LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE LISHED BY SONY.
Page 3
Mettre au rebut les batteries usagées conformément aux instructions du fabricant. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. 1 (P) BVM-D32E1WA/D32E1WE/D32E1WU...
[Convergence Adjustment] ............... 3-11 [G2 Adjustment] ..................3-12 [White Balance Adjustment] ..............3-13 4. Safety Related Adjustments +B (135V) Voltage Adjustments ..............4-1 High Voltage Regulator Check/Adjustment ..........4-1 High Voltage Hold-Down Check/Adjustment ..........4-1 Beam Current Protector Check ..............4-2 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 6
E Board and EA Board ................6-14 6-6. D1 Board ....................6-17 6-7. BUF2 Board ....................6-18 7. Semiconductors ............. 8. Exploded Views 8-1. Cover ......................8-2 8-2. Card Slot ...................... 8-3 8-3. Picture Tube ....................8-4 9. Electrical Parts List ............BVM-D32E1WA/D32E1WE/D32E1WU...
Page 7
BK (5/9) ....................11-11 BK (6/9) ....................11-12 BK (7/9) ....................11-13 BK (8/9) ....................11-14 BK (9/9) ....................11-15 BK1 ......................11-18 BC (1/4) ....................11-20 BC (2/4) ....................11-21 BC (3/4) ....................11-22 BC (4/4) ....................11-23 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 8
BC ......................11-24 BUF2 ....................... 11-34 PC, C ....................... 11-37 E ......................11-38 EA ......................11-44 G ......................11-46 D1 ......................11-49 DC ......................11-51 PA ......................11-55 HD, YA, YB, YC ..................11-57 TA1 ......................11-59 TB ......................11-61 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 9
TRINITRON COLOR VIDEO MONITOR ® BVM-D20F1U/D20F1E/D20F1A BVM-D24E1WU/D24E1WE/D24E1WA BVM-D32E1WU/D32E1WE/D32E1WA OPERATION MANUAL [English] 1st Edition (Revised 3) Serial No. 2000001 and Higher...
Page 10
CAUTION: WARNING: THIS WARNING IS APPLICABLE FOR USA For the customers in Europe (BVM-D20F1E/D20F1A, WARNING Danger of explosion if battery is incorrectly replaced. ONLY. BVM-D24E1WE/D24E1WA, BVM-D32E1WE/D32E1WA) Replace only with the same or equivalent type recommended This product with the CE marking complies with both the To prevent fire or shock hazard, do not by the manufacturer.
Page 11
Voor de klanten in Nederland For the customers in United Kingdom (BVM-D20F1E/ ATTENTION - When the product is installed in a rack: Achtung - bei Installation des Geräts in einem Gestell: D20F1A, BVM-D24E1WE/D24E1WA, BVM-D32E1WE/ a) Elevated operating ambient temperature a) Erhöhte Umgebungstemperatur bei Betrieb Bij dit produkt zijn batterijen geleverd.
Page 12
Table of Contents Precautions ....................3 Chapter 1 Overview Overview ....................4 Features ..................4 Options ................... 5 Connector Panel Configuration ............7 Installing a Decoder Adaptor ............9 Location and Function of Parts ............10 Front Panel ................... 10 Rear Panel ..................
Page 13
If you have any questions about this unit, contact your image is hidden by the mask. To display the 4:3 Connection Cable Specifications for Color Temperature Probes 69 authorized Sony dealer. image, replace the 16:9 mask with the supplied 4:3 Menu Index ................... 71 mask.
• Pulse cross function for simultaneous checking of the For effective picture size, see “Specifications” on page 62. horizontal and vertical synchronization signals. ® 2) Trinitron is a registered trademark of Sony Corporation. 3) For details on the signal format, see “Available Signal Formats” on page 65.
http://getMANUAL.com Overview BKM-26M PAL-M Decoder Adaptor Decoder and input expansion adaptors Connector Panel Configuration Includes decoders for analog composite PAL-M signals and input/output connectors for six analog The input connector panel is configured by sliding the The unit comes standard with connectors for one BKM-41HD BKM-42HD BKM-48X...
Overview BKM-20D BKM-21D BKM-22X BKM-24N BKM-25P BKM-26M BKM-27T BKM-28X Installing a Decoder Adaptor Adaptor SDI 4:2:2 SDI Multi NTSC PAL-M Tri- Analog name Decoder Decoder Input Decoder Decoder Decoder Standard Input Signal Adaptor Adaptor Expansion Adaptor Adaptor Adaptor Decoder Expansion Each decoder adaptor can be installed in any input Push the adaptor in until it is firmly seated in the format...
Location and Function of Parts 1 Tally lamp Front Panel With factory settings, the tally lamp lights when pins No. 8 and No. 9 of the REMOTE 2 connector on the BVM-D20F1U/D20F1E/D20F1A rear panel are shorted. By changing the setting in the REMOTE menu, different pins on the remote connector can be used to control the tally lamp.
