GE C70 Instruction Manual page 330

Capacitor bank protection and control system
Hide thumbs Also See for C70:
Table of Contents

Advertisement

PRODUCT SETUP
PUSHBTN 1 ID TEXT
intended to provide ID information of the pushbutton. For example, the text displays in the Event Record. See the User-
definable Displays section in this chapter for instructions on how to enter alphanumeric characters from the keypad. On a
graphical front panel, this setting instead controls the label of the user-programmable pushbutton component on single-
line diagrams.
PUSHBTN 1 ON TEXT
and is displayed when the pushbutton is in the "on" position. See the User-definable Displays section for instructions on
entering alphanumeric characters from the keypad. On a graphical front panel, this setting instead controls the on status
text of the user-programmable pushbutton component on single-line diagrams. This setting is not applied to the physical
pushbuttons on the graphical front panel.
PUSHBTN 1 OFF TEXT
and displays when the pushbutton is deactivated and the
display when the
PUSHBUTTON 1 FUNCTION
release. The length of the "Off" message is configured with the
setting. On a graphical front panel, this setting instead controls the off status text of the user-programmable
TIME
pushbutton component on single-line diagrams. This setting is not applied to the physical pushbuttons on the graphical
front panel.
— This setting specifies the time required for a front panel pushbutton to be pressed before it is deemed
PUSHBTN 1 HOLD
active. This timer is reset upon release of the pushbutton. Note that user-programmable pushbutton operation requires the
front panel pushbutton to be pressed a minimum of 50 ms. This minimum time is required prior to activating the user-
programmable pushbutton hold timer.
— This setting assigns the FlexLogic operand serving to activate the user-programmable pushbutton
PUSHBTN 1 SET
element. The duration of the incoming set signal must be at least 50 ms.
— This setting assigns the FlexLogic operand serving to deactivate the user-programmable pushbutton
5
PUSHBTN 1 RESET
element. This setting is applicable only if the user-programmable pushbutton is in "Latched" mode.
PUSHBTN 1 AUTORST
only if the pushbutton is in "Latched" mode.
PUSHBTN 1 AUTORST DELAY
mode.
PUSHBTN 1 REMOTE
operation from the operand assigned to the
— This setting assigns the FlexLogic operand serving to inhibit user-programmable pushbutton operation
PUSHBTN 1 LOCAL
from the front panel pushbuttons. This inhibit functionality is not applicable to pushbutton autoreset.
PUSHBTN 1 DROP-OUT TIME
programmable pushbutton active status after the front panel pushbutton or graphical front panel interface pushbutton
has been released. When activated remotely, this setting specifies the entire activation time of the pushbutton; the length
of time the operand selected by
PUSHBTN 1 LED CTL
setting is "Off," then LED operation is directly linked to the
Pushbuttons 9 to 16 on the graphical front panel, where the label background shows the orange glow color for the "on"
state.
PUSHBTN 1 MESSAGE
programmed in the
off message that is programmed in the
graphical front panel.
When set to "Disabled", user-programmable pushbutton messages do not display. Otherwise the on message displays
when the user-programmable pushbutton becomes activated, and if in the "Latched" mode the off message displays when
the user-programmable pushbutton becomes deactivated.
When set to "Normal", the duration the message displays is as specified by the
5-126
— This setting specifies the top 20-character line of the user-programmable pushbutton message and is
— This setting specifies the bottom 20-character line of the user-programmable pushbutton message
— This setting specifies the bottom 20-character line of the user-programmable pushbutton message
is "Self-reset" as the pushbutton operand status is implied to be "Off" upon its
— This setting enables the user-programmable pushbutton autoreset feature. This setting is applicable
— This setting specifies the time delay for automatic reset of the pushbutton when in "Latched"
— This setting assigns the FlexLogic operand serving to inhibit user-programmable pushbutton
PUSHBTN 1 SET
— This setting applies only to "Self-Reset" mode and specifies the duration of the user-
remains on has no effect on the pulse duration.
PUSHBTN 1 SET
— This setting assigns the FlexLogic operand serving to drive the front panel pushbutton LED. If this
— This setting controls the behavior of the user-programmable pushbutton on message that is
and
PUSHBTN 1 ID
PUSHBTN 1 ON TEXT
PUSHBTN 1 ID
PUSHBUTTON 1 FUNCTION
PRODUCT SETUP  DISPLAY PROPERTIES  FLASH MESSAGE
or
PUSHBTN 1 RESET
operand. This setting is not applied to
PUSHBUTTON 1 ON
settings, and the behavior of the user-programmable pushbutton
and
PUSHBTN 1 OFF TEXT
C70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUAL
CHAPTER 5: SETTINGS
is "Latched." A message does not
settings.
settings. This settings has no effect on the
setting.
FLASH MESSAGE TIME

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents