Table of Contents
Advertisement
Quick Links
For Apartment Building HA D Series
Base Unit Number
VGDT18143W
•
VGDT18543W
•
VGDT18643W
VGDT18723W
VGDT18223W
VGDT18323W
•
•
Call Sub-base Unit with Monitor Number
VGD13111W
Receiving a Call
(For Base Unit/Call Sub-base Unit with Monitor)
When receiving a call from the main entrance, unit entrance, or building manager room with video
capability, call tone will ring, the screen will display the caller's image, and the TALK button and call origin
display will flash. (When the call is from the building manager room, the call origin display will appear.)
If the call from the unit entrance or building manager room has no video capability and the call is from another unit, the screen
•
will appear in blue.
1
Press the TALK button to answer
A "beep" sound is played, and the TALK button
and the call origin display appears.
2
Talk into the microphone
The conversation will automatically end in
•
approximately 1 minute. (When the call is from the
building manager room (without video capability),
it will end in approximately 4 minutes.)
When the volume is too low (
Page 31)
twice → Volume will be adjusted each
Touch
Page 1
time you touch
.
Volume
Unlocking the Main Entrance (illuminated UNLOCK button)
Press the flashing in green
UNLOCK button while talking
with the Main
entrance
The main entrance will be
•
unlocked. After approximately
Flashes when the door can
5 seconds, the screen will
be unlocked (illuminated
automatically turn off, and the
UNLOCK button)
conversation will end.
Extension Call
(For Base Unit/Call Sub-base Unit with Monitor)
1
Press the MENU button
2
Touch
3
Touch
For more information to operate the call sub-base unit, see the left side of the verso.
8A9 J61 00002
S0316-11016AB
S i mp l e G u i d e
•
VGDT18145W
•
VGDT18645W
•
VGDT18743W
•
VGDT18243W
VGDB18143W
VGDB18543W
VGDB18643W
VGDB18145W
•
•
•
•
Call Sub-base Unit Number
VGD13113W
3
Press the TALK button to end
A "beep" sound plays, the TALK button and
•
screen turn off and the call ends.
If you do not press the TALK button to end
Note
the call, the room sound will be transmitted
to the caller.
Call origin
display
Page 1
23
Page
UNLOCK
button
TALK
button
●
For base unit
Call tone "beep" sounds
After calling, you can talk for approximately 10
•
seconds even without pressing the TALK
button. (The TALK button lights up in red.)
After approximately 10 seconds, the status
•
changes to the waiting state of answering (the
call is ended once) and the TALK button goes off.
5
Talk once the call destination answers
It is enabled to talk with the base unit or
•
sub-base unit which replied.
6
Press the TALK button to end
◎ T his document is a digest of the attached operation manual (CD-ROM). Refer to the attached
operation manual (CD-ROM) for details. (Example: The notation
page 22 of the attached operation manual (CD-ROM).)
•
VGDT18343W
•
◎ I nformation on the condominium HA system is available. (As of September, 2016)
VGDB18645W
•
http://www2.panasonic.biz/es/densetsu/ha/mansion_ha/index.html
Useful Functions for Answering
22
Page
Yuttari Talk
(For Base Unit)
The speaking speed of the caller becomes slower and it
makes easier for you to hear the caller.
twice → Touch
Touch
Page 1
• The display will change from
• To switch back to the original speed, touch
• You can set
from the beginning of the call in accordance
Yuttari ON
with the configured settings. (
MENU
Excuse Function
button
This function helps to end the call quickly by playing a
sound of a telephone or a crying baby.
Touch
Excuse
Continuation Function
You can extend answering time every 1 minute.
OFF
Answering time can be extended up to 3 minute. (When the
button
call from the building manager room (without video
capability), you can extend answering time up to 10
minutes)
Touch
Cont
Microphone
will start to flash after approximately 50 seconds you start
•
Cont
answering. (When the call is from the building manager room
(without video capability),
44
Page
3 minutes and 50 seconds.)
Pretending to Be Out Function
You can use the Pretending to Be Out function to play the
away from home message.
Touch
when receiving a call
Message
• You can choose the away from home message or set the
pretend to be out display on or off in accordance with the
configured settings. (
Security Function
For about the security function, refer to
Page 22, means to refer to
32
Page
Yuttari OFF
to
.
Yuttari OFF
Yuttari ON
.
Yuttari ON
Page 106)
33
Page
33
Page
will start to flash in approximately
Cont
34
Page
Pages 103 to 105)
page 166 to 170 and 186 to 201.
Page 1
Yuttari ON
Yuttari OFF
Excuse
Cont
Message
Advertisement
Table of Contents
Related Manuals for Panasonic Windea VGDT18143W
Summary of Contents for Panasonic Windea VGDT18143W
- Page 1 VGDB18145W VGDB18645W • • • • • • • http://www2.panasonic.biz/es/densetsu/ha/mansion_ha/index.html Call Sub-base Unit with Monitor Number VGD13111W Call Sub-base Unit Number VGD13113W Receiving a Call Useful Functions for Answering (For Base Unit/Call Sub-base Unit with Monitor) Page When receiving a call from the main entrance, unit entrance, or building manager room with video capability, call tone will ring, the screen will display the caller’s image, and the TALK button and call origin...
- Page 2 Receiving a Call When the Area around the MENU Button Flashes in Blue (For Call Sub-base Unit) Page Page 58 to 60 • When the area around the MENU button flashes in blue, there are notifications of visitors etc. during When receiving a call from the main entrance, unit entrance, or building manager room, call tone will ring.
- Page 3 (Recessed Type) (White) VGD13113W Item number Thank you very much for purchasing the Panasonic product. Panasonic Corporation System Components Business Unit ● Read the operation manual carefully for correct and safe use. Be sure to read "Safety Precautions" (page 8) before use.
- Page 4 Skip to the Content You Want to Know Since the settings of the base unit differ for each condominium building, consult with the management company or the company that installed the system regarding the setting. If the caller talks too fast Continuation How to extend talk time? Yuttari Talk...
-
Page 5: Table Of Contents
Contents Checking the Integral Value 78 to 79 INTRODUCTION Checking the Time Zone Rate for the Electricity Checking the Eco Record Safety Precautions Checking the Eco Saving Level Cautions 9 to 12 Using the Eco-report Creation Tool Notes to All Residents Living Mode Switching 84 to 88 Part Names and Functions... - Page 6 Contents OPERATIONS AND MEASURES WHEN ALARM GOES OFF OTHER Connected System Components in Apartment Units (Example) 154 to 155 Lobby Phones 209 to 219 In the Event of Fire or Disconnection 156 to 160 Expire Date of the Gas Alarm In the Event of a Gas Leak or Disconnection 161 to 163 Troubleshooting...
-
Page 7: Safety Precautions
This product has a function to notify the alarm that was detected by the gas alarm and detector, but it will not prevent gas leak, carbon monoxide poisoning, or fire. Please note that Panasonic is ■ The following symbols indicate the type of precautions that must be not liable for any damage caused by gas leak, incomplete combustion, fire, etc. - Page 8 Ventilate after the use, and make the Measurement Act. Please note that Panasonic is not liable when this product is used as a sure to remove the plastic bag.
-
Page 9: Notes To All Residents
Emergency button, and the Call button. PC, etc. Please note that Panasonic is not liable for any damage of damaged or lost data. ● ... -
Page 10: Part Names And Functions
Part Names and Functions Security Intercom Model 1M Base Unit ● (Recessed Type) (White) This is not displayed in normal conditions. Note ● Installation setting on the base unit is necessary to display the Unlock indicator and the Lock OPEN indicator. - Page 11 Part Names and Functions Security Intercom Model 3M Call Sub-base Unit with Monitor Security Intercom Model 3M Call Sub-base Unit (Recessed Type) (White) (Recessed Type) (White) ● Unit expansion adapter (sold separately) on the base unit is Note Unit expansion adapter (sold separately) on the base unit is Note required to use.
- Page 12 Part Names and Functions Inserting and the Removing microSD Memory Card (For Base Unit) Difference of the Screen Display on the Base Unit and the Call Sub-base Unit with Monitor ● Insert the microSD memory card during the waiting state (nothing is displayed on the screen). Note ● ...
-
Page 13: Top Menu
Top Menu (For base unit/call sub-base unit with monitor) The Top Menu screen to perform various operations and settings is displayed when the ● Note The content and size of the buttons displayed vary depending on the condominium MENU button ( pages 15 to 16) is pressed while the screen is blank. -
Page 14: Unlocking The Main Entrance
Receiving a Call (For base unit/call sub-base unit with monitor) Unlocking the Main Entrance Main screen Sub-screen* (illuminated UNLOCK button) Receiving a call from the main entrance, unit entrance, building Press the UNLOCK button flashing in green 復旧/警報音停止 manager room, and other units RESET/ STOP ALARM while talking with the main entrance ●... -
Page 15: Lobby Phone Video
Receiving a Call (For base unit/call sub-base unit with monitor) ● If operated while receiving a call Lobby Phone Video Switching between the main screen and the sub-screen Video appears on the sub-screen when receiving a call from the main entrance. Touch the sub-screen Touch Note... -
Page 16: Recording Video And Audio When At Home
Receiving a Call (For base unit/call sub-base unit with monitor) Recording Video and Audio When at Home Recording Video and Audio Using the Not-home Setting (For Base Unit) (For Base Unit) Video is automatically recorded when receiving a call from the main entrance, unit entrance (door Video and audio of visitors and important matters from the building manager room can be recorded phone with camera), and building manager room (with video capability) when the Not-home setting when the Not-home setting is set to "Not Home: On (Immediately)"... -
Page 17: Adjusting The Video
● Only microSD memory cards from 4GB to 32GB are compatible. Touch Adjust 1 We recommend using memory cards manufactured by Panasonic. ● You can correct the video up to 3 levels with ● Only audio can be recorded for visitor information when using the base unit with sound each press. -
Page 18: Automatic Zoom Function
Receiving a Call (For base unit/call sub-base unit with monitor) Automatic Zoom Function If the Video Is Dark and Difficult to See (For Unit entrance only) In addition to the typical zoom function when receiving a call from the main entrance (lobby Touch phone) or during a call, a function to recognize and zoom into the visitor's face automatically is Light OFF... -
Page 19: Useful Functions
