Sony SRG-300SE Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Digital Camera
  5. SRG-300SE
  6. Service manual

Sony SRG-300SE Service Manual

Hd color video camera
Hide thumbs Also See for SRG-300SE:
Table of Contents

Advertisement

Quick Links

HD COLOR VIDEO CAMERA
SRG-300SE
SRG-301SE
SERVICE MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony SRG-300SE

Summary of Contents for Sony SRG-300SE

  • Page 1 HD COLOR VIDEO CAMERA SRG-300SE SRG-301SE SERVICE MANUAL 1st Edition...
  • Page 2 Follow the instructions for the above port. fault should occur. WARNUNG Dieses Gerät hat keinen Netzschalter. Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen läßt. SRG-300SE/301SE...

  • Page 3: Table Of Contents

    Cabinet of the PAN/TILT Movable Portion) ...2-2 (E) 3-9. SDI Image Trouble ..........3-10 (E) 2-1-4. How to Access this Unit........2-7 (E) 3-10. Image Quality Trouble ..........3-11 (E) 2-1-5. How to Execute the CGI Command ....2-8 (E) 2-1-6. Resetting to Factory Setting ......2-8 (E) 1 (E) SRG-300SE/301SE...
  • Page 4 Notes on Repair Parts ............5-1 5-2. Exploded Views ............... 5-2 5-3. Packing Materials & Supplied Accessories ..... 5-8 6. Diagrams 6-1. Overall Block Diagram ........... 6-1 Overall ................6-1 6-2. Frame Wiring..............6-2 Frame Wiring..............6-2 2 (E) SRG-300SE/301SE...

  • Page 5: Manual Structure

    Manual Structure Purpose of this manual This manual is the Service Manual of the HD Color Video Camera SRG-300SE/301SE. This manual contains the service overview, procedure after replacement of part, troubleshooting, circuit description, spare parts, and block diagrams. The service of this unit is basically performed by the replacement of board.

  • Page 7: Service Overview

    . PSW2.6 x 6: 0.40 ?0.02 N.m (4.1 ?0.2 kgf.cm) . PSW3 x 8: 0.60 ?0.02 N.m (6.1 ?0.2 kgf.cm) When using the torque driver with the notation of cN.m, interpret it as follows. Example: 0.8 N.m = 80 cN.m 1-1 (E) SRG-300SE/301SE...

  • Page 8: Removing/Installing The Cabinet

    2. Insert the pin through the notch (A) of the base cabinet, then remove the hook (B) of the side cabinet (right) in the direction of the arrow C. Camera block Side cabinet (right) Base cabinet Hook (B) Notch (A) 1-2 (E) SRG-300SE/301SE...
  • Page 9 4. Insert the pin through the notch (D) of the base cabinet, then remove the hook (E) of the side cabinet (right) in the direction of the arrow C. Camera block Side cabinet (right) Notch (D) Hook (E) 1-3 (E) SRG-300SE/301SE...
  • Page 10 5. Remove the hook (F), then remove the side cabinet (right). 6. Remove the side cabinet (left) in the same procedure as steps 1 to 5. Side cabinet (left) Side cabinet (right) Hook (F) 7. To install, reverse the removal procedure. 1-4 (E) SRG-300SE/301SE...

  • Page 11: Camera Cabinet

    4. Remove the four hooks, then remove the camera cabinet (upper) and camera cabinet (lower). Left side view Right side view Lens Lens Screws Screws Camera cabinet (upper) Hook Camera block Hook Camera cabinet (lower) Hook Hook 5. To install, reverse the removal procedure. 1-5 (E) SRG-300SE/301SE...

  • Page 12: Removing/Installing The Main Parts

    Tape (A) BTP2.6 CN901 CN904 Ferrite core Fine-wire coaxial cable Fine-wire coaxial cable Fine-wire coaxial cable CN-3766 board Place the cable with the contact side facing upward. Fine-wire coaxial cable 5. To install, reverse the removal procedure. 1-6 (E) SRG-300SE/301SE...

  • Page 13: Fcb Assembly

    Align with the hole portion. Busteraid (0.5) FCB assembly Connector Fine-wire coaxial cable Front side BSW2 Fine-wire coaxial cable Tied portion Front cabinet Longer to the Shorter to the tied portion tied portion 7. To install, reverse the removal procedure. 1-7 (E) SRG-300SE/301SE...
  • Page 14 3. Remove the FCB assembly. (Refer to Section 1-4-2.) 4. Rotate the FCB holder in the direction of the arrow. 5. Remove the four screws, then remove the two center cabinets. Center cabinet FCB holder Center cabinet 6. To install, reverse the removal procedure. 1-8 (E) SRG-300SE/301SE...

  • Page 15: Board

    3. Disconnect the flexible flat cable from the connectors (CN201) on the AU-365 board. 4. Remove the three screws (PSW2.6 x 6), then lift up the AU-365 board. B2.6 B2.6 Bottom plate BTP3 CN201 Flexible flat cable AU-365 board Bottom side 5. To install, reverse the removal procedure. 1-9 (E) SRG-300SE/301SE...
  • Page 16 4. Disconnect the flexible flat cable from the connector and harness (CN801 and CN1202) on the SY- 437 board. 5. Remove the three screws, then lift up the SY-437 board. 6. Disconnect the harness from the connector (CN1701) on the SY-437 board. 1-10 (E) SRG-300SE/301SE...
  • Page 17 Cushion (ferrite) Ferrite core CN1202 Folded portion CN801 Front side CN101 Flexible flat cable Harness Ferrite core SY-437 board CN1701 Front side Harness Bottom side 7. To install, reverse the removal procedure. 1-11 (E) SRG-300SE/301SE...

  • Page 18: Board

    Replace the removed gasket with the new one. (Refer to Section 5.) Align with the outer shape of the board. Gasket LED-530 board Gasket Align the end of the LED-530 board copper foil. Harness CN9001 Bottom side 5. To install, reverse the removal procedure. 1-12 (E) SRG-300SE/301SE...

  • Page 19: Sw-1654 Board

    4. Remove the two screws, then remove the SW-1654 board. 5. Disconnect the harness from the connector (CN901) on the SW-1654 board. Harness Terminal reinforcing plate CN901 SW-1654 board Bottom side 6. To install, reverse the removal procedure. 1-13 (E) SRG-300SE/301SE...

  • Page 20: Tilt Chassis Assembly And Base Cabinet

    1-4-8. TILT Chassis Assembly and Base Cabinet 1. Remove the cabinet. (Refer to Section 1-3.) 2. Remove the SY-437 board. (Refer to Section 1-4-5.) 3. Remove the three screws, then remove the TILT chassis assembly. Bottom side TILT chassis assembly 1-14 (E) SRG-300SE/301SE...
  • Page 21 4. Remove the three screws, then remove the base cabi- net. PSW2.6 5. To install, reverse the removal procedure. Base cabinet 1-15 (E) SRG-300SE/301SE...

  • Page 22: Service Motor Assembly (Md-156)