Location and Function of Parts 1 MAIN POWER switch 5 Analog input/output connectors Rear Panel When turned on, the monitor enters operation mode. By setting in the SYSTEM CONFIGURATION menu, ANALOG the monitor can also be set to enter standby mode BVM-D20F1U/D20F1E/D20F1A when the MAIN POWER switch is turned on.
Location and Function of Parts 7 REMOTE 1 connectors (female, D-sub 9-pin) BKM-10R Monitor Control Unit (Optional) Pin number Function Set input signal channel 1 (numeric keypad REMOTE 1 function) This manual explains the location and function of parts Note Set input signal channel 2 (numeric keypad and controls of the optional BKM-10R Monitor If you press the UP/DOWN buttons or ENTER button...
Page 20
Location and Function of Parts 6 DEGAUSS button 9 MANUAL adjustment buttons and knobs Function buttons in SHIFT OFF mode (LEDs of function buttons in green) Press to degauss the CRT (every time the monitor is Each press of one of these buttons turns the button’s turned on, the CRT is degaussed automatically).
Page 21
1080/48I, 1080/50I or 720/60P format. To receive the 1080/48I, 1080/50I or 720/60P format signal, consult your adjust CHROMA and to check VTR noise. authorized Sony dealer. R/G/B buttons: When these buttons are pushed in (ON), R(red), G(green), and B(blue) beams are cut respectively.
Installation of the 4:3 Mask Location and Function of Parts (BVM-D20F1U/D20F1E/D20F1A only) When the BVM-D20F1U/D20F1E/D20F1A aspect Inserting/ejecting the BKM-12Y Memory Monitor Card ratio is switched from 16:9 to 4:3, replace the 16:9 mask with the supplied 4:3 mask. Proceed as illustrated to insert and eject an optional Note BKM-12Y Monitor Memory Card.
Basic Menu Operations Menu Operation Buttons Displaying the Menus Menu Operation Press the MENU button. Follow the steps described below to display the menu The menus are operated using the menu operation and perform the adjustment or setup you wish. buttons on the BKM-10R Monitor Control Unit (optional).
Page 24
Basic Menu Operations Repeat steps 2 and 3 until the desired menu is Press the ENTER or Ent button. Choosing one of two or more selections Entering a numerical value displayed. “?” is displayed in yellow. The “?” indicates the For more information about setting and adjustments, position where character input is possible.
http://getMANUAL.com Menu Structure Basic Menu Operations Menus consist of two to six levels. The Main Menus Detailed information on the levels of menus is ADDRESS Menu displayed on the Menu List and Level 1 are shown described at the top of explanation of each menu. below.
Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ Menu [A1] PRESET menu/CH SET menu 7COLOR BAR 100%: 100% full-field 7-color bar Overview Select the setting method. (white, yellow, cyan, green, magenta, red and MANUAL... : Set with the MANUAL knobs. ÷[A11] blue) (with 100% white signal, not selectable for The preliminary adjustments of contrast, brightness, •...
(PROBE menu) (100IRE) ON CRT You can use the following probes for automatic adjustment of color temperature. Except for the Sony BKM-14L, a cable is required to connect the color COPY FROM B13 OTHER VALUE B131 analyzer to the monitor.
• If you cannot execute an ADJUST or ANALYZE Setting Lists in the COLOR TEMP ADJ Menu The following message appears. Perform operation menu operation when using the Sony BKM-14L according to the message to enable the BKM-14L to probe, try again after disconnecting and reconnecting...
[C1] Setting the Input Configuration (SET UP 1) B Adjusting the Color Temperature — COLOR TEMP ADJ Menu — INPUT CONFIGURATION Menu [B1321] MONITOR ADDRESS menu TRIM: Select whether to add the fine adjustment to Overview Select STD, COL1, COL2, or CH SET. ÷ Copy is the original setting (gain and bias set in MANUAL carried out.
[C1] Setting the Input Configuration (SET UP 1) — INPUT CONFIGURATION Menu Setting Lists in the INPUT CONFIGURATION Menu Structure of the INPUT CONFIGURATION Menu This section explains the setting lists displayed in the CONTROL: Use if either PRESET or CH SET Level 1 Level 2 Level 3...
Page 31
[C1] Setting the Input Configuration (SET UP 1) — INPUT CONFIGURATION Menu [C14] SAFE AREA MODE menu [C16] COLOR TEMP menu Notes Note Set the safe area display modes. Select STD, COL1, COL2 or CH SET. • Even when selecting AUTO, also select NTSC The size of the safe area for the 16:9-xx% or 4:3-xx% SIZE: Select the safe area mode.
[C2] Assigning the Remote Control Functions (SET UP 2) — REMOTE Menu Setting Lists of the REMOTE Menu Overview The remote control functions are set with the This section explains the setting lists displayed in the [C221] 1-8 PIN menu (1/2) About monitor address and group numbers REMOTE menu.