Receiving a Call (For base unit/call sub-base unit with monitor) Useful Functions Useful Functions Convenient Convenient Excuse Function Yuttari Talk (for the base unit) Use this function when you want to end a call quickly. It helps to end the call quickly by Use this function when you want to listen slowly to the visitor during a call. -
Page 20: Receiving A Call (For Call Sub-Base Unit)
Receiving a Call Receiving a Call (For base unit/call sub-base unit with monitor) (For call sub-base unit) Useful Functions Receiving a call from the main entrance, unit entrance, building MANAGER indicator manager room, or other units Convenient LOBBY indicator ● The ringtone plays, and the TALK Pretending to Be Out Function button flashes. -
Page 21: Unlocking The Unit Entrance
Configure the Not-home Setting Receiving a Call (For call sub-base unit) (For base unit) Use this function when you are out or away from home. If the Not-home function is set and the Unlocking the Unit Entrance (illuminated UNLOCK button) base unit receives a call, the call sound rings, then the Not-home message ( page 103) plays, and the visitor's voice is automatically recorded. -
Page 22: Receiving A Call While Talking
Receiving a Call While Talking Configure the Not-home Setting (For base unit) ● Call source appears on the sub-screen, which changes to a blue screen. (The sub-screen turns Deactivating the Not-home Setting Note blue even when called from the lobby phone with camera or door phone with camera.) ●... -
Page 23: Calling The Unit Entrance
Calling the Unit Entrance Receiving a Call While Talking For Base Unit/ Call Sub-base Unit with Monitor Press the TALK Button Again 通話 TALK ● A call can be made to a new call destination. Press the MENU button in ●... -
Page 24: Calling The Building Manager Room
Calling the Building Manager Room Calling the Unit Entrance (For base unit/call sub-base unit with monitor) For the condominium that supports the manager call function (calling the building manager For Call Sub-base Unit room from a unit), it is enabled to call the building manager room. Note The call sub-base unit is not compatible with calling the building manager room. -
Page 25: Extension Call (Call With Base Unit/Call Sub-Base Unit)
Extension Call (Call with base unit/call sub-base unit) Calling an Extension Calling an Extension For Base Unit/Call Sub-base Unit with Monitor For Call Sub-base Unit Open the Calling screen Press the EXTENSION button Page 41) ● Calls the base unit or another VGD13113W VGD13113W 非常... -
Page 26: Calling Another Unit
Calling another Unit Extension Call (Call with base unit/ sub-base unit) (For base unit) For a condominium that supports the unit call function (calling another unit from a unit), it is Receiving a Call enabled to call another unit. ● Other units cannot be called when "Reject Calls"... -
Page 27: Calling The Elevator
Calling the Elevator Locking/Unlocking the Unit Entrance (For base unit/call sub-base unit with monitor) (For base unit/call sub-base unit with monitor) If the elevator system is linked to the condominium HA system, you can call the elevator. (If you If the electronic lock system linked to the condominium HA system is installed in the unit that do not know the operating status, check with the management company, building manager you are staying in, the unit entrance can be locked and unlocked. -
Page 28: When A Delivery Article Arrives In The Delivery Box
When a Delivery Article Arrives in the Delivery Box Locking/Unlocking the Unit Entrance (For base unit/call sub-base unit with monitor) (For base unit/call sub-base unit with monitor) If a delivery box system linked with the condominium HA system is installed, you will be Unlocking the unit entrance informed of the arrival of any delivery. -
Page 29: When There Is A Message (Contact) From The Building Manager Room
When There Is a Message (Contact) from the Building Manager Room When There Is a Voice Mail from the Building Manager Room (For base unit/call sub-base unit with monitor) (For base unit/call sub-base unit with monitor) When there is a message (contact) from the building manager room, a manager's message appears, If there is a voice mail from the building manager room, it can be played back in the base unit. -
Page 30: When There Is An Announcement From The Building Manager Room
When There Is an Announcement from the Building Manager Room (For base unit/call sub-base unit with monitor) When there is an announcement (general announcement or emergency announcement), Touch the displayed you can check the announcement by using the base unit or call sub-base unit. 復旧/警報音停止... -
Page 31: When There Is A Notification From The Ev Charging System
When There Is a Notification from the EV Charging System (For base unit/call sub-base unit with monitor) If the installed EV charging system is linked to the condominium HA system, an EV charging When Checking for Available Sockets (for base unit) notification will be sent. -
Page 32: When The Area Around The Menu Button Flashes In Blue
When the Area around the MENU Button Flashes in Blue (For base unit/call sub-base unit with monitor) When is touched When there is a notification of a delivery or a visitor in your absence, the area around the MENU button flashes in blue. ●... -
Page 33: About Messages
About Messages When the Area around the MENU Button Flashes in Blue (For base unit/call sub-base unit with monitor) (For base unit) When is touched Messages can be recorded and played back in the base unit. Use it for messages between family members. - Page 34 About Messages (For base unit) Playing Back a Message Touch when the audio recording ends Note To check a message when the light in the area around the MENU button goes off, perform ● The Message screen appears, and the operation in pages 61 to 62, and touch in Step the date and time of the audio recording appear.