    4. Remove the center cabinet. (Refer to Section 1-4-3.) 5. Remove the bottom plate. (Refer to steps 1 and 2 in Section 1-4-4.) 6. Remove the TILT chassis assembly. (Refer to steps 2 and 3 in Section 1-4-8.) 1-16 (E) SRG-300SE/301SE...
  • Page 23 Place the cable with the contact side facing front side. Fine-wire coaxial cable Harness Black paints CN401 CN101 CN501 Blue paints MD-156 board Place the cable with the Harness contact side facing front side. CN102 Fine-wire coaxial cable Fine-wire coaxial cable 1-17 (E) SRG-300SE/301SE...
  • Page 24 . When attaching the timing belt, push it against the guide of the TILT pulley. Guide FCB holder sub-assembly TILT pulley Timing belt TILT bearing holder (L) Timing belt Stepping motor TILT bearing holder (R) assembly (TILT) Screws Stepping motor assembly (TILT) 1-18 (E) SRG-300SE/301SE...
  • Page 25 13. Remove the two screws, then remove the stepping motor assembly (TILT). The combination of the stepping motor assembly (TILT) and stepping motor assembly (PAN) is predetermined. Be careful not to wrongly combine them. Stepping motor assembly (TILT) TILT chassis 1-19 (E) SRG-300SE/301SE...
  • Page 26 . Adjust the timing belt tension so that it is the same level as the tension before being removed. Harness guide (upper) Back side of harness guide (upper) Tape portion Fine-wire coaxial cable Hooks Stepping motor assembly (PAN) Screws Timing belt PAN shaft subassembly Harness guide (lower) PSW2.6 Fine-wire coaxial cable 1-20 (E) SRG-300SE/301SE...
  • Page 27 17. Remove the two screws, then remove the stepping motor assembly (PAN). Stepping motor assembly (PAN) The combination of the stepping motor assembly (TILT) and stepping motor assembly (PAN) is prede- termined. Be careful not to incorrectly combine them. TILT chassis PSW3 1-21 (E) SRG-300SE/301SE...
  • Page 28 . When attaching the MD-156 board, make sure that the extra length of PAN motor harness, TILT motor harness or fine-wire coaxial cable does not protrude from the TILT chassis. Hook PAN motor harness TILT chassis MD-156 board TILT motor harness Fine-wire coaxial cable 1-22 (E) SRG-300SE/301SE...
  • Page 29 TILT chassis through its hole, and put it through the two hooks. At that time, place the ROM board portion so that it is lower than the top of the boss. Boss Hole ROM board portion Hook Boss ROM board portion TILT chassis Hooks TILT chassis Harness Harness 1-23 (E) SRG-300SE/301SE...
  • Page 30 . When attaching the timing belt, rotate the PAN pulley five times in the direction of the arrow so that the timing belt comes in contact with the guide of the PAN pulley. PAN pulley Guide PAN pulley Timing belt Timing belt 1-24 (E) SRG-300SE/301SE...

  • Page 31: Fcb Holder

    TILT harness guide Fine-wire coaxial cable TILT shaft assembly Hooks Hooks Tape portion TILT harness guide BTP2.6 FCB holder TILT pulley BTP2.6 Ball bearing (L-1680) TILT bearing plate 13. To install, reverse the removal procedure. 1-25 (E) SRG-300SE/301SE...

  • Page 32: Pan Shaft Assembly

    . The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-26 (E) SRG-300SE/301SE...

  • Page 33: Procedure After Replacement Of Parts

    For the operating environment, refer to “Required system configuration” in the user’s guide. . SDI monitor Prepare the 3G-SDI compatible monitor. Prepare the 3G-SDI level A mapping. . LAN cable . BNC cable . 12 VDC power supply 2-1 (E) SRG-300SE/301SE...

  • Page 34: Installation Of Required Tool

    PAN/TILT movable portion) 1. Access the following URL and install the latest SNC toolbox on PC. Japanese site: http://www.sony.jp/brc/support/ English site: https://pro.sony.com/bbsc/ssr/cat-camerasptz/ You can also download the Application Guide that describes how to install and how to use the SNC toolbox from the above URL.
  • Page 35 1. Open “Start” → “Control Panel” →“Network and Internet” →“Network and Sharing Center”. The procedure and screen show the example of Windows 7. Local Area Connection 2. Click the local area connection. The Local Area Connection status screen is displayed. [Properties] button 2-3 (E) SRG-300SE/301SE...
  • Page 36 In “**”, set the value other than the IP address of this unit in the range from 1 to 254. (Set the address that does not conflict with other connected devices.) 6. Click the [OK] button. 7. Click the [OK] button on the property screen of the local area connection. 2-4 (E) SRG-300SE/301SE...
  • Page 37 [Search] button [Network] button Serial number Model information display Click this portion. 2. Click the model information display, and then click the [Network] button. The Device Account screen is displayed. “Administrator name” and “Administrator password” [OK] button 2-5 (E) SRG-300SE/301SE...
  • Page 38 When the setting is completed correctly, the Information screen is displayed. When an error is displayed, check the LAN cable connection between this unit and PC, and then perform the procedure from step 1 again. [OK] button 5. Click the [OK] button. 2-6 (E) SRG-300SE/301SE...

  • Page 39: How To Access This Unit

    2. Click the [Search] button. The model information of the connected camera is displayed. 3. Double-click the model information and open the homepage of this unit via Internet Explorer. The camera image appears after a period of time. 2-7 (E) SRG-300SE/301SE...

  • Page 40: How To Execute The Cgi Command

    NETWORK: stays lit in green. POWER: stays lit in green. 4. Click the [Search] button in the SNC toolbox, and check that this unit is set to DHCP. [Search] button Check that DHCP is displayed. 5. Exit the SNC toolbox. 2-8 (E) SRG-300SE/301SE...

  • Page 41: Board

    . Firmware version upgrade (Section 2-2-4) If the version upgrade is not performed, this unit may not operate normally. As for the SY-437 board, the parts to be replaced vary between SRG-300SE and SRG-301SE. Replace the parts required for each model. (Refer to Section 5.) 2-2-1.

  • Page 42: Confirmation Of Model Name/Mac Address And Writing Of Serial Number

    3. Turn on the power of each device and wait until the image is output on the SDI monitor. 4. Start the SNC toolbox and check that the model information is displayed. If it is not displayed, click the [Search] button. The screen shows an example of SRG-300SE. [Search] button Model information display 5.
  • Page 43 The MAC address should be the same as the MAC address label supplied with the SY-437 board. 3. Type the serial number of this unit and select the destination. Select the destination according to the model. SRG-300SE: WW SRG-301SE: CN Serial number...
  • Page 44 (The writing of serial number is completed.) Check that OK is displayed. If OK is not displayed, perform the procedure from step 1 again. 1. Exit G6 Serial_Inputter For Service. 2. Turn off the power of this unit. 2-12 (E) SRG-300SE/301SE...

  • Page 45: Firmware Version Upgrade

    3. Start the SNC toolbox and check that the serial number of this unit is displayed correctly. If it is not displayed correctly, click the [Search] button. [Search] button [Network] button Serial number Model information display Click this portion. 2-13 (E) SRG-300SE/301SE...
  • Page 46 Check the radio button. "IP address" and "Subnet mask" [OK] button 3. Check the “Use the following IP address” radio button, type IP address and Subnet mask as follows, then click the [OK] button. IP address: 192.168.0.100 Subnet mask: 255.255.255.0 2-14 (E) SRG-300SE/301SE...
  • Page 47 1 again. [OK] button 4. Click the [OK] button. [Upgrade] button 5. Click the [Upgrade] button. The Firmware Upgrade screen is displayed. [Browse] button Select the latest firmware. Remove the check of Setup data. [Start|Upgrading] button 2-15 (E) SRG-300SE/301SE...
  • Page 48 SNC toolbox are correct. Firmware version MAC address Serial number 1. Reset this unit to the factory setting according to Section 2-1-6. 2. Turn off the power of each device and disconnect the connections. 2-16 (E) SRG-300SE/301SE...

  • Page 49: Board

    . MIC (3.5φ mini jack) . 12 VDC power supply . Latest SNC toolbox Install the SNC toolbox according to Section 2-1-2 in advance. 2-17 (E) SRG-300SE/301SE...

  • Page 50: Confirmation Of Mic Input

    7. Update the browser and make a sound in front of the microphone. 8. Check that the sound is output from PC and that the audio level meter of this unit extends. Audio level meter of this unit 2-18 (E) SRG-300SE/301SE...

  • Page 51: Confirmation Of Line Input

    5. Check that the sound is output from PC and that the audio level meter of this unit extends. 1. Reset this unit to the factory setting according to Section 2-1-6. 2. Turn off the power of each device and disconnect the connections. 2-19 (E) SRG-300SE/301SE...

  • Page 52: Sw-1654 Board

    Set RM-IP10 setting to the RS-422 connection. 2. Turn on the power of this unit. 3. Wait until the image is output to the SDI monitor. 4. Check that this unit operates without any problem using RM-IP10. 2-20 (E) SRG-300SE/301SE...

  • Page 53: Operation Check Of Reset Switch

    Check that when the resetting is completed, each indicator is lit as follows and the image is output on the SDI monitor. NETWORK: stays lit in green. POWER: stays lit in green. 1. Turn off the power of each device and disconnect the connections. 2-21 (E) SRG-300SE/301SE...

  • Page 54: Board

    5. Check that when the resetting is completed, each indicator is lit as follows and the image is output on the SDI monitor. NETWORK: stays lit in green. POWER: stays lit in green. 1. Turn off the power of each device and disconnect the connections. 2-22 (E) SRG-300SE/301SE...

  • Page 55: Cn-3766 Board

    SDI monitor This unit 2. Turn on the power of this unit. 3. Check that the image is output on the SDI monitor after several minutes. 1. Turn off the power of each device and disconnect the connections. 2-23 (E) SRG-300SE/301SE...

  • Page 56: Service Motor Assembly (Md-156)

    The service motor assembly (MD-156) consists of the MD-156 board and two stepping motors. All of these parts need to be replaced at a time. Otherwise, problems such as unstable PAN/TILT opera- tion may occur. For details, refer to Section 1-4-9. 2-24 (E) SRG-300SE/301SE...

  • Page 57: Fcb Assembly

    . LAN cable . SDI monitor Prepare the 3G-SDI compatible monitor. Prepare the 3G-SDI level A mapping. . BNC cable . 12 VDC power supply . Latest SNC toolbox Install the SNC toolbox according to Section 2-1-2 in advance. 2-25 (E) SRG-300SE/301SE...

  • Page 58: Writing Of Fcb Adjustment Data

    Be sure to wait for at least 120 seconds and check that there is no abnormality in the image. 1. Reset this unit to the factory setting according to Section 2-1-6. 2. Turn off the power of each device and disconnect the connections. 2-26 (E) SRG-300SE/301SE...

  • Page 59: Troubleshooting

    SDI Image quality is abnormal. not reproduced normally. controller. connector. Go to “3-7. Audio Trouble”. Go to “3-8. Serial Connection Go to “3-9. SDI Image Trouble”. Go to “3-10. Image Quality Trouble”. Trouble”. 3-1 (E) SRG-300SE/301SE...

  • Page 60: Power Trouble

    Is a voltage of 3.3 V on the Replace the SY-437 board. SY-437 board output from (Refer to Section 1-4-5.) pin-1 of CN1202 normally? Replace the LED-530 board. (Refer to Section 1-4-6.) CN1202 F1801 SY-437 board (Side B) 3-2 (E) SRG-300SE/301SE...

  • Page 61: System Startup Trouble

    (S901/SW-1654 board) in the rear portion of this unit? FCB assembly: Refer to Section 1-4-2. CN-3766 board: Refer to Section 1-4-1. SY-437 board: Refer to Section 1-4-5. Return the camera setting to the state before resetting, and check again. 3-3 (E) SRG-300SE/301SE...