[C3] Setting the Password (SET UP 3) — PASSWORD Menu [C3] PASSWORD menu Overview Enter the password for the PASSWORD menu. ENTER PASSWORD: Enter the password (factory A four-digit password can be specified and applied to Use of the password setting: 9999).
[C4] Setting the Channel Selection Method, Power-Up Conditions and Decoder (SET UP 4) — SYSTEM CONFIGURATION Menu Overview Setting Lists of the SYSTEM CONFIGURATION Menu The SYSTEM CONFIGURATION menu is used for • Residual subcarrier detection (RESIDUAL SC This section explains the setting lists displayed in the DEFAULT CH: Select the power-up input channel the following settings: SW menu) (when using the BKM-24N/25P)
http://getMANUAL.com [C5] Setting the Screen Display (SET UP 5) — ON SCREEN SET Menu Overview Setting Lists of the ON SCREEN SET Menu The ON SCREEN SET menu is used to select the type • Caption vision (CAPTION VISION menu) [C52] FORMAT DISPLAY and POSITION menus This section explains the setting lists displayed in the of information that will be displayed on the screen and...
[C6] Adjusting Geometry and Convergence (SET UP 6) — ALIGNMENT Menu [C6] ALIGNMENT menu (1/3) H PIN BAL: Correct the balance of side pincushion Overview Adjust the position or size of the picture with the UP distortion. and DOWN buttons or PHASE knob. The ALIGNMENT menu is used for adjusting •...
[C7] Adjusting Beam Landing and Digital Uniformity (SET UP 7) — WHITE [C6] Adjusting Geometry and Convergence (SET UP 6) — ALIGNMENT Menu UNIFORMITY Menu (BVM-D24E1WU/D24E1WE/D24E1WA/D32E1WU/D32E1WE/D32E1WA only) [C61] CONV FINE ADJUST menu (BVM- Turn Turn Overview counterclockwise. clockwise. D32E1WU/D32E1WE/D32E1WA only) Adjust the convergence finely at each adjustment point The following two adjustments can be performed using Note...
When you are adjusting the gain using the MANUAL NORTH, NORTH EAST, EAST, SOUTH EAST, The following message appears, and the cursor moves AUTO... : Automatically adjust using the Sony BKM- adjustment knobs, you can reset the setting to the one SOUTH, SOUTH WEST, WEST or NORTH WEST 14L Auto Setup Probe.
[C8] Using Extended Functions (SET UP 8) [C7] Adjusting Beam Landing and Digital Uniformity (SET UP 7) — WHITE UNIFORMITY Menu — EXTEND Menu In the same way, adjust each adjustment point guided (2) Place the BKM-14L to the cursor displayed in the Overview by the cursor.
Monitor Memory Card Data Operations [C8] Using Extended Functions (SET UP 8) — EXTEND Menu — MEMORY CARD Menu [C8] EXTEND menu • System data and MEMORY CARD data ([D]) cannot Overview Enter the password (ENTER PASSWORD [C81]) be stored on the same memory card. To store memory When the correct password is entered, the following card data, use another memory card.
Displaying Information About the Monitor Monitor-to-Monitor Data Copy — COPY FROM Menu — STATUS Menu Overview Overview The STATUS menu is used to view general data about • Data about the current channel (STATUS menu When multiple BVM-DxxE/DxxF series monitors are First assign the MONITOR ADDRESS from which the monitor status, the current channel, etc.
Selecting the Monitor to Control — ADDRESS Menu By pressing the ENTER or Ent button after selecting Overview Cancelling the Remote Control Short-cut Function in the the item, serial remote operation becomes activated. Mode ADDRESS Menu Address number selected with the When multiple monitors are connected by a serial Address Short-cut function remote connection, the ADDRESS menu is used to...
Page 43
Specifications Effective picture size with 4:3 aspect Nominal chromaticity coordinates: General Input/output connectors ratio: SMPTE C phosphor (BVM-D32E1WU) 361.6 × 271.2 mm (14 × 10 System 15.625 kHz – 45 kHz (For details, see inches) Video input BNC type × 3 (with loop-through “Available Signal Formats”...
Specifications Synchronization Standard luminescence Storage and transport conditions Acquired safety regulations BVM-D20F1U/D20F1E/D20F1A/ D24E1WU/D24E1WE/D24E1WA: Vertical blanking time Temperature UL1950, CSA No.950 100 cd/m (at standard 1 Vp-p 100% Less than 650 µs. –10°C to 40°C (14°F to 104°F) FCC Class A, IC Class A white signal) Horizontal blanking time Humidity...
http://getMANUAL.com Specifications BVM-D24E1WU/D24E1WE/D24E1WA Dimensional Drawing With BKM-10R attached Unit: mm (inches) Unit: mm (inches) BVM-D20F1U/D20F1E/D20F1A Front Front 565.5 (22 565.5 (22 With BKM-10R attached Unit: mm (inches) Unit: mm (inches) Front Front 444 (17 444 (17 460 (18) 470 (18 328 (13) Side Side...
