote connected...
Page 146: Section 5 Spare Parts
Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2. Standardization of Parts 2. 部品の共通化 Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は，セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.
Page 147: Exploded Views
5-2. Exploded Views Overall Handle-1 P2.6 x 5 Panel (VF) -1 Outside Panel Grip-1 UC, CEE, CN1, IN5, E38, AF1, AP2 Charger Part No. SP Description 2-630-005-31 s SCREW(M2),NEW TRUSTER,P2 4-269-040-01 s HOOK, MEGEYAR 4-540-533-01 s FOOT (941), RUBBER 4-579-210-02 s HANDLE CONNECTOR COVER 4-579-745-01 s CLAMP (964), CABLE 4-587-420-01 s LID, BM 4-737-449-01 s TUBE, SILICON (1.3)
Page 148: Outside Panel
Outside Panel VC Board Inside Panel-1 Part No. SP Description A-5020-540-A s WF-12A MOUNT A-5028-087-A s SERVICE, CABINET, OUTSIDE 1-846-474-31 s CABLE, COAXIAL (110MM) 2-630-005-31 s SCREW(M2),NEW TRUSTER,P2 2-635-562-21 s SCREW(M1.7) 3-080-204-01 s SCREW, TAPPING, P2 4-737-449-01 s TUBE, SILICON (1.3) 5-015-265-01 s TALLY, FRONT 5-015-267-01 s HOLDER, WIFI OUT 5-015-781-01 s SHEET,FRONT WP...
Page 149: Vc Board
VC Board DC Fan Front Block P2 x 6 P2.6 x 5 P2 x 6 P2 x 6 Part No. SP Description A-5025-549-A s VC-1046 COMPL 1-006-662-11 s FP-2464 FLEXIBLE PWB 1-007-993-11 s HARNESS(VC-CK-20P) 5-008-781-01 s SHEET T1(25X25), RADIATION E11 5-015-197-01 s VC SHIELD PLATE 5-015-198-01 s SHIELD CASE, POWER 5-015-199-01 s BRACKET, USB...
Page 150: Dc Fan
DC Fan CK/IF/VF Boards P2.6 x 5 Part No. SP Description X-5001-350-1 s VC HEATSINK ASSY X-5001-351-1 s IMG HEATSINK ASSY X-5001-352-1 s CFE HEATSINK ASSY 1-855-374-11 s DC FAN 2-635-562-21 s SCREW(M1.7) 4-576-418-02 s SCREW, TRIPOD 4-736-984-01 s CUSHION, FAN 5-015-744-01 s HOLDER, FAN 5-015-746-01 s DUCT PACKING, IN 5-015-748-01 s SHEET,MAIN FLAME...
Page 151: Ck/If/Vf Boards
CK/IF/VF Boards To VC-1046 board Main Frame Rear Block Part No. SP Description A-5013-566-A s IF-1014 MOUNT A-5013-571-A s JK-1029 MOUNT A-5013-575-A s VF-1024 MOUNT A-5013-588-A s CK-1027 MOUNT A-5013-589-A s FT-2001 MOUNT 1-002-371-11 s CABLE, FLEXIBLE FLAT (8 CORE) 1-006-663-11 s FP-2465 FLEXIBLE PWB 1-006-664-11 s FP-2466 FLEXIBLE PWB 1-754-972-13 s NFC ANTENNA...
Page 152: Main Frame
Main Frame To Harness (RE-FAN) To VC-1046 board To VC-1046 board Part No. SP Description A-5013-560-A s DD-1020 MOUNT A-5013-574-A s LC-1052 MOUNT A-5013-899-A s DC-1023 MOUNT A-5028-084-A s SERVICE, BUTTON, RELEASE BT X-2591-961-1 s PIN ASSY, GP MOUNT LOCK 1-006-666-11 s FP-2468 FLEXIBLE PWB 1-780-986-11 s TERMINAL BOARD, BATTERY 1-969-447-12 s HARNESS, SUB (RE-CN)
Page 153: Inside Panel-1
Inside Panel-1 Inside Panel-2 To VC-1046 board Part No. SP Description A-5013-562-A s HP-1015 MOUNT A-5013-578-A s KY-1031 MOUNT A-5013-584-A s PS-1004 MOUNT A-5015-455-A s SEL-1001 MOUNT 1-002-371-11 s CABLE, FLEXIBLE FLAT (8 CORE) 1-002-415-11 s SWITCH BLOCK CONTROL(AU95700) 1-006-667-11 s FP-2469 FLEXIBLE PWB 1-007-990-11 s CABLE, FLEXIBLE FLAT (24CORE) 1-471-573-21 s MAGNET 1-542-979-11 s MICROPHONE, ELECTRET CAP...
Page 154: Inside Panel-2
Inside Panel-2 Inside Panel-3 Part No. SP Description A-5013-579-A s FU-1001 MOUNT A-5013-582-A s TG-1005 MOUNT A-5013-583-A s SH-1030 MOUNT A-5013-586-A s WB-1002 MOUNT 1-002-414-11 s SWITCH BLOCK,CONTROL (ID95700) 1-912-734-11 s CABLE, FLEXIBLE FLAT (6 CORE) 2-635-562-21 s SCREW(M1.7) 3-080-206-21 s SCREW, TAPPING, P2 4-431-734-01 s TAPE AS 5-008-684-01 s DIAL, MULTI FUNCTION 5-008-748-01 s PACKING, TOGLLE...
Page 155: Inside Panel-3
Inside Panel-3 Inside Panel-4 To CK-1027 board Part No. SP Description A-5013-580-A s SS-1007 MOUNT A-5013-581-A s SW-1037 MOUNT A-5013-585-A s VSW-1001 MOUNT A-5020-539-A s WF-1008A MOUNT 1-756-134-18 s BATTERY, LITHIUM (SECONDARY) 1-846-474-21 s CABLE, COAXIAL (85MM) 1-912-734-11 s CABLE, FLEXIBLE FLAT (6 CORE) 2-635-562-21 s SCREW(M1.7) 3-080-206-21 s SCREW, TAPPING, P2 4-299-985-11 s RUBBER, SS...
Page 156: Inside Panel-4
Inside Panel-4 Part No. SP Description A-5028-085-A s SERVICE, CABINET, INSIDE A-5028-086-A s SERVICE, LEVER, MEDIA LID X-5001-833-1 s LID ASSY(958)_AU 3-080-206-21 s SCREW, TAPPING, P2 4-165-324-01 s SHAFT, AL 5-009-176-01 s CUSHON, MEDIA LID A 5-015-206-01 s PLATE, MEDIA LOCK 5-015-239-01 s LID, MEDIA 5-015-240-01 s WINDOW, MEDIA 5-015-262-01 s TERMINAL COVER, HP...
Page 157: Front Block
Front Block 1011 1012 1002 1010 1013 P2 x 6 1018 1019 1004 1020 1005 1015 1014 1006 1003 1016 To VC-1046 board To VC-1046 board 1007 1022 To VC-1046 board P2 x 6 1017 1021 1009 1008 1001 To VC-1046 board Part No.
Page 158: Rear Block
Rear Block 1119 1117 1113 1111 1107 1108 1118 1118 1110 1115 To VC-1046 board 1108 1101 To VC-1046 board 1114 1104 1105 1106 P2.6 x 5 1109 1116 To VC-1046 board 1120 1103 1112 P2.6 x 5 1102 Part No. SP Description 1101 A-5013-558-A s HD-1006 MOUNT...
