Toshiba D-VR4SU Service Manual page 7
Hi-fi vcr & dvd video recorder
Hide thumbs
Also See for D-VR4SU:
- Owner's manual (88 pages) ,
- Service manual (9 pages) ,
- Owner's manual (88 pages)
Advertisement
Introduction
Connections with the TV or audio component
The exact arrangement you use to interconnect various video
and audio components to the DVD/VCR is dependent on the
model and features of each component. Check the Owner's
Manual provided with each component for the location of video
and audio inputs and outputs.
Connect to a TV with Audio/Video output
You can enjoy playback by connecting the unit to a TV.
Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.
Video output
Audio (L) output
Audio (R) output
Audio/video cable (supplied)
DVD/VCR
Connect to a TV with S-Video output
If your TV has an S-Video input, you can get higher quality by connecting it with the S-Video output of the unit using
the S-Video cable instead of connecting the video input of the TV to the video output jack of the unit.
Audio cable (not supplied)
S-Video cable (not supplied)
DVD audio (L) output
DVD/VCR
DVD audio (R) output
Connect to a TV with Component video output (for DVD/CD playback)
You can enjoy the highest quality picture by connecting the unit's component video out jacks to the component
video input jacks of your TV, with component video cables (not supplied).
Audio cable (not supplied)
Component
video output
DVD audio (L) output
DVD/VCR
DVD audio (R) output
NOTES:
• When connecting to a TV using the video or S-Video jack, make sure that the progressive indicator on the
display window is not lit. If it is lit, the video and S-Video outputs do not feed the correct signals and you cannot
see any picture. To turn off the progressive indicator, make the progressive scanning mode inactive (see page
47).
• If the component video input jacks on a TV are the BNC type, use an adapter to convert the RCA jacks from the
component video cables to BNC (not supplied).
20
Introduction
Auto clock setting / Setting the video channel
Auto clock setting
Preparation:
You must connect the antenna or cable before connecting the AC cord
to the power source.
Wait at least 3 minutes with the power turned off, after the antenna or
cable is connected, for the auto clock feature to activate.
After the clock is set automatically, you may have to set the time zone
and daylight saving time. (See page 26.)
Press ON/STANDBY to turn on the DVD/VCR after the auto clock op-
eration completed.
• When shipped from factory, the "AUTO CLOCK" option is set to "ON"
position.
• If you turn the DVD/VCR on during auto clock setting, the clock is not
set.
• Dependimg on the reception condition, auto clock setting may take
approx. 30 minutes.
• After a power failure or disconnection of the power plug, the clock will
be lost. In this case, wait 3 minutes before turning the DVD/VCR on.
• With cable box connection, if the auto clock setting is unsuccessful,
select the PBS channel carrying the XDS information, then turn the
DVD/VCR off. After 3 minutes, turn the DVD/VCR on.
• If the clock is not set automatically, set the clock manually. (See page
26.)
Setting the video channel
To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be
set to channel 3 or 4 (video channel).
When a TV is connected with the 75 ohm coaxial cable only:
1
Press and hold 3 or 4 on the remote control for 3 seconds in the
standby mode to select CH 3 or 4. The selected channel number
will flash on the display for about 4 seconds.
2
Turn ON the TV and set to CH 3 or 4 to correspond with the chan-
nel selected in step 1.
3
Press ON/STANDBY to turn on the DVD/VCR.
4
NOTES:
Press TV/VIDEO to select the VIDEO position.
• When shipped from factory, the
The TV indicator will disappear in the display.
video channel is set to CH 3.
5
• If the unit does not operate prop-
Select any channel to receive a TV station in your area.
erly, or there is no key operation
The channel number will appear on the screen for about 4 sec-
from the unit and/or the remote
onds.
control: Static electricity, etc., may
For a push-button TV tuner
affect the operation. Disconnect
If CH 3 or 4 corresponding to the video channel cannot be tuned on
the AC power cord once, then con-
your TV, proceed as follows: set the VCR 3/4 channel selector and the
nect it again.
TV to CH 3 or 4, playback a prerecorded tape and tune the TV to re-
ceive a sharp color picture from the video cassette recorder. Refer to
your TV owner's manual for details.