Special cables are required to connect color The following diagrams show specifications and pin Unit: mm (inches) Bottom Front temperature probes other than the Sony BKM-14L to assignments for the required cables. 794 (31 the monitor. Connection cable for GRASEBY SLS 9400 probe...
Menu Index Specifications The menu index shows the menu items provided with Connection cable for PHILIPS PM 5639 probe (corresponds to PHILIPS PM 5639/64 this monitor in alphabetical order. For you reference, cable) each menu item is followed by the page of this manual on which the item is explained, its menu number, and Modular connector Mini DIN 8-pin connector...
Page 48
LOAD [D2] MEMORY CARD menu SLOT STATUS [F31] STATUS menu [C816] MAINTENANCE SET UP/EXTEND menu [B121] SONY BKM-14L COLOR TEMP ADJ menu MANUAL [A11] CONTROL PRESET ADJ menu START [B12111] COLOR TEMP ADJ menu [B11] COLOR TEMP ADJ menu STATUS...
Page 49
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any...
Geometry and Convergence Adjustments SYSTEM CONFIGURATION Settings of the channel selection method, power-up conditions and decoder The following illustrations show the geometry and convergence adjustments using the ALIGNMENT menu (1/3). INPUT CONFIGURATION INPUT SELECT DIRECT MODE 1) Contrast and brightness settings for H PIN REMOTE STANDBY MODE...
(Claw case screw OS) 6 Side cover (R) 5 Four screws 4 Side cover (L) (Claw case screw OS) 2-2-2. PA Board Open Hinge 1 Two screws (+P4 x 8) CN905 2 Open the PA board Hinge in the direction of arrow. BVM-D32E1WA/D32E1WE/D32E1WU...
Battery removal 7 Z board (Extension board) note) Insert the Z board into the slot and insert the E board into the connect on the Z board. 1 Loosen the two screws. 2 Remove the E board. (+B4 x 20) BVM-D32E1WA/D32E1WE/D32E1WU...
BC board within five minutes. 2 Remove the BK board. (Stopper screw) 4 Remove the BC board. 5 Z board (Extension board) note) Insert the Z board into the slot and insert the BK board into the connect on the Z board. BVM-D32E1WA/D32E1WE/D32E1WU...
8 Two screws (+BVTT3 x 6) 9 YC board 5 YA board CN301 4 Two claws 2 Two screws (+B4 x 10) CN101 CN201 3 Bezel assy 6 Screw (+BVTT3 x 6) 7 YB board 1 Two screws (+B4 x 10) BVM-D32E1WA/D32E1WE/D32E1WU...
(2) Do not press the rubber so hard that it damages the inside of anode caps. A shatter-hook terminal is built into the rubber. (3) Do not turn the foot of the rubber over. The shatter-hook terminal will stick out or damage the rubber. BVM-D32E1WA/D32E1WE/D32E1WU...
14. Copy the data of step 13 to MODEs 6, 23 and 24. (Table 1) 15. Apply locking paint to [F1] and [F2] of focus pack. 7. Repeat steps 5 and 6 until the best focus in all steps of 5 and 6 at the same time. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 63
1152/50i (31 kHz) 16:9N MODE 16 1125 16:9U MODE 32 1120 16:9U Table. 1 For the MODE 29 through 32, all the adjustment work is only to enter the initial value to the memory area. → Do not make any adjustment. BVM-D32E1WA/D32E1WE/D32E1WU...
Be careful not to adjust the DY inclination too excessively so as to adversely affect the convergence.) 15. Fix the deflection yoke using the four DY spacers. (Confirm DY inclination and the DY position in the front and rear directions.) Fig. 1-2 BVM-D32E1WA/D32E1WE/D32E1WU...
Signal area data and fix the purity magnet with white paint. H CENTER A = B Note: Use the Auto Setup Probe (BKM-14L) as much as possible and perform the automatic adjustment. H PHASE C = D Fig. 1-6 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 66
6. H CENTER H BLK RIGHT H PHASE Copy the above data to the following mode. H BLK LEFT MODE6 16:9 UNDER SCAN H BLK RIGHT Copy the above-described data to the following modes. MODE16 1125 16:9 UNDER SCAN BVM-D32E1WA/D32E1WE/D32E1WU...
6. Adjust the V CENTER data and adjust the vertical center of the image. 7. Input the HD (1125) cross-hatch signal. 8. Adjust the VSIZE, V LIN BAL, and V LIN data as shown in Fig. 1-8. V LIN BAL V LIN AMP Fig. 1-8 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 69
V SIZE V CENTER H SIZE H LIN BAL V LIN H LIN H CENTER V LIN BAL H KEY BAL H KEY H PIN BAL H PIN V SIZE H SIZE V LIN H CENTER Fig. 1-10 Fig. 1-11 BVM-D32E1WA/D32E1WE/D32E1WU...