Page 159: Handle-1
Handle-1 1216 1202 1219 P2.6 x 8 1203 1207 1218 1212 1211 1217 Handle-2 1214 1218 1215 1213 1224 1224 1206 1205 1205 1222 1222 1223 1223 1221 1204 1209 1225 1201 1225 1209 W6, MIDDLE 1210 1210 1220 W6, MIDDLE 1208 1204 1204...
Page 160: Handle-3
Handle-2 1306 1312 1309 1303 1305 1303 1317 1310 1316 1303 Handle-3 1308 1303 1301 1303 1302 1313 1304 1314 1311 1315 BTP2.6 x 10 1303 1307 Part No. SP Description 1301 A-5013-561-A s AXM-1002 MOUNT 1302 1-007-989-11 s CABLE, FLEXIBLE FLAT (30CORE) 1303 2-630-005-31 s SCREW(M2),NEW TRUSTER,P2 1304...
Page 161 Handle-3 To HC-1002 board 1424 1414 1433 1408 1412 1420 1402 1415 1416 1407 1412 1404 1411 1410 1412 1428 1417 1412 1403 1406 1427 1419 1413 1405 1421 1441 1423 1418 1422 1440 1439 1432 1412 1431 1436 1435 1434 1429 1430...
Page 162 Part No. SP Description 1401 A-5002-389-A s FP-310 MOUNT 1402 A-5013-567-A s HN-1054 MOUNT 1403 A-5013-568-A s HS-1008 MOUNT 1404 A-5013-569-A s HK-1003 MOUNT 1405 A-5014-088-A s DL-1007 MOUNT 1406 X-5001-720-1 s CNT DIAL ASSY (95800) 1407 1-002-371-11 s CABLE, FLEXIBLE FLAT (8 CORE) 1408 1-006-668-11 s FP-2470 FLEXIBLE PWB 1409...
Page 163: Panel (Vf) -1
Panel (VF) -1 1507 1503 1507 1514 1521 Panel (VF) -2 1508 1510 1516 1517 1520 1524 1519 1507 1513 1504 1511 1523 1522 1507 1515 1507 1502 1506 1501 1523 1509 1512 1505 1518 1507 Part No. SP Description 1501 A-5013-576-A s PD-1066 MOUNT 1502...
Page 164: Panel (Vf) -2
Panel (VF) -2 1602 1605 1602 1604 1606 1614 1615 1602 1601 1611 1613 1613 W6, MIDDLE 1607 1616 1610 1603 W5, MIDDLE 1612 1609 1608 1602 1611 Part No. SP Description 1601 X-2591-959-3 s HINGE (964) ASSY 1602 2-630-005-31 s SCREW(M2),NEW TRUSTER,P2 1603 2-635-562-21 s SCREW(M1.7) 1604...
Page 165: Grip-1
Grip-1 1704 1720 1704 1721 1701 1718 1707 1715 1711 1725 1714 1704 1717 1704 1716 1706 1704 1719 1721 1704 1703 1713 1724 Grip-2 1704 WASHER 20, WAVE 1704 1704 1710 1722 1708 1712 1705 1723 1709 1706 1702 1704 Part No.
Page 166 Grip-2 1823 1810 1826 1807 1811 1805 1813 1801 1804 1806 1822 1812 1819 1811 1816 1811 1811 1815 1802 1811 1812 1811 1820 1811 1803 1821 1814 1809 1811 1824 1808 1817 1811 1825 1818 1811 1812...