- Page 35 When You Want to Know the Scene around the Unit Entrance When You Want to Know the Scene of the Common Area (For base unit, call sub-base unit with monitor) (For base unit with browser function) If a door phone with camera is installed in the unit entrance, you can check the image around If the installed public camera (monitoring camera etc.) is linked to the condominium HA system, the entrance.
-
Page 36: About The Browser Function
About the Browser Function (For base unit with browser function) は じ め If information and other services are provided by the condominium management company etc., Checking the Description of the News に and you are using a base unit with the browser function, the news and living memo functions are available. - Page 37 About the Browser Function (For base unit with browser function) Checking the Description of the Lifestyle A detailed description of the selected news appears Open the Information screen ・ ● If 1/2 appears, touch to check the details as other information is included. Page 67) ●...
-
Page 38: When Checking The Power Consumption Volume
When Checking the Power Consumption Volume About the Browser Function (For base unit with browser function) (For base unit) If you are using a residential distribution panel equipped with an over-currency alarm (data output type) (5 level display type), you can check the the power consumption volume. (If you do After Moving In/Before Moving Out not know the equipment installed, check with the management company, building manager room, etc.) -
Page 39: About The Energy Saving Monitor
About the Energy Saving Monitor Viewing the Energy Saving Monitor Screen (For base unit) (For base unit) You can check the electricity consumption status and energy saving achievement level etc. You can check the current electricity consumption status at a single glance. There are 3 types of screens available - bubble display, simple display, and penguin display. -
Page 40: Energy Saving Monitor (Bubble) Screen
Viewing the Energy Saving Monitor Screen (For base unit) Energy Saving Monitor (Bubble) Screen Energy Saving Monitor (Simple) Screen The screen appears as animation with bubbles (circles) and dotted line. The screen appears as simple system diagram. The size of each bubble (circle) changes in 4 levels depending on the size of the value. ( Page 228) Note ● ... -
Page 41: Energy Saving Monitor (Penguin) Screen
Viewing the Energy Saving Monitor Screen (For base unit) ■ Degree of energy saving achievement for this month Energy Saving Monitor (Penguin) Screen ● Degree of energy saving achievement for "This Month" is indicated by the size of the ice and the number of penguins on it. -
Page 42: Checking The Integral Value
Checking the Integral Value (For base unit) The past history of used electricity, used water, and used gas can be displayed as a graph in day, ● Check the integral result For integral electricity consumption month, and year units. ● Select from "Date", "Month", and "Year". -
Page 43: Checking The Time Zone Rate For The Electricity
Checking the Time Zone Rate for the Electricity Checking the Eco Record (For base unit) (For base unit) You can check the time zone rate for the electricity. You can check the past maximum daily electricity consumption record for the unit. Display the Energy Saving Monitor screen Display the Energy Saving Monitor screen Page 73) -
Page 44: Checking The Eco Saving Level
(sold separately). You can also make graphs for the electoricity consumption etc. easily on a PC. Display the Eco Information (Eco ● "Eco-report Creation Tool" is required to display graphs on a PC. Download from Panasonic Note Record) screen webpage to the PC in advance. (As of September, 2016) http://sumai.panasonic.jp/wiring/mansion/windea/ecoreport/... -
Page 45: Living Mode Switching
Living Mode Switching (For base unit) You can set the appropriate state of the base unit for each living mode by selecting the current Switching the Living Mode living mode ("Absence"/"Sleeping"/"Home") if "Living mode: On" is set in the installation setting. Switch the living mode in accordance with the scene. - Page 46 Living Mode Switching (For base unit) Changing Each Setting of Living Mode Touch of the setting you want to change Note The current setting will not change even the setting is changed. Select the living mode again. ● Each setting screen appears. Touch any one Note...