22. Change the SCREEN MODE of modes 17 to 32 as well, and perform adjustments in the same way. (Refer to Table 1 (page 3-3)) Fig. 1-13 2. Correction of 6-pole magnet VMC (vertical mis-conver- gence) and movement of electronic beam Fig. 1-14 3-10 BVM-D32E1WA/D32E1WE/D32E1WU...
Adjust the VMC (vertical mis-convergence) correction using the 6-pole magnet of the neck assembly. (Refer to Fig. 1-2.) 2 Counter-clockwise direction 3 Clockwise direction Fig. 1-17 4 Adjustment by opening/closing in slant position Fig. 1-16 3-11 BVM-D32E1WA/D32E1WE/D32E1WU...
DY correction reactors APH and TLH. Deflection yoke DY spacer H.TRP Neck assy C board Fig. 1-19 V STAT TOP V STAT BOTTOM Fig. 1-18 3-12 BVM-D32E1WA/D32E1WE/D32E1WU...
Use the color analyzers for this adjustment after calibrat- C board – Side B – ing them so that they will show the correct measured Fig. 1-21 values at the following chromaticity coordinate. 3-13 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 74
COLOR2. 11. Select AUX of COLORTEMP, select the value shown in the following tabel, and copy the color temperature data to AUX. COL 1 COL 2 AEP, AUS 3-14 BVM-D32E1WA/D32E1WE/D32E1WU...
13. If RV503 has been replaced at step 9, fix it with epoxy 8. Remove the static voltmeter. resin (made by DP-190 3M) after adjusting the RV. 9. If RV501 has been replaced at step 7, fix it with epoxy resin (made by DP-190 3M) after adjusting the RV. BVM-D32E1WA/D32E1WE/D32E1WU...
Specifications : 1.61 mA to 2.10 mA 11. Turn OFF the power. 12. Remove the jumper from between TP502 and TP504 (GND) of the PA board. 13. Turn ON the power again. BVM-D32E1WA/D32E1WE/D32E1WU...
..Before starting the adjustment, turn the digital uniformi- 11. Frequency characteristics adjustment ty (DU) to OFF (0) is the lower layer of the MAINTE- NANCE. Set DU to ON (1) upon completion of the BK adjustment. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 80
SLOT No. 6 RV100 CV100 RV300 75Ω terminater x 4 Signal generator CV300 (1125/60 Hz 2:1 color bar) BK board (100 IRE RGB color bar) Extension board/cable kit RV500 (part cord : A-1394-806-B) CV500 BK board –Side A– BKM-10R BVM-D32E1WA/D32E1WE/D32E1WU BVM-D32E1WA/D32E1WE/D32E1WU...
Page 82
• Connect an oscilloscope to TP502. Equalize the TP502 pedestal and clamp The adjustment menu is • After adjusting, set the CHROMA offset pulse. B-Y CLAMP OFFSET located data to 1000. inside the BK BOARD menu of the MAINTENANCE menu. This portion BVM-D32E1WA/D32E1WE/D32E1WU...
Page 83
..Set the CHROMA data to 1000 inside the BK BOARD menu of R-Y GAIN (+) using the CHROMA knob. the MAINTENANCE menu. (Note: At CONTROL PRESET) ..Connect an oscilloscope to TP305. Flatten B-Y GAIN (+) BVM-D32E1WA/D32E1WE/D32E1WU...
The adjustment menus are to TP305 and TP505. the TP305 and TP505 outputs are equal: G 100 IRE and B 100 IRE Level difference : 0 ± 2 mV located inside the BK BOARD menu of the MAINTENANCE Adjust menu. BVM-D32E1WA/D32E1WE/D32E1WU...
The black levels of the TP305 and TP505 outputs are The adjustment menus are to TP305 and TP505. equal to the SETUP signal level: G SETUP and B SETUP Level difference : 0 ± 2 mV located inside the BK BOARD menu of the MAINTENANCE Equalize menu. BVM-D32E1WA/D32E1WE/D32E1WU...
• Adjust CV100 so that the waveform satisfies the standard. Note: Adjust so that the 25 MHz marker becomes 0 If unadjustablecompletely using dB, and check if the above standard is satis- fied. CV100, adjust to satisfy the standard while tracking with RV100 and CV100. BVM-D32E1WA/D32E1WE/D32E1WU...
If unadjustable completely using CV500, adjust to satisfy the standard while tracking with RV500 and CV500. 12. Reference Refer to 5-1. Basic Adjustments When Replacing CRT for details of the following adjustments. G2 adjustment White balance adjustment BVM-D32E1WA/D32E1WE/D32E1WU...
