Advertisement
Available languages
Available languages
Quick Links
g
GE
Lighting Solutions
READ THOROUGHLY BEFORE INSTALLING
Save instructions for future use.
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
G E N E R A L
This luminaire is designed for use in outdoor applications and
should not be installed in areas of limited ventilation or in high
ambient temperature enclosures. This fixture should be installed
and maintained according to the following recommendations.
U N P A C K I N G
This luminaire has been packed so that no parts should have
been damaged during transit. Inspect to confirm.
INSTALLATION
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
General:
Fixture access: To open, apply slight downward pressure to the
front of the door frame and pull latch. To close fixture, close door
until latch engages.
Mounting Plate Installations:
Install fixture onto sign structure and securely fasten using the
mounting plate/bracket.
Mounting Plate installation is for uplight only. Please call
manufacturer regarding other mounting options.
Figure 1
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's purposes, the matter should be referred
to GE Lighting Solutions.
Fixture Mounting Bracket
Silicone Sealant
White Wire
Wire Connectors (3)
Black Wire
Ground Wire
J-Box
IMPORTANT: In order to provide a watertight seal, the
installer must seal the area around the knock-out holes, with
a type of caulking compound such as GE 100% silicone.
Slipfitter Installation:
Rout fixture leads through the Arm Fitting (provided by
others) connect to power leads (provided by others). Mount
fixture slipfitter to the Arm Fitting and secure by using (4) set
screws (provided) as illustrated in Figure 1.
If the Fixture is mounted in a position other than the horizon-
tal, use care that the lens door does not abruptly swing down and
injure someone. In order to mount at top of sign to be used as a
downlight, user needs to order fixture as a V3ST which includes
rain shield.
IMPORTANT: In order to comply with established electrical
code, the installer must seal the area around the Fixture Slipfitter
and the Arm Fitting, with a type of caulking compound such as
GE 100% silicone.
WIRING
For electrical connections, refer to wiring diagram on
ballast or HF generator.
Make all electrical connections in accordance with the
National Electrical Code and any applicable local code
requirements.
Verify that supply voltage is correct by comparing it to
nameplate.
Draw Pull
Latch (2)
Mogul Base
Socket
Socket Set
Screws (2)
Arm Fitting
(by others)
INSTRUCTIONS
Versaflood III
Fixture Door
and Diffuser
GEH-5959C
™
Advertisement
Related Manuals for GE Versaflood III
Summary of Contents for GE Versaflood III
- Page 1 GE 100% silicone. ambient temperature enclosures. This fixture should be installed and maintained according to the following recommendations.
- Page 2 LAMP INSTALLATION/REPLACEMENT Connect ground lead to the green lead, green ground screw on housing or terminal block provided. Use only lamps specified on nameplate. Observe lamp Do not remove insulated connectors from wires not needed manufacturer’s recommendations and restrictions on lamp for required voltage connection.
- Page 3 Ces instructions n'ont pas pour destination de couvrir tous les détails ou variantes de l'équipement, ni de répondre à toutes les éventualités que vous pourriez rencontrer pendant l'installation, le fonctionnement ou l'entretien. Si vous souhaitez des informations complémentaires, ou si vous rencontrez un problème particulier qui ne soit pas adressé de votre point de vue d'acheteur, le sujet doit être remonté jusqu'à la société GE Lighting Solutions...
- Page 4 4 3 5 3 3 GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company. © 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.