-
Page 47: Return Home Notification Function
Return Home Notification Function Living Mode Switching (For base unit) Return home notification to tell of a family member's return helps you to distinguish a call by Ringtone Volume Ringtone Volume Setting screen a visitor. Sets the Ringtone Volume Setting for Note ●... -
Page 48: Setting According To Your Preferences
Setting According to Your Preferences You can set ringtone volume etc. according to your preferences. ● Only the ringtones volume and touch sound can be set with the call sub-base unit with monitor. Note Consult with the management company or the company that installed the system for installation setting. Setting item Setting content Initial setting... -
Page 49: Setting According To Your Preferences
Setting According to Your Preferences Setting item Setting content Initial setting Page Setting item Setting content Initial setting Page Return Home Intensity 3 Medium Sets if the linked operation of "return home notification to home" is performed together with the unlocking of Notification Setting Intensity 4 Medium... -
Page 50: Setting Notes Sheet
Setting According to Your Preferences Setting Notes Sheet Enter the setting status after the setting is completed as a copy for customer. (Enter setting content or check mark □ Melody 1 □ Melody 2 □ Melody 3 □ On □ Off Yuttari On/Off □... -
Page 51: Starting User Setting
Setting According to Your Preferences Starting User Setting □ Room 1 □ Room 2 □ Bedroom □ Child’s room □ Kitchen Call sub-base unit 1 □ Living room □ Japanese room □ Dining room Extension Setting □ Room 1 □ Room 2 □... -
Page 52: Finishing User Setting
Setting According to Your Preferences Sound Setting Finishing User Setting Press the OFF button to return to the Touch in the Setting screen 終了 waiting state (nothing is displayed ● The Sound Setting screen appears. on the screen) ● For how to start the setting, see page 97. Press Touch Names and Actions of Each Button on the User Setting Screen... - Page 53 Setting According to Your Preferences Accepting Call from Other Unit/Ringtones For other unit Ringtone Volume For base unit Ringtone Volume Setting screen Ringtones screen Note "Other Unit" does not appear unless the setting Touch either of "Off/Low/Medium/High/ on the control device or the integrated control Extra High/Step", and touch panel is performed.
-
Page 54: Not-Home Setting
Setting According to Your Preferences Not-home Setting Touch Sound Touch Sound screen Select either of "ON (Immediately)/ Touch in the Setting screen Off", and touch ● The Not-home Setting screen appears. ON (Immediately) Sounds the touch sound. ● For how to start the setting, see page 97. (Initial setting) Touch Does not sound the touch sound. - Page 55 Setting According to Your Preferences Record the message in following Pretend To Be Out Message screen Pretend To Be Out Message procedure when touched Select one of "Fixed Message Touch 1/Fixed Message 2/Recorded Touch in the Not-home Message Message", and touch screen Touch Touch...
-
Page 56: Auto Record Notice
Setting According to Your Preferences Auto Record Notice Security Setting ● ● This setting is available to only the base unit with video recording function. This setting is available when the security function is installed. Note Note ● ● "Auto Record Notice" does not appear when set to "Notification of new arrivals announcement: Off" by the This cannot be set during security vigilance. - Page 57 Setting According to Your Preferences Set the security number in the following Security Preliminary Alarm procedure when ● This setting is available when set to "Permit changes to delay setting: Yes" with the installation setting. Note is touched (Consult with the management company or the company that installed the system.) ●...
- Page 58 Setting According to Your Preferences ID Authentication Key Off Return Home Notification Setting Set the number of ID authentication key adapted to the condominium. Note "ID authentication key Off" in the Security Setting screen does not appear in the condominium not ●...
- Page 59 Setting According to Your Preferences Extension Setting (Only when Call Sub-base Unit is Connected) Mute Setting ● The return home notification is accepted constantly when the start time and the end time is the same. Note Note ● Operation method of the call sub-base unit 2 is the same as the call sub-base unit 1. (Initial setting: 21:00 to 07:00) ●...
- Page 60 Setting According to Your Preferences Language Private Security Number Setting ● Note "Private Security Number Setting" does not appear unless the setting on the control device or the Touch in the Setting screen integrated control panel is performed. (Consult with the management company or the company that installed the system. ●...
- Page 61 Setting According to Your Preferences Senior Mode Setting SD Card Setting Note Under using the Senior mode, the setting value for each setting item will not return to original even when This can be set when a microSD memory card is inserted. Note set to "No".
- Page 62 Setting According to Your Preferences Extension Light Setting Initialize All the visitor record and recorded data in the microSD memory card will be erased. Save the Note Note ● This is displayed when the door phone with camera is installed and set to "Camera Light Setting: Light necessary data to other devices such as a PC.
- Page 63 Setting According to Your Preferences Mobile Device Adapter Setting (Only When Mobile Device Adapter (Supports Smartphone and Tablet) is Connected) Earthquake Setting Note "Mobile Device Adapter Setting" in the Setting screen does not appear unless the mobile device adapter is Note "Earthquake Setting"...
- Page 64 Setting According to Your Preferences Mobile Device Adapter Information screen EV Setting Mobile Device Adapter Information Information of the mobile device Note "EV Setting" does not appear in the Setting screen if the EV charging system is not installed to the condominium.
- Page 65 Setting According to Your Preferences Initialize Delete Recorded Data Protected visitor records, etc., are not deleted. Perform the delete recorded data again after Note cancelling the protection. (To Cancel Protection page 207) Touch in the Setting screen ● The Initialize screen appears. Delete Recorded Data screen Touch ●...
- Page 66 Electricity Check Setting 0.1 kW 144〜145 can be set. Touch ● The Rate Setting screen appears. The value set by Panasonic Factor to convert the usage ● based on the CO emission The Electricity Unit Price Setting Conversion of the purchased electricity, factor published by 146〜147...
- Page 67 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Enter the unit price and touch Select the contracted rate plan and Touch ● Returns to the Meter-rate Lighting setting the numeric touch to set screen. buttons ● Entered value is erased by touching Meter-rate Lighting ●...
- Page 68 Setting the Energy Saving Monitor (Eco Setting) (For base unit) "Late Night-time Electric Power" is the time zone lighting system to use the electricity Touch in basic rate from late night to morning, when the electrical consumption is low. The name and time Late Night-time ●...
- Page 69 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Set correctly in accordance with the contract with the electrical company. Enter the basic rate and touch Note The discount will not be reflected if this is set incorrectly. Electrification Touch ●...
- Page 70 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Water Rate Setting Touch ● The Unit Price screen appears. The unit price of water (price for 1 m ) can be set. Once set, charge based on the setting is also displayed in the Integral Power screen.
- Page 71 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Gas Rate Setting Touch The unit price of gas (price for 1 m ) can be set. Once set, charge based on the setting is also ● The Unit Price screen appears. displayed in the Integral Power screen.
- Page 72 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Electricity Target Value Setting Set the target value The target value (monthly usage) of the electricity usage can be set from the past actuals or by ● The minimum value that can be set is 100 kW. The screen as directly entering the target value.
- Page 73 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Water Target Value Setting Set the target value The target value (monthly usage) of the water usage can be set from the past actuals or by ● The range of value that can be set is 1 m 100 m .
- Page 74 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Gas Target Value Setting Set the target value The target value (monthly usage) of the gas usage can be set from the past actuals or by ● The range of value that can be set is 1 m to 100 m .
- Page 75 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Electricity Check Setting Set the value The value to be the standard of power consumption state (standby electricity) can be set. ● The initial value is set to 0.1 kW. Displaying of the electricity check (light bulb icon) ( pages 74 to 77) is performed based on this ●...
- Page 76 Factor to convert the usage of the purchased electricity, water, and gas to CO can be set. Touch ● The initial value is set to the value set by Panasonic based on the CO emission factor published ● Returns to the Other Setting screen.
- Page 77 ● "Eco-report Creation Tool" is required to display the data on a PC. Download from ● Touch to return to the previous the Panasonic webpage to the PC in advance. ( Page 83) screen. Touch ● The overwrite confirmation screen appears when there is already data in the microSD memory card.
- Page 78 Setting the Energy Saving Monitor (Eco Setting) (For base unit) History Data Delete The screen in right appears when the delete is completed The measurement data up to that point and various history data saved in the base unit can ●...
- Page 79 Setting the Energy Saving Monitor (Eco Setting) (For base unit) Setting Initialization The screen in right appears when the initialization is completed The contents set in each setting item can be initialized to the initial setting contents. ● Returns to the Other Setting screen after a while.
-
Page 80: Connected System Components In Apartment Units (Example)
Connected System Components in Apartment Units (Example) *1: The extension adapter used for units (sold separately) must be installed to the base unit to use these devices. *2: An extension speaker cannot be connected if two call sub-base units are connected. The following equipment is typically installed in the condominiums. -
Page 81: In The Event Of Fire Or Disconnection
In the Event of Fire or Disconnection Note Confirm that system components are properly installed before using the system. Outbreak of Fire When Using the VGDT Model Base Unit The fire detector activated alarm time After approx. 2 minutes Installer If a sprinkler detects a fire, the operation as described in section 2 Setting can be configured to a value between... - Page 82 In the Event of Fire or Disconnection Outbreak of Fire on the Same Floor or Floor Directly below When Using the VGDT Model Base Unit Outbreak of Fire When Using the VGDB Model Base Unit When the detector detects a fire, the system reports a fire.
-
Page 83: In The Event Of A Gas Leak Or Disconnection
In the Event of a Gas Leak or Disconnection In the Event of Fire or Disconnection Note Confirm that system components are properly installed before using the system. In the Event of Detector Disconnection In the Event of a Gas Leak When detector wiring becomes disconnected, When the gas detector detects gas, the system the system reports a disconnection. - Page 84 In the Event of a Gas Leak or Disconnection In the Event of Imperfect Combustion In the Event of a Gas Detector Fault When the imperfect combustion state (carbon monoxide) is detected by the gas/CO detector, When the gas detector is disconnected or removed, the system reports a fault. the system reports a fault.
-
Page 85: Making Calls
Making Calls Making Emergency Call Alarms Note Note Confirm that system components are properly installed before using the system. Confirm that system components are properly installed before using the system. When the Call Button is Pressed Configure the emergency call alarm as the call function. Installer Setting The emergency call alarm can also be configured as the toilet or bathroom... -
Page 86: Security Alarm Activations
Security Alarm Activations Note Confirm that system components are properly installed before using the system. ● The system can be configured to not stop the alarm approximately 80 seconds after the If a Window Opens While the Security Alarm is Active Installer Setting magnet switch activates. - Page 87 Security Alarm Activations If the Front Entrance Door is Opened While the Security Alarm is Active When the Lock Indicator Appears If the front entrance door is opened while the security alarm is active, the magnet switch activates, ● The Lock OPEN indicator on the base unit is and the system triggers the security preliminary alarm.