Section 6 Circuit Descriptions This section describes the circuits of the following boards used in the BVM-D32E1WA/D32E1WE/D32E1WU. 6-1. BK Board 6-2. PA Board 6-3. BC Board 6-4. G Board 6-5. E, EA Board 6-6. D1 Board 6-7. BUF2 Board 6-1. BK Board 1.
Page 90
The BRT voltage is generated in IC701 (1/3) by switching the BRIGHT voltage and BRT CENTER voltage in the pulse (100 IRE pulse, SET UP pulse) insertion period and in other periods. The same is performed for the B and G signals. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 91
SCLK, and outputs the control signal according to the instructions of the system controller. It also reads the adjustment data of the EEP ROM (IC903) (when setting the data from the BC board to the D/A), and outputs the adjustment voltage from the D/ A converter (IC906 to 911). BVM-D32E1WA/D32E1WE/D32E1WU...
As the result, the high voltage converter stops its operation and the high voltage output is held down. IC501 has the latch function with D517 and D518 so that the low state is maintained once the comparator output goes low. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 93
The G2 regulator circuit is controlled by the G2 control voltage that is supplied from the BK board so that the optimum cathode voltage is obtained. At the same time, the power supply voltage for this circuit is the high voltage that is obtained by rectify- ing the drain pulse voltage at Q109. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 94
Basic structure of the correction circuit is shown below. The respective blocks are described one after another. Direction correction data Direction correction signal Partial correction signal NS coil LCC coil Temperature sensor Ambient temperature correction signal LCC drive LCC coil LCC coil ABL signal Beam current correction signal LCC coil BVM-D32E1WA/D32E1WE/D32E1WU...
Page 95
TOP LEFT EAST, SOUTH EAST TOP RIGHT SOUTH, SOUTH WEST BOTTOM LEFT BOTTOM RIGHT WEST, NORTH WEST RESET Select an appropriate direction from the eight patterns that provides most uniform landing over the entire screen. Menu for landing correction. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 96
The circuit that is prepared to cancel the difference is connected to IC622 pin-5. CRT screen Directions of the landing change when the ambient temperature increases. (Directions are inverted when the ambient temperature decreases.) BVM-D32E1WA/D32E1WE/D32E1WU...
Page 97
The respective correction signals are added and inverted by IC620, IC621 and IC622 (1/2) for respective five coils. These signals are outputted to the optional amplifiers IC700, IC701 and IC702 via switches IC623 and IC624, which drive the respective correction coils. BVM-D32E1WA/D32E1WE/D32E1WU...
The internal signals are generated from the 27 MHz clock. Data of the internal signals is stored in the video RAM (IC804). The video RAM data is supplied from the CPU. The sample pulse that is used for automatic chroma phase adjustment, is also created here. 6-10 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 99
IC107 generates the H. sync signal generator circuit for 15 kHz signal. Because the H. sync signal of PLD deteriorates of its skew during the fast forward mode of VCR, the H. sync signal is separately created for the 15 kHz signal. Rise-up of this signal is the timing of the H. delay. 6-11 BVM-D32E1WA/D32E1WE/D32E1WU...
The heater power is switched ON/OFF by IC102 that is controlled by the HV CTRL signal of the E board. -7 V power is stabilized to -5 V by IC103 and is supplied to the comparator IC203. 6-12 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 101
PH901 so that the main power supply is stopped of its operation by turning off the Vcc power that is supplied to IC1 and IC201. The protector mode is notified to the CPU on the E board using the encoder/latch circuit that consists of Q801 through Q813. 6-13 BVM-D32E1WA/D32E1WE/D32E1WU...
H. DY is controlled by the H. CENT signal that is supplied from IC7005. . Horizontal linearity circuit The H. LIN signal that is outputted from IC205 on the D board is amplified by Q201 to Q207, drives T3 (HLT) to flow the horizontal linearity correction current. 6-14 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 103
H. STAT coil of the DY is controlled. . V convergence circuit The V. CONV signal that is outputted from IC204 of the D board is amplified by IC801 that drives NTC or the V. STAT coil of DY. 6-15 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 104
IC710 and IC711 (24 inch models) of the PA board. The following protect detection signals are transmitted from IC7001 to IC1 of the BK board. H. STOP, V. STOP, +B. PROT, HV_OVP, IK_PROT, HV_OCP, G. PROT1 to G. PROT4 6-16 BVM-D32E1WA/D32E1WE/D32E1WU...
The DFY signal is generated by adding the signals of DFX. PHASE, DFY. T&B and V. PARA+ signals by IC207 (1/2) 6. Horizontal convergence correction signal generator circuit The H.SAW and the H.PARA signals are added and inverted in IC207 (2/2) where the H.CONV signal is generated. 6-17 BVM-D32E1WA/D32E1WE/D32E1WU...
