Page 1
Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : LP69G MODEL: M228WA (M228WA-BZH.A**QLP) ) **Same model for Service CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
Page 9
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 10
General Soldering Guidelines Replacement 1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board. appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad and solder it.
Page 11
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the "lift-off"...
DISASSEMBLY 1. Push down slightly to disassembly it. Push the button. 2. After push the cable management like above fig.(Downward), Disassembly the Cable management with pulling it upward. 3. Disassembly Cable Holder. Hold the stand base. Disassembly Stand base. Remove base body Like a picture. Push 2 letches Like a picture.
Page 13
Pull base body to separate from set during pressing 2 letches. 1. Remove the screws. 2. Disassembly Hinge Cover. # 10 Remove the screws. Disassembly back cover. # 11 Pull the connector. - 13 -...
DESCRIPTION OF BLOCK DIAGRAM 1. Power Supply Block (LIPS) This Block Generates DC Voltage (5V,15V) to Main Control system from AC Power (100-240 V, 50/60 Hz, 1.0A) 2. DC/DC Converter block DC/DC Converter convert the input 5V,15V to proper 1.8V,2.5V,3.3V,5V,10.5V for Main control system. For shooting heat trouble, we use the DC/DC converting IC 3.
Page 16
LIPS Board Block Diagram 50 ~ 60Hz 100KHz HVDC ENERGY INPUT RECTIFIER OUTPUT RECTIFIER TRANSFER COMPONENTS AND FILTER AND FILTER LINE 100 ~ 240V SIGNAL PHOTO COLLENT- CONTROL -COUPLER CIRCUIT ISOLATION PRIMARY SECONDARY Operation description_LIPS 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
Page 18
ADJUSTMENT INSTRUCTION 1. Application Range This specification sheet is applied to 19"/ 20"/ 22" LCD Monitor TV which is manufactured in TV (or Monitor) Factory or is produced on the basis of this data. 2. Specification 1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing.
Page 19
4.3. Confirm color coordinate of AV2 (1) Set Input to AV2 (2) Input signal : CVBS, PAL @ 50Hz Full white 216/255 gray level (85 IRE, Model : 202, Pattern : 78 at MSPG925L) (3) Set PSM : Dynamic / CSM : Cool (4) Confirm whether x = 0.285±0.03, y = 0.293±0.03 or not.
Page 20
(5) DVI 2) DIGITAL DATA 256Byte *M198WA - Select input DVI model 112(1440*900@60hz), 64 Gray Scale pattern and whether picture is displayed or not *M208WA / M228WA - Select input DVI model 122(1680*1050@60hz), 64Gray pattern and whether picture is displayed or not. 4.7.
Page 21
4.11. Internal pressure *M198WA/M208WA/M228WA(Change by Suffix) Area Option 00 - Confirm whether is nomal or not when between power Item Condition Remark board's ac block and GND is impacked on 1.5kV(dc) or Option1(6) 2.2kV(dc) for one second. 200PR 0 : 200 PR Off 4.12 Option data setting (SVC OSD setting) 1 : 200 PR On (1) PAL Model...
Page 22
(2) Command Set 5. Adjustment Command 5.1. Adjustment Commands(LENGTH=84) Adjustment contents CMD(hex) ADH(hex) ADL(hex) Details EEPROM READ 0-Page 0~7F Read Adjustment Contents Description (hex) 0-Page 80~FF Read FACTORY ON Factory mode on 1-Page 0~7F Read FACTORY OFF Factory mode off 1-Page 80~FF Read EEPROM ALL INIT.
Page 23
SERVICE OSD BLUEBIRD3 - LP69G Description of operation - Tool Option : Adjust Tool Option Version 2.01 061227 - Area Option : Adjust Area Option M228WA WSXGA CMO-22W - Option 1 : Adjust Tuner Service Option - Option 2 : Adjust Sound Service Option - Option 3 : Adjust Local key Tool Option 8066...
TROUBLESHOOTING GUIDE 1. NO POWER (LED INDICATOR OFF) : [A] Process Fail Check 15V or Check 15V or ST_5V of Power B/D. ST_5V of Power B/D. Pass Fail Fail Re-soldering of Change Check Output of Check short of defect part of IC100, Q307. IC1100, IC1101.
Page 25
2. NO RASTER : [B] Process Fail Check LED status Repeat A PROCESS. On Display Unit. Pass Fail Change Panel Link Cable Check Panel Link Cable or Module. or Module. Pass Check Inverter Fail Change Inverter Connector Connector or inverter. or Inverter.
Page 26
3. NO RASTER ON RGB SINGAL Repeat [A, B] process. Pass Fail Check the input/ output Check the J701. of R708, R709 Pass Check Fail Re-soldering or Change the the input/output defect part. of R128, R131, R136. Pass Re-soldering or change the Fail Check the input/output of defect part, Check the...
Page 27
4. No Raster on Component Signal Repeat [A, B] process. Fail Check the input/ output Check the J900. of R901. Pass Fail Re-soldering or Change the Check the input/output defect part. of R125. Pass Re-soldering or change the Fail Check the input/output of defect part, Check the IC100.
Page 28
5. No Raster on DVI Signal Repeat [A, B] process. Pass Re-soldering or change the X100 Fail Check the input/ output defect part, Check the of R100. X100. Pass Check input source cable and jack. 6. No Raster on AV(Scart in 7.
Page 29
8. No sound Fail Check the input Sourse. Change the source input. Pass Re-soldering of Change the Fail Check input/Output defect part, Check the ofIC100. X100 Pass Fail Re-soldering of Change Check the input/ output the defect part. of IC500 Pass Fail Change Speaker.