Advertisement
Quick Links
This document describes how to install a diskette drive.
Kit Contents
This product is shipped with the necessary supplies for installing a diskette drive in various workstation
models, so you might not use all of the cables, bezels, or screws.
■ Diskette drive
■ Cables
❏ HP Workstation xw8200 and HP Workstation xw6200—round cable
❏ HP Workstation xw4200 and HP Workstation xw4100—flat cable
■ Three bezels (one for each workstation)
❏ HP Workstation xw8200—5.25-inch bezel
❏ HP Workstation xw6200—3.5-inch bezel (thinner than the xw4200 and xw4100)
❏ HP Workstation xw4200 and HP Workstation xw4100—3.5-inch bezel (thicker than the xw6200)
■ Screws (xw8200, xw4200, and xw4100 only)
■ Bracket (xw8200 only)
Gather your Supplies
■ Option kit
■ Printed copies of relevant workstation documentation, which can be found at
http://www.hp.com/support/workstation_manuals
Installing a Diskette Drive
For product-specific information, refer to the Service and Technical Reference Guide for your HP
Workstation at http://www.hp.com/support/workstation_manuals.
1. Disconnect power from the system, remove the access panel, the front bezel, the necessary bezel
blank, and the EMI filler blank, if applicable.
Diskette Drive Installation
HP Workstation xw Series
Advertisement
Related Manuals for HP Workstation xw Series
Summary of Contents for HP Workstation xw Series
- Page 1 ■ Printed copies of relevant workstation documentation, which can be found at http://www.hp.com/support/workstation_manuals Installing a Diskette Drive For product-specific information, refer to the Service and Technical Reference Guide for your HP Workstation at http://www.hp.com/support/workstation_manuals. 1. Disconnect power from the system, remove the access panel, the front bezel, the necessary bezel...
- Page 2 NOTE: This step only applies to HP Workstation xw8200. 3. Slide the drive into the bay. For the HP Workstation xw4200 and xw4100, you must add four screws to secure the diskette drive to the chassis. 4. Connect a data cable from the system board to the diskette drive and connect the power cable from the power supply to the diskette drive.
- Page 3 Diskette Drive Installation 5. Route the diskette drive data cable between the system board and the hard drive cage. Your cable might look different than the one shown. CAUTION: The cable must stay between the system board and the hard drive cage. It might be Ä...
- Page 4 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. 365444-001...
- Page 5 ❏ HP Workstation xw8200 用 —5.25 イ ンチ ベゼル ❏ HP Workstation xw6200 用 —3.5 イ ンチ ベゼル （xw4200 お よ び xw4100 用 よ り 薄い） ❏ HP Workstation xw4200 お よ び HP Workstation xw4100 用 —3.5 イ ンチ ベゼル（xw6200 用 よ...
- Page 6 注記 : こ の手順は、 HP Workstation xw8200 にのみ必要です。 3. フ ロ ッ ピー デ ィ ス ク ド ラ イ ブ をベ イ に ス ラ イ ド し て挿入 し ます。 HP Workstation xw4200 お よ び xw4100 の場合は、 さ ら に 4 箇所ネジ止め し 、 フ ロ ッ ピー デ ィ ス ク ド ラ イ ブ を シ ャ ー...
- Page 7 ロ ッ ピー デ ィ ス ク ド ラ イ ブ を電源ケーブルで接続 し ます。 お使いのシ ス テ ムに よ っ ては、 シ ス テ ム ボー ド の コ ネ ク タ の位置や、 使用す る 電源ケーブルが異な り ます。 お使いの HP ワ...
- Page 8 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. 365444-001...