Power Indicator; Level Meter - Yamaha MG124C Owner's Manual
Yamaha mixing console owner's manual
Hide thumbs
Also See for MG124C:
- Manuel du propriétaire (24 pages) ,
- Owner's manual (24 pages) ,
- Owner's manual (24 pages)
Table of Contents
Advertisement
8
PHONES Jack
Connect a pair of headphones to this stereo phone jack. The
PHONES jack outputs the same signal as the MONITOR
OUT jacks.
9
PHANTOM +48 V Switch
This switch toggles phantom power on and off. When the switch
is on the mixer supplies +48V phantom power to all channels
that have XLR mic input jacks (CHs 1–4, 5/6, 7/8).
Turn this switch on when using one or more phantom-pow-
ered condenser microphones.
When this switch is on the mixer supplies DC +48 V
NOTE
power to pins 2 and 3 of all XLR-type MIC INPUT
jacks.
Be sure to leave this switch off (
•
not need phantom power.
When tuning the switch on (
•
CAUTION
only condenser mics are connected to the
XLR input jacks (CHs: 1 to 7/8). Devices
other than condenser mics may be damaged if
connected to the phantom power supply. Note,
however, that the switch may be left on when
connecting to balanced dynamic microphones.
To avoid damage to speakers, be sure to turn
•
off amplifiers (or powered speakers) before
turning this switch on or off. We also recom-
mend that you turn all output controls (STE-
REO OUT Master Fader, GROUP 1-2 Fader,
etc.) to their minimum settings before operat-
ing the switch to avoid the risk of loud noises
that could cause hearing loss or device damage.
0 RETURN
• AUX (AUX1) Control
Adjusts the level at which the L/R signal received at the
RETURN jacks (L (MONO) and R) is sent to the AUX
(AUX2) bus.
• STEREO Control
Adjusts the level at which the signal received at the
RETURN jacks (L (MONO) and R) is sent to the STEREO
L/R buses.
If you supply a signal to the RETURN L (MONO)
NOTE
jack only, the mixer sends the same signal to both the
L and R Stereo buses.
A Master SEND
• Master AUX (AUX1) Control
Adjusts the signal level sent to the AUX (AUX1) SEND jack.
• Master EFFECT (AUX2) Control
Adjusts the level of the signal sent to the EFFECT (AUX2)
bus.
If you are using the MG124CX, the Master EFFECT
NOTE
control does not affect the level of the signal sent
from the EFFECT bus to the internal digital effect
processor.
B POWER Indicator
This indicator lights when the mixer's power is ON.
C Level Meter
This LED meter displays the level of the signal selected by
D
the MONITOR switch
switch. The "0" segment corresponds to the nominal output
level. The PEAK segment lights red when the output reaches
the clipping level.
) if you do
), be sure that
E
, 2TR IN switch
and PFL
D MONITOR/PHONES
• MONITOR Switch
If this switch is set to GROUP (
nals are sent to the MONITOR OUT jacks, the PHONES
jack, and the level meter. If it is set to STEREO (
STEREO L/R bus signals are sent to these jacks and the level
meter.
• MONITOR Control
Controls the level of the signal output to the PHONES jack
and the MONITOR OUT jacks.
E 2TR IN
• 2TR IN Switch
If this switch is set to TO MONITOR (
via the 2TR IN jacks are sent to the MONITOR OUT jacks,
the PHONES jack, and the level meter. If it is set to TO STE-
REO (
), the signals are sent to the STEREO L/R buses.
• 2TR IN control
Adjusts the level of the signal sent from the 2TR IN jacks to
the STEREO L/R buses.
The following illustration shows how the switch settings cor-
respond to the signal selection.
Switches
MONITOR/
PFL
2TR IN
PHONES
ON
—
—
TO STEREO
STEREO
TO MONITOR STEREO + 2TR IN
OFF
TO STEREO
GROUP
TO MONITOR GROUP (+ 2TR IN)
*
: When overdubbing, you can adjust the levels of the
monitor playback signal and the signal being recorded separately.
MONITOR MIX Signal Flow
2TR IN Control
2TR IN
Playback
signal
STEREO
buses
Recording
signal
STEREO OUT Master Fader
If the input channel PFL switch is on (
NOTE
the PFL output from that channel is sent to the C-R
OUT jacks, PHONES jacks, and level meter.
F GROUP 1-2 Fader
Adjusts the signal level sent to the GROUP OUT jacks.
G ST Switch
If this switch is on (
), the signals are sent to the STEREO
L/R buses via the GROUP 1-2 fader
goes to Stereo L and the Group 2 signal goes to Stereo R.
H STEREO OUT Master Fader
Adjusts the signal level sent to the STEREO OUT jacks.
MG124CX/MG124C Owner's Manual
Reference
Front & Rear Panels
), the Group 1/2 bus sig-
), the
), the signals input
Signals output via the
MONITOR/PHONES
jacks
PFL
STEREO (+ 2TR IN)
*
GROUP
MONITOR/PHONES Controls
MONITOR/
PHONES
jacks
REC OUT
), then only
F
. The Group 1 signal
15
Hide quick links:
Advertisement
Table of Contents
