Toshiba Tosvert VF-S15 Series Instruction Manual page 69
Rs485 communication function
Hide thumbs
Also See for Tosvert VF-S15 Series:
- Instruction manual (394 pages) ,
- Quick start manual (90 pages) ,
- Function manual (80 pages)
Table of Contents
Advertisement
Command parameters
For those parameters that contain data only in the RAM and not in the EEPROM, their data return
to initial values when the power is turned off, in failure resetting, or when standard shipment settings
are set. Note that parameters without data storage in the EEPROMs will be written in the RAM
only even if the command W (writing in EEPROMs and RAM) is executed.
Commands
C ommunica-
tion
Num-
ber.(HEX)
FA00
FA01
FA03
FA08
FA10
FA11
FA13
FA20
FA26
FA50
FA51
FA65
FA66
FA67
FA68
FA70
FA71
FA72
FA73
FA74
FA75
FA76
FA77
FA78
FA79
FA80
FA87
1
＊
:Enable the communication command or communication frequency setting before setting these
parameters are set.
communication" for the method to enable them.
2
＊
:See "8.1. Communication commands (command from the computer)" for the detail information.
3
＊
:See "8.3. Utilizing panel (LEDs and keys) by communication" for the detail information.
Monitor parameters
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Function
Communication command 1
1
＊
(RS485)
Frequency command value
1
＊
(RS485)
Operation panel operation fre-
quency
Local/Remote selection
3
＊
Panel key selection
External communication key
3
＊
data
Motor speed command (FA13) 0 to 24000min
Communication command 2
1
＊
(RS485)
Communication command 3
O utput data on the terminal
2
＊
board
2
＊
FM analog output
Select display by communica-
3
＊
tion
3
＊
Numerical display data
3
＊
Decimal point position
3
＊
LED data for unit 0
ASCII display data 1
3
＊
First digit from left
ASCII display data 1
3
＊
Second digit from left
ASCII display data 1
3
＊
Third digit from left
ASCII display data 1
3
＊
Fourth digit from left
3
＊
LED data for unit1
ASCII display data 2
3
＊
First digit from left
ASCII display data 2
3
＊
Second digit from left
ASCII display data 2
3
＊
Third digit from left
ASCII display data 2
3
＊
Fourth digit from left
3
＊
LED data for unit 2
Block communication mode
Reset information
Otherwise, the parameters will not function.
*These Parameters are read-only (monitor-only) parameters.
68
Note: Data is expressed in decimal notation.
Adjustment Range
Setting
0 to 65535
0 to Max. frequency
0.01Hz
( fh )
Low-limit frequency
0.01Hz
( ll ) to High-limit
frequency ( ul )
0:Remote
1:Local
0: Main unit
1: Communication
0 to 65535
-1
0 to 65535
0 to 65535
0 to 255
0 to 100.0
(resolution of 10 bits)
0 to 2
0-9999
0 to 2
0 to 3
0 to 127
0 to 255
0 to 255
0 to 127
0 to 3
0 to 127
0 to 255
0 to 255
0 to 127
0 to 3
3
＊
0 to 1
0 to 255
E6581913
Min.
Write
Initial
EEP
During
Value
ROM
Operation
Unit
-
0
yes
None
0
yes
None
0
yes
Available
-
0
yes
Available
-
0
yes
None
-
0
yes
None
-1
1min
0
yes
None
-
0
yes
None
-
0
yes
None
1
0
yes
None
0.1%
0
yes
None
-
1
yes
Available
1
0
yes
Available
-
0
yes
Available
-
0
yes
Available
-
100
yes
Available
(' d ')
-
65
yes
Available
(' a ')
-
116
yes
Available
(' t ')
-
yes
Available
65
(' a ')
-
yes
Available
0
-
48
yes
Available
(' 0 ')
-
48
yes
Available
(' 0 ')
-
yes
Available
48
(' 0 ')
-
yes
Available
48
(' 0 ')
-
0
yes
Available
-
0
yes
Available
-
0
yes
None
See "8.1. Command by
Hide quick links:
Advertisement
Table of Contents