Page 167 Part No. SP Description 1801 A-5002-413-A s FP-311 MOUNT 1802 A-5013-572-A s UC-1001 MOUNT 1803 A-5025-557-A s UIF-1001 COMPL 1804 A-5028-088-A s SERVICE, CHASSIS, GRIP 1805 A-5028-147-A s SERVICE, LEVER, ROTARY LOCK 1806 A-5028-148-A s SERVICE, PIN, ROTATION LOCK 1807 X-2590-703-4 s DIAL ASSY (786), CONT 1808 1-002-365-11 s CABLE, FLEXIBLE FLAT (6 CORE)
Page 168: Charger (Uc, Cee, Cn1, In5, E38, Af1, Ap2)
Charger (UC, CEE, CN1, IN5, E38, AF1, AP2) 1904 1908 1901 1905 1904 1902 1909 1903 1904 1906 1907 Part No. SP Description 1901 A-5025-162-A s CHARGER BLOCK ASSY 1902 A-5025-558-A s CHG-1003 COMPL 1903 1-780-986-11 s TERMINAL BOARD, BATTERY 1904 3-080-204-21 s SCREW, TAPPING, P2 1905...
Page 169: Supplied Accessories
5-3. Supplied Accessories Q'ty Part No. SP Description A-5025-162-A s CHARGER BLOCK ASSY X-2188-877-5 s COLD SHOE KIT 1-003-907-12 s LITHIUM ION BATTERY PACK [For UC,CEE,IN5,AF1,E38,AP2] 1-003-907-21 s LITHIUM ION BATTERY PACK [For CN1] 1-493-482-32 s AC ADAPTOR (60W) 1-912-358-12 s CABLE, USB X-2593-938-1 s HOOD ASSY (956), LCD 4-580-791-01 s HOOD, LCD Power supply cords...
Page 170 I type 1-837-429-53 1-846-095-32/1-846-430-34 Any of the following power supply cords can be used. 1-837-429-53 s CORD SET, POWER-SUPPLY 1-846-095-32 s CORD SET, POWER-SUPPLY 1-846-430-34 s CORD SET, POWER-SUPPLY G type(BF type) Any of the following power supply cords can be used. 1-837-421-54 s CORD SET, POWER-SUPPLY 1-848-678-22 s POWER-SUPPLY CORD SET...
Page 171: Section 6 Diagrams
Section 6 Diagrams Overall Overall (1/5) IC8000(1/5) SDI-1004 X8501 FPGA 148.351648MHz CN8101 CN6001 IC6004 (MONI)2(SDI)_ X8502 TXP0/TXN0 (MONI)2(LMH1228)_TXP/N 148.5MHz (MONI)2(LMH1228)_ J6002 I2C_SDA/SCL I2C_SDA/SCL DRIVE 12G-SDI IC8504 148M X8503 LVDS +3.3V_SDI D_3.3V_R2 148.5MHz IC8503 (CETU)2(MONI)_IOE_RST_X VF-1024 PD-1066 (CETU)2(MONI)_IOE_RST_AU_FPGA_X IS-1043 VC-1046(1/5) IC1000 CN7500 CN1002 (1/5)
Page 172 Overall (2/5) VC-1046(2/5) HD-1006 CN1501 CN1504 IC1503 D0-2;/- TMDS_DATA0-2+/- CLK+/- HDMI TMDS_CLOCK+/- RETIMER HDMI_ IC2000 IC1000 RETIMER_ (2/5) (2/5) SDA/SCL HDMI C_REC_V CN4050 TO/FROM CAMERA C_STM_V HDMI_DATA0-2P/N CN1502 (MIRA) SIGNAL TMDS181_EN SDA/SCL LLC_V/H HDMI_CLKP/N PROCESSOR (CETUS) M2C_INT0-2 C2M_INT0-2 IC1511 HDMI_SDA_CN DDC_SDA/SCL HDMI_SCL_CN BUFFER...
Page 173 Overall (3/5) HC-1002 IF-1014 AXM-1002 HN-1054 MICROPOHNE UNIT CN0404 CN0401 CN2402 CN2401 CN2202 CN2201 IC0202 IC0204 FP-2470 FP-2465 INT_MIC_L/R (INT_HND)2(MONI)_I2S_DATA CN0402 IC1002 256FS_BUF2 IC0301 (XLR)2(MONI)_I2S_DATA IC0302 (MONI)2(INT) (MONI)2(AU)_64FS_BUF2 FROM _RST_X (MONI)2(AU)_FS_BUF2 S3000:INPUT1 CN0402 IC0104 S3001:INPUT2 256FS_BUF2 (XLR)2(MONI)_I2S_DATA (XLR)2(MONI)_I2S_DATA (MONI)2(AU)_64FS_BUF2 IC1000 Q1004,Q1005 CN1000 (1/2)
Page 174 Overall (4/5) WB-1002 VSW-1001 KY-1031 VC-1046(4/5) IC1000 (4/5) CN1000 CN0100 CN0104 CN0105 CN0100 CN9603 PUSH C_ADC0_VIN2_ISO_GAIN C_ADC0_VIN2_FOCUS_PUSH_A CL0001-CL0006 (KY)2(CTS)_ CAMERA CL0003 (KY)2(CTS)_AUVR_CH1/2 (KY)2(CTS)_AUVR_CH1/2 (KY)2(CTS)_AUVR_CH1-2 AUTO C_ADC0_VIN0 CONTROL SIGNAL CL0004 ND+/- SWITCH PROCESSOR (KY)2(CTS)_C_ADC0_VIN0,1,2,4 ND AUTO BLOCK (CETUS) IC2000 FOCUS_PUSH_A_CN C_ADC0_VIN1_WBSET (KY)2(CTS)_C_ADC1_VIN7 CL0001 WB SET...
Page 175 Overall (5/5) DC-1023 DD-1020 VC-1046(5/5) Q101 CN101 CN1001 Q2010,Q2011 J101 DC_19.5V RECONNECT F101 SWUNREG_20V_10V IC0900 DC IN PROTECT CN1003 CN9801 (4/4) Q2008,Q2009 Q2012,Q2013 (DWN)_L_POWER_SAVE (DWN)_L_POWER_SAVE (DWN)_L_POWER_SAVE UNREG_CHARGER_OUT (DARWIN) DC_19.5V_OUT DC_12V_OUT DC_12V_OUT IC2003 IC2008 POWER OCP_ACV CURRENT CONTROL SENSOR IC2004 ACV_ACTIVE ACV_ACTIVE ACV_ACTIVE ACV_UVP_ADJUST...
Page 176 Frame Wiring WF-12A WF-1008A PSW-1001 TC-1002 CN001 JK-1029 UIF-1001 MULTI INTERFACE MICROPOHNE FP-311 SHOE WIRELESS WIRELESS UNIT J5201 GRIP CABLE LAN ANTENNA LAN ANTENNA TC IN/OUT (3.5 STEREO) CN5001 J7391 J7391 DC FAN CN1000 PH001,PH002 PEAKING ZEBRA ASSIGN FP-310 ASSIGNABLE DIAL(GRIP) SDI-1004 CN1000...
Page 177 Revision History Date History Contents 2020. 11 1st Edition ― 9-932-769-01...
Page 178 ILME-FX6V (UC) ILME-FX6V (J) ILME-FX6V (CEE) ILME-FX6V (CN1) ILME-FX6V (IN5) ILME-FX6V (E38) ILME-FX6V (AP2) ILME-FX6VK (UC) ILME-FX6VK (J) ILME-FX6VK (CN1) ILME-FX6T (UC) ILME-FX6T (CEE) ILME-FX6T (AF1) ILME-FX6TK (UC) Printed in Japan ILME-FX6TK (CEE) J,E 2020. 11 08 Sony Corporation 9-932-769-01 ©...

This manual is also suitable for:

Ilme-fx6vk Ilme-fx6t Ilme-fx6tk

Sony ILME-FX6V Service Manual

Section 1 Service Overview

Section 2 Replacement of Parts

Section 3 Error Code

Section 4 Service Menu

Section 5 Spare Parts

Section 6 Diagrams

Quick Links

Related Manuals for Sony ILME-FX6V

Summary of Contents for Sony ILME-FX6V

This manual is also suitable for:

Table of Contents