-
Page 88: Activating The Emergency Alarm
Activating the Emergency Alarm Security Alarm Activations Note Confirm that system components are properly installed before using the system. 非常 Disarming Security Alarms (disable any active security and security preliminary alarms) (for Base Unit) If the EMERGENCY Button or Other Emergency Button is Pressed EMERG. -
Page 89: In The Event Of Water Leaks
In the Event of Water Leaks Wireless Equipment Failures When the wireless equipment experiences a failure, the system reports a wireless equipment failure. Note Confirm that system components are properly installed before using the system. When the water leak sensor detects a water leak, the system reports a water leak. STOP ALARM ●... -
Page 90: When Electricity Is Overused
When Electricity is Overused The system reports that electricity is being overused when such scenarios occur. LCD Displays and Alarm Messages ● This screen appears when using a distribution panel with over-currency alarm. Note Distribution panels have "limiter ON/OFF" settings. The data output type of distribution panel has "5-stage ● ... -
Page 91: In The Event Of An Earthquake
In the Event of an Earthquake ● These screens appear in a condominium installed with systems that support the Earthquake Note Contact your condominium manager to check if your condominium uses the detailed Early Warning System (prediction). If the elevator earthquake sensor is linked with a system Installer Setting earthquake intensity display or the simplified earthquake intensity display (... - Page 92 In the Event of an Earthquake Using the Detailed Earthquake Intensity Display Using the Simplified Earthquake Intensity Display If the Earthquake Early Warning System (prediction) information When an Earthquake is Expected was incorrect If earthquake alarm (prediction) information is received, the system reports the event with If incorrect information is received, the system reports the event with a screen display and sound.
-
Page 93: When An Elevator Stops
When an Elevator Stops In the Event of an Earthquake ● These screens appear in a condominium in which the Earthquake Early Warning System Note interface board is installed and linked with the elevator system. ● Confirm that system components are properly installed before using the system. Using the Simplified Earthquake Intensity Display When an Elevator Stops When an elevator stops when an earthquake occurs, the system reports the event with a screen... -
Page 94: If An Alarm Occurs During Another Alarm
If an Alarm Occurs During Another Alarm Alarms are assigned priority for situations in which multiple alarms occur at the same time. The following table lists the priority of each alarm. See page 183 for more information on the operations performed when multiple alarms occur at the same time. List of Alarms and Calls Screen Displays When an Alarm Occurs during Another Alarm Alarms/calls for models... -
Page 95: If An Incoming Call Is Received During An Alarm
If an Incoming Call is Received During an Alarm Performing Other Operations During Alarms (For base unit) If you receive a call from the main entrance or building manager room, the caller appears in The system can be operated from the Top Menu screen by shutting off any sounding alarms. the sub-screen, and the alarm message and ringtone are played alternately. -
Page 96: Security Alarms
Security Alarms (For base unit) ● ● The following table lists the default settings for the security system delay time and the preliminary Confirm that system components are properly installed before using the system. Note ● alarm time. The method to arm and disarm the security system varies depending on your condominium building, installed devices, and device settings. -
Page 97: Configure A Security Number Used To Disarm The Security System
Security Alarms (For base unit) Configure a Security Number Used to Disarm the Security System Touch ● This action registers the security number ● The security number can be configured for security systems. Note and displays the Security Setting screen. ●... -
Page 98: Arming All Security System Circuits
Arming All Security System Circuits (For base unit) The security system is armed for both windows and doors at the same time. ● The security system arms immediately for windows and after approximately 60 seconds for the front ● Note When the living mode function is not in use, the screen is displayed the security alarm delay entrance door. -
Page 99: Arming Individual Security System
Arming Individual Security System (For base unit) ● The security system delay start message plays When the "Individual Security System" setting is enabled, the individual window and door circuits of while the user arms the security system. A the security system can be armed separately. sound will be played 30 seconds before the ● ... -
Page 100: Shortening The Security System Delay Time From The Door Phone
Shortening the Security System Disarming the Security System While the Preliminary Alarm is Active Delay Time from the Door Phone (For base unit) The security system can be disarmed for both the front entrance door and windows during Performing the following operations from the door phone enables you to immediately arm the security the preliminary alarm time when returning home. - Page 101 Disarming the Security System While the Security Alarm is Not Active (For base unit) The security system can be disarmed from the Top Menu screen when the security alarm is not active. Enter the security number ● Operation is different when using Living mode while the "Individual Security System" setting (installation setting) is enabled.
- Page 102 Disarming the Security System While the Security Alarm is Not Active (For base unit) When using Living mode "Individual Security System" setting enabled while using Living mode Press the MENU button while Press the MENU button while the security system is armed the security system is armed 復旧/警報音停止...
