Panasonic AW-HE130WP Operating Instructions Manual page 41
Hd integrated camera
Hide thumbs
Also See for AW-HE130WP:
- Operating instructions manual (126 pages) ,
- Installation instructions manual (24 pages) ,
- Operating instructions manual (126 pages)
Table of Contents
Advertisement
Parts and their functions (continued)
Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address
AUTO
1
2
SW1
OFF
ON
OFF
SW2
OFF
ON
ON
SW3
OFF
ON
ON
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-232C is enabled.
When this is set to OFF, the RS-422 is enabled.
3
4
5
6
7
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
Simultaneous output conditions for each video
„
format
z SDI/HDMI/VIDEO output
Format
HD/SDI
1080/59.94p
1080/50p
1080/59.94i
1080/50i
1080/29.97psF
1080/25psF
1080/23.98psF
1080/29.97p
1
*
1080/25p
1
*
1080/23.98p
720/59.94p
720/50p
SD/SDI
480/59.94p
576/50p
480/59.94i
576/50i
*
1
Native output
*
2
480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z IP video transmission output (1-/multi-channel display)
1-channel display
Resolution
1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
Frame
59.94Hz 1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
rate
60 fps
*
1
50Hz
1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps
*
1
60 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
*
2
50 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Multi-channel display
Setting
H.264 CH1
Resolution
1920×1080
1280×720
Frame
59.94Hz
60fps
rate
50Hz
50 fps
*
3
Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
SDI
HDMI
VIDEO
output
output
output
2
*
2
*
2
*
H.264 CH2
H.264
JPEG
CH3/CH4
CH1/CH2/
CH3
*
1920×1080
1280×720
1920×1080
1280×720
640×360
1280×720
640×360
320×180
640×360
320×180
160×90
320×180
160×90
160×90
5 fps
5 fps
1 fps
15 fps
15 fps
2 fps
30 fps
30 fps
3 fps
5 fps
6 fps
10 fps
15 fps
30 fps
5 fps
5 fps
1 fps
12.5 fps
12.5 fps
2 fps
25 fps
25 fps
5 fps
10 fps
12.5 fps
25 fps
3
41
Advertisement
Table of Contents