22
The unauthorized recording, use, distribution,
or revision of television programs, videotapes,
DVDs and other materials, is prohibited under
the Copyright Laws of the United States and
other countries, and may subject you to civil
and/or criminal liability.
TV
To Video input
To Audio (R) input
To Audio (L) input
To Audio (L) input
To Audio (R) input
TV
To S-Video
input
S-Video output
TV
To Audio (L) input
To Audio (R) input
To Component
video input
Component video cable (not supplied)
Connections with the TV or audio component
Connect to a stereo amplifier with audio output
You can enjoy high quality audio by connecting the audio output to your amplifier.
Connect the audio output jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.
Audio (L) output
To Audio (L) input
Audio cable (not supplied)
DVD/VCR
Audio (R) output
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the optical or coaxial digital output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
Video cable (not supplied)
Coaxial digital audio output
Video output
Coaxial digital
cable (not supplied)
DVD/VCR
Connecting the optical digital cable
You may connect to an AV Amplifier with an optical digital cable (not supplied) instead of a coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The DVD OUTPUT jacks (OPTICAL, COAXIAL, AUDIO L/R and COMPONENT) are useful only for DVD
section. The VHS signal is output only from the S-Video output jack, composite jacks (DVD/VCR OUT-
PUT) and UHF/VHF OUT.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input
connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may
cause such a high level of noise that it may be harmful to your ears and damage your speakers.
• DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is
necessary.
• When playing DTS-encoded CDs, only noise will be heard from the speakers or analog stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
• The optical or coaxial digital output jack output sounds in the bitstream.
Various settings
SETUP MENU
The SETUP MENU consists of several menus where
you can make various settings concerning lan-
guage, audio functions, and images. In addition, this
menu includes a clock, channel and other things
that require setting just after purchase.
For details of each menu, see the corresponding
section in this chapter.
Using the SETUP MENU
The following example shows the basic setting proce-
dure of the SETUP MENU. The remote control keys
that operate the SETUP MENU are displayed at the
bottom of the screen.
1
Press SETUP while the DVD or video tape is
stopped.
The SETUP MENU screen will appear.
SETUP MENU
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
SELECT
ENTER
ENTER
RETURN
BACK
SETUP
END
2
Press
or
to select the desired menu and press
ENTER.
The submenu screen of the selected menu will ap-
pear.
SETUP MENU
TIMER REC SET
LANGUAGE
SYSTEM SETUP
PARENTAL
AV SETUP
CLOCK
REC SETUP
DISC SETUP
CH SETUP
OTHER
OTHER
SELECT
ENTER
ENTER
RETURN
BACK
SETUP
END
Stereo Amplifier
To Audio (R) input
NOTE:
You may connect to a TV with a component
video cable (not supplied) or S-Video cable
(not supplied) instead of a video cable (not
supplied).
To Video intput
TV
AV Amplifier with built-in various
decoder as above
21
3
Press
or
to select the desired submenu and
press ENTER.
The screen for the selected submenu will appear.
SETUP MENU
TIMER REC SET
LANGUAGE
SYSTEM SETUP
ENGLISH
OSD LANGUAGE
AV SETUP
DVD MENU
ENGLISH
REC SETUP
AUDIO
ENGLISH
SUBTITLE
AUTOMATIC
CH SETUP
OTHER
SELECT
ENTER
ENTER
RETURN
BACK
SETUP
END
4
Press
or
to select the desired item you want,
and press ENTER.
Selectable items will be listed.
SETUP MENU
TIMER REC SET
LANGUAGE
SYSTEM SETUP
OSD LANGUAGE
ENGLISH
AV SETUP
DVD MENU
ENGLISH
REC SETUP
AUDIO
ENGLISH
SUBTITLE
AUTOMATIC
CH SETUP
ENGLISH
OTHER
FRANCAIS
ESPANOL
OTHER
----
AUTOMATIC
OFF
SELECT
ENTER
ENTER
RETURN
BACK
SETUP
END
5
Press
or
to select the desired item and press
ENTER.
This completes the setting procedure.
• To return to the previous screen, press RETURN.
• To close the SETUP MENU, press SETUP.
NOTES:
• For items that require different operations from the
basic setting procedure, the setting procedure is de-
scribed in each individual section.
• The item which is indicated by blue color cannot be
selected.
23
- Quick Links:
- Table of Contents
Hide quick links:
Advertisement