Real time processing is required for normal data read-out. However, because re-writing data is required during adjustment, writing-down is performed by interrupt processing that stops reading data from SRAM. 6-18 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 107
(i.e., data is eventually interpolated by hardware and software.) In the digital convergence control, every other data is skipped in the H direction. In other words, number of vertical lines of cross- hatch signal is 16, and the data between the adjacent vertical lines are created by interpolation. 6-19 BVM-D32E1WA/D32E1WE/D32E1WU...
Les composants identifiés par la marque ! sont critiques pour la sécurité. • The construction parts of an assembled part are indicated with a Ne les remplacer que par une pièce portant collation number in the remarks column. le numéro spécifié. BVM-D32E1WA/D32E1WE/D32E1WU...
Page 126
8-759-011-65 IC MC74HC4053F-T2 IC125 8-759-476-12 IC EL2082CS-TE2 IC531 8-749-014-06 IC VPJ05 IC126 8-759-476-12 IC EL2082CS-TE2 IC532 8-759-700-78 IC TL082CPS-E20 IC127 8-759-700-78 IC TL082CPS-E20 IC700 8-759-988-13 IC LM393PS-E20 IC128 8-759-011-65 IC MC74HC4053F-T2 IC701 8-759-011-65 IC MC74HC4053F-T2 IC702 8-759-011-65 IC MC74HC4053F-T2 9-10 BVM-D32E1WA/D32E1WE/D32E1WU...
CHR G CONTORL CHARACTOR CONT H8 TXD1 UNIT CHR B H8 RXD1 IC805 DRIVE IC100,101 Q451-457 H8 SCLK1 CHR R IC103,105 H BLK CHR BLANK CONT V BLK1 BUFF V BLK2 AFC PULSE SAMPLE PULSE Overall (1/2) 10-1 10-1 BVM-D32E1WA/D32E1WE/D32E1WU...
E PULSE (2/2) SENCE X103 IC106 IC108 CK IN IC107 14.5MHz 525/625 BUFF BUFF PULSE CC CVI (2/2) Q405 Q404 VITC-DTSE CC Y (2/2) D0-7 A0-4 Y IN RCSI CPU, Signal Generator, Parallel I/O BC Block (1/2) 10-3 10-3 BVM-D32E1WA/D32E1WE/D32E1WU...
IC313 DRIVE REF (4/4) IC504 CH LEVEL (4/4) IC113 BIAS REF (4/4) W & D P (4/4) BIAS P (4/4) CHAR G CHAR B CHAR R Signal Processor BK Block (2/4) Signal Amp, Video Control BK1 Block 10-6 10-6 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 167
DRIVE SAMPLING P (4/4) WHITE SAMPLING P (1/2,2/4,4/4) Signal Output BIAS CLAMP P (4/4) BLACK SAMPLING P (1/4,2/4,4/4) BK Block (3/4) BIAS & DRIVE P (4/4) TP700 IC706 G2 REF (4/4) RGB Output BLK (4/4) C Block 10-7 10-7 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 170
15 VIN H V IN A L MOSI V IN B L SCLK V OUT A IC204 RESET V OUT B V OUT C V OUT D DF BLK H/V Wave From Generator, D/A Converter, DFX Mod. D1 Block 10-10 10-10 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 171
D.F.Y D.F.Y HV CONT BOARD D.F.X D.F.Y D.F.Y D.F.X BOARD IC801 (2/2) D.F.X CN101 D.F.X V CONV V CONV V STAT V STAT H PARA V STAT RTN V STAT RTN Sub CPU, H/V Osc. E Block 10-11 10-11 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 172
5V SENSE IC104 STBY 5V +5V SENSE OPTION PH801 STBY 5V PROT +135V IC802 OCP COMP STBY 5V OCP IC802 IC802 +135V IC802 OVP COMP IC801 STBY 5V OVP 2.5V +135V Main Regulator G Block POWER ON DEGAUSS 10-12 10-12 BVM-D32E1WA/D32E1WE/D32E1WU...
If results do not meet the specified value, change the component marked and repeat the adjustment until the specified value is achieved. • When replacing a part shown in the table below, be sure to perform the related adjustment. 11-1 11-1 BVM-D32E1WA/D32E1WE/D32E1WU...
D_5V SENCE D_GND D_GND G OUT G OUT D_GND D_GND AFC.P AFC.P CK IN APT ON/OFF APT ON/OFF CH_SLOT2 CH_SLOT2 IK_PROTECT IK_PROTECT HV_OVP HV_OVP 525/ B IN B IN BUF2 B OUT B OUT OPTION (2/2) B-SS9698UC-KESSENZU-P3 11-4 11-4 BVM-D32E1WA/D32E1WE/D32E1WU...
