Contents Introduction..............2 Troubleshooting............14 Safety................4 Transportation, storage and disposal......15 Assembly................ 9 Technical data.............. 17 Operation..............10 Accessories..............18 Maintenance..............12 Declaration of Conformity..........20 Introduction Product description For concrete layers maximum 100 mm thick, no other vibration method is necessary before you use the The product is a walk-behind concrete screed with product.
Page 3
Product overview 15 16 Symbols on the product 1. Beam 2. Battery WARNING: This product can be 3. Frame dangerous and cause serious injury or 4. Display death to the operator or others. Be careful 5. Battery indicator and use the product correctly. 6.
1. Product type 2. IP classification 3. Rated voltage Use protective gloves. 4. Product weight 5. Rated power 6. Production year 7. Manufacturer Lifting point on the product. 8. Serial number 9. Product number Product liability This product is in compliance with applicable EC directives.
Page 5
Power tool use and care • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and • Do not force the power tool. Use the correct power refrigerators. There is an increased risk of electric tool for your application. The correct power tool will shock if your body is earthed or grounded.
Page 6
• Do not use a battery pack or tool that is damaged or • Make sure that the battery voltage agrees with the modified. Damaged or modified batteries may exhibit voltage that is given on the rating plate of the unpredictable behavior resulting in fire, explosion or product.
Page 7
Do a check of the safety devices regularly. If the where it cannot cause dust to go into the air. safety devices are defective, speak to your Husqvarna service agent. Noise safety To do a check of the power trigger...
Page 8
The vibration damping units decrease harmful • Do not use other battery chargers than the one vibrations to prevent injury to the operator and damage supplied for your product. Only use Husqvarna QC to the product. chargers when you charge Husqvarna replacement batteries BLi.
• If you do not do maintenance, it decreases the life are approved after you have done maintenance, turn cycle of the product and increases the risk of to your servicing dealer. We guarantee that there are accidents. professional repairs and servicing available for your product.
To connect the battery to the product WARNING: WARNING: Read and understand the Only use Husqvarna safety chapter before you use the product. original batteries in the product. To do before you operate the product 1. Make sure that the battery is fully charged.
Page 11
To start the product CAUTION: If you use too much vibration force, slurry can collect on the 1. Connect the battery to the product. surface. If you use too low vibration 2. Push and hold the ON/OFF button (A) until the force, it is possible that all air bubbles battery indicator (B) comes on.
To stop the product c) Put the end of the beam on each of the parallel strips and operate the product (C). Make sure 1. Release the power trigger. that the beam follows the contour of the parallel strips. 2. Push and hold the ON/OFF button until the display LED goes off.
Page 13
Maintenance schedule Maintenance Daily Weekly Monthly Clean the product. Make sure that the ON/OFF button operates correctly and is not damaged. Make sure that the power trigger operates correctly from a safety point of view. To do a check of the power trigger on page 7 Refer to Make sure that there is no oil and grease on the handles, and that they are dry and clean.
ON/OFF button. connector. is correctly assembled. The user interface is broken. Speak to your Husqvarna service agent. The cables between the control unit and Speak to your Husqvarna service agent. the user interface are damaged. Short circuit in the control unit.
Symptom Possible causes Recommended step The vibration bearings are damaged. Speak to your Husqvarna service agent. The noise level is too The handle knobs are not sufficiently Tighten the handle knobs. high. tightened. The vibration frequency is not correct for Adjust the vibration speed to make the vibra- this concrete surface.
Page 16
electrical and electronic equipment. This helps to prevent damage to the environment and to persons. Speak to local authorities, domestic waste service or your dealer for more information. Note: The symbol shows on the product or package of the product. 1493 - 001 - 27.05.2021...
Technical data Technical data Weight without battery, kg/lb 11.5/25 Motor brand / Type Husqvarna / 36V Motor power, kW/hp @rpm 0.8/1.1 @7500 Noise and vibration emissions Sound power level, measured dB (A) Sound pressure level at the operator's ear, L...
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, SWEDEN, Tel: +46 36 146500 declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BV 30i Identification Serial numbers dating from 2021 and onwards...
Page 21
UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, SWEDEN, Tel: +46 36 146500 declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BV 30i Identification Serial numbers dating from 2021 and onwards...