-
Page 103: Arming The Security Alarm Using The External Security Set Switch
Arming the Security Alarm Using Disarming the Security Alarm Using the External Security Set Switch the External Security Set Switch Arming the Security System Externally Disarming the Security System Externally The external security set switch can be used to arm the security system for the front entrance The external security set switch can be used to disarm the security system for the front entrance door and windows. -
Page 104: List Of Record Management Items
Record Management (For base unit) The record management function can be used to verify visitor and other types of records. How to Start Record Management Operation List of Record Management Items Press the MENU button in the 復旧/警報音停止 RESET/ STOP ALARM waiting state (nothing is MENU Item... -
Page 105: Playing Visitor Records, Camera Monitor Recordings, Building Manager Room Recordings
Record Management (For base unit) Playing Visitor Records, Camera Monitor Recordings, Building Manager Room Recordings, and Voice Mails List Display Screen Screen information display Not viewed: Video recording that has not been viewed ● Select any of the available options Sub-screens are also recorded. -
Page 106: Protecting And Deleting Audio And Video Files
Record Management (For base unit) Protecting and Deleting Audio and Video Files Removing Protection Once the maximum number of recordings has been reached, video can no longer be recorded while absent. Protect any necessary data and delete any unnecessary data. ●... -
Page 107: Playing Emergency Announcements
Lobby Phones Record Management (For base unit) Playing Emergency Announcements Part Names and Functions The figures in the manual illustrate a lobby phone with camera. Select on the Notice ● The following models differ only in the size of the LCD panel. (Records Management) screen ■ Lobby phone with camera ■ Small lobby phone with camera... - Page 108 Lobby Phones Main Entrance Unlock Function Talk Function Calling Unit Unlocking with the Security Number Note Setting of security number is required. (Consult with the management company or the building manager room.) Enter the unit number with the numeric buttons Lobby phone with camera Lobby phone with camera Press the...
- Page 109 Lobby Phones Unlocking with Emergency Unlock Button Unlocking with the Double Auto-lock System The main entrance at the second gate can be unlocked without operation from the visiting unit. The main entrance (electronic lock) is unlocked by pressing the emergency unlock button installed close to the main This can be operated in the condominium building with the double auto-lock function.
- Page 110 Lobby Phones Unit Information Confirmation Method Unlocking with the Panic Open Feature Unit information (delivery in the delivery box, message from the building manager room, alarm information, etc.) can be confirmed upon returning to the unit or at the main entrance The main entrance (electronic lock) is unlocked at the time you have returned home or going out.
- Page 111 Lobby Phones Confirmation Method : Confirmation by the ID Authentication (On Going Out) Confirmation Method : Confirmation by the ID Authentication (On Returning Home) Following linked operation can be performed simultaneously with unlocking of the main Following confirmations are possible with the ID authentication on the lobby phone when going out. entrance (electronic lock) by the ID authentication upon returning home.
- Page 112 Lobby Phones Elevator Link Function The operating rules of the security operation can be temporarily cancelled by unlocking the main Confirmation Method : Confirmation by the Private Security Number entrance and ID authentication operation by the resident, and the elevator can be operated even if the elevator is operated in security operation.
-
Page 113: Expire Date Of The Gas Alarm
Expire Date of the Gas Alarm Troubleshooting ● An expiration date is defined to maintain the function of the gas alarm connected to the base unit. Stop the alarm sound with the STOP ALARM button when the alarm of the base unit or the call sub-base ●... - Page 114 Troubleshooting Perform following inspections and measures before requesting repair or service. Measure Condition Inspection ● Is the breaker of the base unit tripped? (100 V) Turn ON the breaker of the base unit with monitor. (100 V) Does not operate at all Is the power supply for the intercom power supply turned ● ...
- Page 115 Troubleshooting Perform following inspections and measures before requesting repair or service. Condition Inspection Measure Note The ringtones volume is low Is the ringtones volume setting set to "Low" or "Medium"? Set the ringtones volume setting to "High". Ringtone Volume Setting page 101 Note The sound during calling or playback is low...
-
Page 116: Specifications
Specifications For indoor use only List of Alarms and Calls Fire detector "(Siren) The fire detector has been activated. VGDT18143W activated alarm VGDT18543W Please check." VGDT item number only VGDT18643W VGDB18143W VGDT18743W "(Siren) Warning, fire, fire. Warning, fire, fire. VGDT18145W VGDB18145W Fire confirmation Item number... -
Page 117: Notice Regarding Software
Simplified earthquake Confirm the information of this license at following support site. (As of September, 2016) intensity display http://www2.panasonic.biz/es/densetsu/ha/mansion_ha/windea/license/index.html "(Beep) We are now beginning an earthquake alarm test. (Siren) Earthquake coming. Intensity 6-lower. (Siren) Earthquake coming in 20 seconds. Intensity 6-lower, (siren). -
Page 118: Faq
"Cont" appears 10 seconds before the call is ended. Touching "Cont" once will extend Panasonic and its related companies shall use personal information of customers for answering questions and to provide better repair support. The conversations between customers and the assistance service is recorded. We also ask you to notify the call for approximately 1 minute.