  • Page 62: Network Trouble

    (Refer to Section 2-1-6.) Set the IP address. Can the network be connected by accessing this unit from the PC browser? Perform the flow chart of Confirm the camera setting. “Confirmation of PC setting”. (Next page) 3-4 (E) SRG-300SE/301SE...
  • Page 63 There is a problem in the PC setting environment. Replace the SY-437 board. Is the symptom improved? (Refer to Section 1-4-5.) There is a problem in the firmware of this unit. Perform the firmware version upgrade. (Refer to Section 2-2-4.) 3-5 (E) SRG-300SE/301SE...

  • Page 64: Ip Image Trouble

    Replace the FCB assembly or There is a problem in the SY-437 board. firmware of this unit. Perform the firmware version upgrade. (Refer to Section 2-2-4.) FCB assembly: Refer to Section 1-4-2. SY-437 board: Refer to Section 1-4-5. 3-6 (E) SRG-300SE/301SE...

  • Page 65: Pan/Tilt Trouble

    CN-3766 board, If there is any abnormality, (Refer to Section 1-4-9.) and CN-3766 board and FCB replace it. (Refer to Section 5.) assembly connected correctly? Replace the service motor assembly (MD-156). (Refer to Section 1-4-9.) 3-7 (E) SRG-300SE/301SE...

  • Page 66: Audio Trouble

    Is FFC between the AU-365 Connect FFC correctly. board and SY-437 board If there is any abnormality, connected correctly? replace it. (Refer to Section 5.) FFC: Flexible flat cable Replace the AU-365 board. (Refer to Section 1-4-4.) 3-8 (E) SRG-300SE/301SE...

  • Page 67: Serial Connection Trouble

    Is the harness between the Connect the harness correctly. SY-437 board and SW-1654 If there is any abnormality, board connected correctly? replace it. (Refer to Section 5.) Replace the SW-1654 board. (Refer to Section 1-4-7.) 3-9 (E) SRG-300SE/301SE...

  • Page 68: Sdi Image Trouble

    Is the symptom improved by Replace the SY-437 board. disconnecting and connecting (Refer to Section 1-4-5.) the SDI cable? Replace the SDI cable. 3-10 (E) SRG-300SE/301SE...

  • Page 69: Image Quality Trouble

    Is the symptom improved by disconnecting and connecting the cable? Replace the FCB assembly or SY-437 board. Set the camera suitable for the FCB assembly: Refer to Section 1-4-2. operating environment. SY-437 board: Refer to Section 1-4-5. 3-11 (E) SRG-300SE/301SE...

  • Page 71: Sw-1654 Board

    The MD-156 board is connected with a pan/tilt motor and ROM-33 board using each 6-pin cable so as to control the motor. It is also connected with the SY-437 board using a 30-pin fine-wire coaxial cable. Similarly, it is connected with the CN-3766 board using a 30-pin fine-wire coaxial cable. 4-1 (E) SRG-300SE/301SE...

  • Page 72: Md-156 Board

    The ROM-33 board is connected with the microcomputer on an MD-156 board using a serial communica- tion line and used to confirm the ID numbers of a pan motor and tilt motor. 4-2 (E) SRG-300SE/301SE...

  • Page 73: Spare Parts

    Therefore, specified parts should be used in the case of な部品です。したがって，交換する時は必ず指定 replacement. の部品を使ってください。 2. Standardization of Parts 2.  部品の共通化 Some repair parts supplied by Sony differ from those   ソニーから供給する補修用部品は，セットに使われて used for the unit. These are because of parts common- いるものと異なることがあります。 ality and improvement.

  • Page 74: Exploded Views

    Cabinet Block 5-2. Exploded Views SRG-300SE/301SE...
  • Page 75 4-472-126-02 s CABINET, SIDE (For Black Model) 4-472-126-11 s CABINET, SIDE (For White Model) 4-472-128-01 s CABINET, CAMERA (For Black Model) 4-472-128-11 s CABINET, CAMERA (For White Model) 4-472-129-01 s CABINET, FRONT 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S SRG-300SE/301SE...
  • Page 76 Board Block B2.6 B2.6 BTP3 SY-437 Board (B side) F1801 SRG-300SE/301SE...
  • Page 77 A-2054-408-A s MOUNTED CIRCUIT BOARD, AU-365 A-2054-409-A s MOUNTED CIRCUIT BOARD, SW-1654 A-2054-410-A s MOUNTED CIRCUIT BOARD, LED-530 A-2068-080-A s MOUNTED CIRCUIT BOARD, SY-437 (RP) (For SRG-300SE) A-2068-081-A s MOUNTED CIRCUIT BOARD, SY-437 (RP) (For SRG-301SE) X-2590-522-1 s WINDOW ASSY,RAY CATCHER(WHITE)
  • Page 78 7-621-759-45 s +PSW, 2.6X6 4-472-127-01 s CABINET, CENTER (For Black Model) 7-628-000-05 s +PSW 2X6 4-472-127-11 s CABINET, CENTER (For White Model) 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S 4-472-120-02 s HOLDER, FCB 4-472-121-01 s PULLEY, TILT 1-481-788-11 s CORE, FERRITE SRG-300SE/301SE...
  • Page 79 A-2065-532-A s SHAFT ASSY, PAN A-2068-079-A s MOTOR ASSY(MD-156), SERVICE 4-382-854-01 s SCREW (M3X8), P, SW (+) 4-471-365-02 s PULLEY, PAN 4-471-368-01 s BELT, TIMING 1-969-827-11 s HARNESS (COAXIAL 30P/MD-IF) 7-621-759-45 s +PSW, 2.6X6 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S SRG-300SE/301SE...

  • Page 80: Packing Materials & Supplied Accessories

    Accessories ---------------------------------------- PACKING MATERIALS & SUPPLIED ACCESSORIES ---------------------------------------- *1:[For SRG-300SE(J)/SRG-300SE WC(J)] *2:[For SRG-301SE(CN)/SRG-301SE WC(CN)] *3:[For SRG-300SE/SRG-301SE] *4:[FOr SRG-300SE WC/SRG-301SE WC] Ref. No. or Q’ty Part No. SP Description 1-480-216-17 s ADAPTOR, AC 1-843-035-12 s PLUG, CONNECTOR 9P 1pc *1 1-846-099-41 s CORD SET, POWER-SUPPLY 125V 7A (For J) 1pc *2 1-846-103-52 s CORD SET, POWER-SUPPLY 250V 2.5A (For CN)

  • Page 81: Diagrams

    +2.5V_SYS DC/DC +1.5V_DMP_DDR DC/DC Self Reset WDTout +1.8V_SYS DC/DC MDIO Reset XRSTi MDIO Pulse RST# +1.2V_SYS DC/DC Voltage Det Trans DC/DC +3.3V_SYS IRQ_Exp +3.3V IRQ_PHY INTR IRQ_PHY PHY_RST# INT_VD +5V_SYS DC/DC 25MHz CamBlockOn DSR_OUT xPAL/NT XDSR_OUT Power +12V_CAM Overall SRG-300SE/301SE...

  • Page 82: Frame Wiring

    RTC_CAP RXD_IN_+ EXT_FRESET EXT_FRESET TXD_IN_- EXT_27M EXT_27M SW_FactRST SW_FactRST TXD_IN_+ SW_BaudRate SW_BaudRate S901 CN801 ROM-33 ROM-33 TILT Motor PAN Motor FLEXIBLE FLAT CABLE J201 MIC_L_IN MIC_R_IN (PLUG IN POWER) MIC_RTN J203 CN201 L_IN LINE IN L_GND AU-365 Frame Wiring SRG-300SE/301SE...
  • Page 84 SRG-300SE (J) SRG-300SE (SY) Printed in Japan Sony Corporation SRG-301SE (CN) J, E 2014. 11 32 9-878-620-01 ©2014...

This manual is also suitable for:

Srg-301se

Table of Contents