Table of Contents
Advertisement
PM4H-A/S/M
OPERATION MODE
PM4H-A
Operation mode
Turn the operation selector to
Power is applied continuously. When a start signal is applied, the
time cycle begins. The output contacts change state after the time
delay is completed. The contacts will return to their normal state
when a reset signal is applied or power is removed.
Pulse
(Note: When a stop signal is applied during timing operation, the time
ON-delay
cycle stops. When a stop signal is removed, the time cycle begins.)
ON
Turn the operation selector to
Power is applied continuously. When a start signal is applied, the
time cycle begins but the output contacts remain in their normal state.
When the time delay is completed, the output contacts change state
and next time cycle begins. When this time delay is completed, the
Pulse
output contacts return to their normal state. This cycle will repeat until
Flicker
a reset signal is applied or power is removed.
FL
(Note: When a stop signal is applied during timing operation, the time
cycle stops. When a stop signal is removed, the time cycle begins.)
Turn the operation selector to
Power is applied continuously. When a start signal is applied, the out-
put contacts change state immediately and time cycle begins. When
the time delay is completed, the output contacts change state and
next time cycle begins. When the time delay is completed, the output
Pulse
contacts return to the normal state.
ON-flicker
This cycle will repeat until a reset signal is applied or power is
FO
removed.
(Note: When a stop signal is applied during timing operation, the time
cycle stops. When a stop signal is removed, the time cycle begins.)
Turn the operation selector to
Power is applied continuously. When a start signal is applied, the out-
put contacts change state immediately and time cycle begins. The
output contacts change state after the timing cycle is completed.
When the start signal is removed, the output contacts change state
Differential
and time cycle starts again. If operation signal is turned ON or OFF
ON/OFF-delay (1)
during timing operation, time cycle restart at that point.
OF1
The output contacts will return to their normal state when a reset sig-
nal is applied or power is removed.
(Note: When a stop signals is applied during timing operation, the time
cycle stops. When a stop signal is removed, the time cycle begins.)
Turn the operation selector to
Power is applied continuously. When a start signal is applied, the out-
put contacts change state immediately. When the start signal is
removed the time cycle begins. The output contacts will return to their
normal state when the time delay is completed.
Signal
Reset will occur when a reset signal is applied or power is removed.
OFF-delay
(Note: When a stop signal is applied during timing operation, the time
SF
cycle stops. When a stop signal is removed, the time cycle begins.)
Note: Keep 0.1s or more for power off time.
Keep 0.05s or more for signal, stop, reset input time.
The new settings
are valid after power OFF
Operation
.
ON
.
FL
.
FO
.
OF1
.
SF
02/2003
LED lighting
ON
T: Setting time t
Time chart
ON
Power supply
ON
OFF
Operation signal
–
Reset
–
Stop
–
T
ON
Time out (N.O. contact)
OP. LED
POWER LED
Note:
LED lighting or No LED lighting
ON
Power supply
ON
OFF
Operation signal
–
Reset
–
Stop
–
T
ON
Time out (N.O. contact)
OP. LED
POWER LED
Note:
LED lighting or No LED lighting
ON
Power supply
ON
OFF
Operation signal
–
Reset
–
Stop
–
T
ON
Time out (N.O. contact)
OP. LED
POWER LED
ON
Power supply
ON
Operation signal
–
Reset
–
Stop
–
T
ON
Time out (N.O. contact)
OP. LED
POWER LED
Note:
LED lighting or No LED lighting
ON
Power supply
ON
OFF
Operation signal
–
Reset
–
Stop
–
T
ON
Time out (N.O. contact)
OP. LED
POWER LED
Note:
LED lighting or No LED lighting
LED flickering
, t
, t
, t
<T t
+t
=T
1
2
a
b
1
2
OFF
ON
ON
OFF
ON
OFF
ON
OFF
t
t
1
2
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
T
t
t
t
t
a
1
2
b
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
T
t
t
t
T
t
a
1
2
b
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
t
t
t
t
1
2
a
b
ON
ON
OFF
OFF
OFF
Restart
OFF
ON
OFF
ON
OFF
ON
OFF
t
t
a
b
OFF
15
- Quick Links:
- Wiring Diagrams
- Operation Mode
- Time-Range
- Operation
Hide quick links:
Advertisement
Table of Contents