R DRIVE IK R DRIVE V (8/9) VIDEO R PROCESSOR R267 -0.8 -0.6 :RN-CP B.U ON/OFF CONT DRIVE AMP IC122(1/2) PROTECTOR VIDEO OUT TL082 -5V-1 IC122(2/2) DRIVE V AMP TL082 CONTRAST AMP,PULSE INSERT DRIVE V AMP B-SS9698UC-BK-P3 11-9 11-9 BVM-D32E1WA/D32E1WE/D32E1WU...
G DRIVE V (8/9) :RN-CP G DRIVE IK (8/9) R467 (4/9) -0.6 -0.6 :RN-CP CONTRAST AMP,PULSE INSERT COMPARATOR, IC322(1/2) -5V-1 IC322(2/2) TL082 VIDEO OUT,VIDEO AMP,DRIVE AMP, DRIVE V AMP TL082 DRIVE V AMP VIDEO G PROCESSOR B-SS09698UC-BK-P4 11-10 11-10 BVM-D32E1WA/D32E1WE/D32E1WU...
220k B DRIVE IK B DRIVE V (8/9) :RN-CP (5/9) R667 (8/9) -0.4 -0.5 :RN-CP IC522(1/2) CONTRAST AMP,PULSE INSERT,PROTECTOR, TL082 IC522(2/2) DRIVE AMP,VIDEO OUT,VIDEO AMP, DRIVE V AMP -5V-2 TL082 VIDEO B PROCESSOR DRIVE V AMP B-SS9698UC-BK-P5 11-11 11-11 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 193
EL4094CS-TE2 (IC701) V IN B V IN A V GAIN V GAIN V OUT TC4W53FU(TE12R) (IC100, 300, 500, 703) COMMON OUT IN LOGIC LEVEL CONVERTOR OUT IN -A SIDE- -B SIDE- SUFFIX: -13 SUFFIX: -13 11-19 11-19 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 200
PROJECT REGISTER LOGIC 32X32 COMMAND DECODE 32X32 CONTROL LOGIC 64X32 WRITE TC4W53FU (IC891) CONTROL MAX490ECSA-TE2 (IC14) TIMING LOGIC COMMON Y DECODE HOLD DATA REGISTER OUT IN LOGIC LEVEL CONVERTOR OUT IN MC74HC4053FEL (IC102, 810) TC74VHC138FT(EL) (IC10, 13) 11-26 11-26 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 201
TL1451ACPWR (IC1101) X DECODE 512 BYTE WRITE STATUS LOGIC ARRAY PROJECT REGISTER LOGIC 32X32 COMMAND 32X32 DECODE V REF CONTROL LOGIC ERROR AMP 2 64X32 WRITE ERROR CONTROL AMP 1 TIMING OSCILLATOR LOGIC Y DECODE HOLD DATA REGISTER 11-27 11-27 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 210
JW(15) JW(15) 0.01 100V R804 R807 3.9k 1.3k CN801 TO BK BOARD 2.2µH 2.2µH TO BK BOARD :MINI IK IN IK OUT JW(+15V) (RGB OUT) JW(+15V) (F.B.T) B-SS9698UC-PC-C C Board Waveforms 33.2Vp-p (2H) 39.4Vp-p (22H) 39.4Vp-p (2H) 11-36 11-36 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 211
PC, C PC, C -B SIDE- SUFFIX: -12 -B SIDE- SUFFIX: -12 11-37 11-37 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 230
SLR-325DCT31 SLR-325DCT31 SLR-325DCT31 CN14 4a-7a TALLY IND TALLY IND TALLY IND TALLY IND TALLY IND 4b-7b D102 D104 D106 D108 J301 SLR-325DCT31 SLR-325DCT31 SLR-325DCT31 SLR-325DCT31 TALLY IND TALLY IND TALLY IND TALLY IND (CONNECT) B-SS9698UC-YC (TALLY) B-SS9698UC-YA 11-56 11-56 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 231
HD, YA, YB, YC HD, YA, YB, YC -A SIDE- SUFFIX: -11 -B SIDE- SUFFIX: -11 -A SIDE- SUFFIX: -11 -B SIDE- SUFFIX: -11 -A SIDE- SUFFIX: -11 -B SIDE- SUFFIX: -11 -B SIDE- SUFFIX: -11 11-57 11-57 BVM-D32E1WA/D32E1WE/D32E1WU...
Page 232
STBY 5V STBY 5V -30V DIGITAL+5V DIGITAL+5V DIGITAL+5V -30V -30V DIGITAL+5V DIGITAL+5V DIGITAL+5V DIGITAL.GND DIGITAL.GND DIGITAL.GND POWER ON POWER ON POWER ON DIGITAL.GND DIGITAL.GND DIGITAL.GND IK_PROTECT IK_PROTECT IK_PROTECT _CH.SLOT2 _CH.SLOT1 HV_OVP HV_OVP HV_OVP INTERNAL.SIG INTERNAL.SIG INTERNAL.SIG (MOTHER) B-SS9698UC-TA1 11-58 11-58 BVM-D32E1WA/D32E1WE/D32E1WU...