Advertisement
Quick Links
OnePass Hitch
ProCore
Model No. 09753—Serial No. 310000001 and Up
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
© 2010—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Processor
Description
Link pin
Hex nut
Washer
Support arm, R.H.
Support arm, L.H.
Washer
Jam nut
Lynch pin
Hitch cross
Screw (1/2 x 2 inches)
Washers
Locknuts (1/2 inch)
Link pin
Lynch pin
Link pin
Lynch pin
Pin assembly
Screw (1/2 x 1-3/4 inches)
Washers
Locknuts (1/2 inch)
Pipe spacer
Pivot hitch
Washer
Locknut (1 inch)
Tow arm, R.H.
Tow arm, L.H.
Flag pin
Screw (3/8 x 1–1/4 inch)
Flange nut
Mount tab
Screw (1/2 x 2–1/4 inch)
Washer
Locknut
Hitch pin
Lynch pin
Register at www.Toro.com.
Form No. 3361-617 Rev A
Installation Instructions
Qty.
2
2
2
1
1
2
4
2
1
8
16
8
Mount the support frame
1
1
1
1
1
4
8
4
4
1
2
1
1
1
2
2
2
Mount the tow-arms
1
4
8
4
2
Mount the core processor to the aerator
2
Use
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Related Manuals for Toro ProCore 09753
Summary of Contents for Toro ProCore 09753
- Page 1 Screw (1/2 x 2–1/4 inch) Washer Locknut Hitch pin Mount the core processor to the aerator Lynch pin Register at www.Toro.com. © 2010—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420 All Rights Reserved...
- Page 2 Procedure Note: If the aerator is mounted to the tractor, the aerator must be lowered and the disconnected from the tractor. Mounting the Support Frame 1. Install the link pins to the support arms as follows: A. Thread a hex nut onto each link pin (Figure 1). Parts needed for this procedure: Insert a washer onto each link pin.
- Page 3 3. Secure the lower hitch cross tab to the aerator bracket with link pin and lynch pin (Figure 6). Figure 6 Figure 3 1. Lower hitch cross 3. Lynch pin 1. Link assembly 4. 26.27 to 28.11 inches 2. Link pin 4.
- Page 4 6. Connect the hitch upper link to hitch cross tab and 9. Mount the pin assembly to the back of the hitch secure with link pin and lynch pin (Figure 8). cross with 4 screws (1/2 x 1-3/4 inch), 8 washers and 4 locknuts (Figure 10).
- Page 5 2. Secure the mount tab between the front of the tow-arms with 4 screws (1/2 x 2-1/4 inch), 8 washers and 4 locknuts. Position the tab as shown in Figure 13. Use the front set of holes for the 660 Mounting the Tow-Arms aerator and the rear set of holes for 864 and 880 aerators.
- Page 6 • Connect the control link to the rear holes in the frame hitch pivot when operating a ProCore 660 aerator. • Connect the control link to the front holes in the frame hitch pivot when operating ProCore 864 and 880 aerators. Figure 14 1.
- Page 7 Notes:...
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.