Page 1
NETWORK CAMERA SNC-DS10 SNC-DM110 SERVICE MANUAL 1st Edition (Revised 1)
Page 2
à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. When using a modular jack cable: For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage. SNC-DS10/DM110...
..Installation Manual (Supplied with SNC-DS10/DM110) This manual describes the information on installing the SNC-DS10/DM110..“Easy Setup Guide for the Sony Network Camera ” CD-ROM (Supplied with SNC-DS10/DM110) This manual describes the information on setting the SNC-DS10/DM110.
Service Overview 1-1. Board Location 1-2. Replacing the Main Parts 1-2-1. Upper Case N Assembly BI-222 board (SNC-DS10) BI-224 board (SNC-DM110) 1. Remove the cover using a tool such as a flat screw- driver. 2. Remove the stepped screw (with stopper), then remove...
SY-358 C216 12 years time. The printed pattern (copper foil) may peel away if C217 8 years the heated tip is applied for too long, so be careful. PS-744 SWR1 (AC-DC converter) 14 years SNC-DS10/DM110...
J-7120-450-A: Gray scale chart I type (For PTB-700) J-6431-850-A: Pattern box PTB-700 . Light source for test chart SNC-DM110 J-7120-480-A: Vectorscope scale (Mega) SNC-DS10 J-7120-490-A: Vectorscope scale (SD) J-6080-058-A: Color temperature correction filter C14 . For the color reproduction adjustment (This scale is printed on the Appendix.) .
75 Z termination Personal computer Only SNC-DM110 Remove the upper case and board cover of this unit, and then connect the positive terminal to TP801 on the SY-358 board and connect the negative terminal to TP101 on the SY-358 board. SNC-DS10/DM110...
1. Connect each equipment according to the connection diagram in Section 2-1-3. 2. Turn on the power of each device. In the case of SNC-DS10 3. Click “CameraAdjustmentTool.exe” to start the camera adjustment software. 4. Type the IP address of camera, and then click the [Connect] button.
. Measurement device: Voltmeter . Specification: Displayed in the lower portion of the adjustment software window. 1. Select the letter imprinted on the backside of CCD (“f” in the above picture), then click the [OK] button. List box Specificaion SNC-DS10/DM110...
3. Check that “OK” is displayed in the upper right area of 3. Check that “OK” is displayed in the upper right area of the window, and then click the [Next] button. the window, and then click the [Next] button. Spin box Spin box SNC-DS10/DM110...
3. Check that “OK” is displayed in the upper right area of the window, and then click the [Next] button. 4. Remove the cover (lens cap, etc.) from the lens. 4. Remove the cover (lens cap, etc.) from the lens. SNC-DS10/DM110...
C. the window, and then click the [Next] button. 3. Click the [OK] button. 4. Check that “OK” is displayed in the upper right area of the window, and then click the [Next] button. Spin box SNC-DS10/DM110...
1. Check that the luminescent spot stays near the center of vectorscope, and then click the [3200K] button. 2. Put the color temperature correction filter C14 over the lens. 3. Check that the luminescent spot stays near the center of vectorscope, and then click the [5800K] button. SNC-DS10/DM110...
1. Check that the luminescent spot stays near the center of vectorscope, and then click the [3200K] button. 2. Put the color temperature correction filter C14 over the lens. 3. Check that the luminescent spot stays near the center of vectorscope, and then click the [5800K] button. SNC-DS10/DM110...
3. Adjust the sixteen spin box values so that all lumines- cent spots on the vectorscope stay within the color reproduction frame. Adjust R (red), YL (yellow), G (green) and Cy (cyan) so that they stay within the inner small frame. 4. Click the [OK] button. 2-10 SNC-DS10/DM110...
Color-bar chart 3. After checking that the display returned to the startup . Measuring equipment: Vectorscope . Specification: window, turn off the power of this unit. All luminescent spots should stay within the large frame of the vectorscope scale. 2-11 SNC-DS10/DM110...
Network port (straight) 2-4-1. Re-sticking of MAC Address Label Camera Replace the MAC address label on the bottom of the unit LAN cable with the new label supplied with the new SY-358 board. (cross) LAN cable (straight) Personal computer 2-12 SNC-DS10/DM110...
Page 25
. The factory default IP address of the unit is set to 9. Start up the IP Setup Program in the CD-ROM “192.168.0.100”. supplied to the unit, check the model name, and check that the correct Mac address and serial number are written. (Refer to the User’s Guide.) 2-13 SNC-DS10/DM110...
CPU (IC101). A system clock is 27 MHz. It is supplied from X103. A camera signal processing clock is supplied as follows: . For SNC-DS10, a clock is 24.545 MHz and supplied from X102. . For SNC-DM110, a clock is 36 MHz and supplied from the BI-224 board.
Data is read and written from IC603 between IC601 and main CPU (IC101) through buffer IC605. The software stored in flash memory can be upgraded via a network. SNC-DS10/DM110...
1 and 2 of an AC/DC converter (SWR1) through the fuse (F1) and line filter (LF1) on the PS-744 board. The fuse (F1) blows out to interrupt an overcurrent when the current supplied to the AC/ DC converter (SWR1) steadily exceeds 2.5 A. SNC-DS10/DM110...
Page 30
5 V used in peripheral circuits and DD3. DD3 converts each voltage from the supplied 5 V voltage to +15 V and _5.5 V (SNC-DS10) or _8.5 V (SNC-DM110) used in the CCD and timing generator blocks on the BI-222 and BI-224 boards. Each output voltage of DD1 to DD3 is determined by the values of resistors R5 to R20 connected to DD1 to DD3.
Is the correct voltage (+15 V/_8.5 V or _5.5 V) output Replace DD3. from DD3 (pin 11/pin 8) of the PS board respectively? Is the symptom improved by replacing with another Replace the BI board. SY board? Replace the SY board. SNC-DS10/DM110...
. Pin 10: 2.5 V in color, corrosion, etc.) Failure of IC301 and peripheral Replace CN301. circuit on the SY board. Replace the defective parts. Failure of DD1 and peripheral circuit on the PS board. Replace the defective parts. SNC-DS10/DM110...
4-3. Image is not displayed on the PC viewer Image is not displayed *1: SNC-DM110 on the PC viewer. *2: SNC-DS10 *3: 1-966-137-11: BI board, CN101 5 SY board, CN808 Can it be connected Refer to “4-2. Cannot connect to the network”.
Wipe off the contamination contamination on the lens Noticeable black spots on the CCD and optical filter. and dome cover? Is the resolution changed when the setting of Set the sharpness Low resolution [Camera]-[Picture]-Sharpness properly. is changed? To page 4-5 SNC-DS10/DM110...
Page 35
Is [Camera]-[Common]- Abnormal color No color Color set to “Color”? Change the color setting to “Color”. In the case of SNC-DS10 Abnormal color Inverted hue In the case of SNC-DM110 Failure of harness (coaxial Is the symptom changed cable (*1)), CN101 on the Adjust the VSUB voltage.
Replace the defective parts. Failure of CN810, R218, Does the video signal exist FL801 or D817 on the SY board. between pin 1 and pin 2 Replace the defective parts. of CN810 on the SY board? Replace the connecting cord (for video). SNC-DS10/DM110...
(bending of pin, change in color, Replace the defective parts. . Pin 8: 1.2 V corrosion, etc.) Failure of RY801, RY802 and Replace the I/O Replace CN806. peripheral circuit on the SY board. (input/output) cable. Replace the defective parts. SNC-DS10/DM110...
Failure of DD2 and peripheral circuit on the PS board. to CN801 on the SY board? . Pin 3: 5 V Replace the defective parts. Failure of IC701, IC702 and peripheral circuit on the SY board. Replace the defective parts. SNC-DS10/DM110...
. Pin 6: 3.3 V (bending of pin, change in Replace the defective parts. . Pin 8: 1.2 V color, corrosion, etc.) Failure of IC702 and peripheral Replace the audio cable. Replace CN805. circuit on the SY board. Replace the defective parts. SNC-DS10/DM110...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. 3. Stock of Parts Parts marked with “o”...
A-3. Electrical Parts List ------------------------------------------ BI-222 BOARD FOR SNC-DS10(SY)/SNC-DS10(CN) (BI-222 BOARD FOR SNC-DS10(SY)/SNC-DS10(CN)) ------------------------------------------ Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description A-1358-939-A s MOUNTED CIRCUIT BOARD, BI-222 FB104 1-469-667-21 s FERRITE, EMI (SMD) (1608)
Page 46
1-208-927-81 s RES, CHIP 47K (1005) C168 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 R121 1-208-927-81 s RES, CHIP 47K (1005) R122 1-208-925-81 s RES, CHIP 39K (1005) C169 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) R124 1-208-935-81 s RES, CHIP 100K (1005) SNC-DS10/DM110...
Page 47
------------ (BI-224 BOARD FOR SNC-DM110(SY)) PS-744 BOARD ------------ Ref. No. or Q'ty Part No. SP Description *a:[SNC-DS10(SY)/SNC-DS10(CN)] *b:[SNC-DM110(SY)] R125 1-208-935-81 s RES, CHIP 100K (1005) R126 1-208-945-81 s RES, CHIP 270K (1005) Ref. No. R127 1-218-977-81 s RES, CHIP 100K or Q'ty Part No.
Page 48
------------ (PS-744 BOARD) SY-358 BOARD ------------ Ref. No. or Q'ty Part No. SP Description *a:[SNC-DS10(SY)/SNC-DS10(CN)] *b:[SNC-DM110(SY)] 1-218-990-81 s CONDUCTOR, CHIP (1005) 1-208-905-81 s RES, CHIP 5.6K (1005) Ref. No. 1-208-927-81 s RES, CHIP 47K (1005) or Q'ty Part No. SP Description...
Page 49
1-162-964-91 s CAP,CHIP CERAMIC 1000PF B 1608 C329 1-112-317-11 s CAP, CHIP CERAMIC 0.1MF (2012) C533 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) C330 1-112-317-11 s CAP, CHIP CERAMIC 0.1MF (2012) C534 1-162-964-91 s CAP,CHIP CERAMIC 1000PF B 1608 SNC-DS10/DM110...
Page 50
1-400-382-21 s EMI FERRITE (SMD) (1608) C818 1-100-566-91 s CAP, CHIP CERAMIC 0.1MF B 1608 FB202 1-400-382-21 s EMI FERRITE (SMD) (1608) C819 1-100-566-91 s CAP, CHIP CERAMIC 0.1MF B 1608 FB301 1-400-382-21 s EMI FERRITE (SMD) (1608) A-10 SNC-DS10/DM110...
Page 51
1-218-937-81 s RES, CHIP 47 *b 6-808-266-01 s IC S29GL256N90TFIR20-DM110V100 IC603 8-759-392-81 s IC SN74LVC16245ADGGR R124 1-218-446-91 s RES, CHIP 1 (1608) R125 1-218-977-81 s RES, CHIP 100K IC604 8-759-392-81 s IC SN74LVC16245ADGGR R126 1-218-953-81 s RES, CHIP 1.0K A-11 SNC-DS10/DM110...
Page 52
1-218-965-81 s RES, CHIP 10K R186 1-218-933-81 s RES, CHIP 22 R444 1-218-965-81 s RES, CHIP 10K R187 1-218-935-81 s RES, CHIP 33 R451 1-218-990-81 s CONDUCTOR, CHIP (1005) R188 1-218-935-81 s RES, CHIP 33 R452 1-218-990-81 s CONDUCTOR, CHIP (1005) A-12 SNC-DS10/DM110...
Page 53
1-234-381-21 s RES, NETWORK 100K (1005X4) R728 1-208-895-81 s RES, CHIP 2.2K (1005) RB202 1-234-381-21 s RES, NETWORK 100K (1005X4) R729 1-208-915-81 s RES, CHIP 15K (1005) R730 1-208-911-81 s RES, CHIP 10K (1005) RB501 1-234-371-21 s RES, NETWORK 47 (1005X4) A-13 SNC-DS10/DM110...