Table of Contents
Advertisement
en | 3 2 | User guide | OBD 2220 Info Scan
IPT (MOD $09)
OBDCOND
IGNCNTR
CATCOMP1
CATCOND1
CATCOMP2
CATCOND2
O2SCOMP1
O2SCOMD1
OBD Monitoring Conditions Encoun
•
In the above examples, Module $09 returned
data. Scroll down to view information. CVNs are
shown as hexadecimal numbers.
•
Abbreviations and names for in-use performance
tracking data supported by the tool are shown
below. Not all data is supported by all vehicles.
Abbreviated
Expanded Name
Name
In-Use Perf
In-Use Performance Tracking
Tracking
OBD Monitoring Conditions Encountered
OBDCOND
Counts
IGNCNTR
Ignition Counter
Catalyst Monitor Completion Counts
CATCOMPX
Bank x
Catalyst Monitor Conditions Encoun-
CATCONDX
tered Counts Bank x
O2 Sensor Monitor Completion Counts
O2SCOMPX
Bank x
O2 Sensor Conditions Encountered
O2SCONDX
Counts Bank x
EGR Monitor Completion Condition
EGRCOMP
Counts
EGR Monitor Conditions Encountered
EGRCOND
Counts
AIR Monitor Completion Condition
AIRCOMP
Counts (Secondary Air)
AIR Monitor Conditions Encountered
AIRCOND
Counts (Secondary Air)
EVAP Monitor Completion Condition
EVAPCOMP
Counts
EVAP Monitor Conditions Encountered
EVAPCOND
Counts
•
If message INVALID displays on screen, the data
returned from the vehicle is incorrect, or is not
formatted in accordance with OBDII specifications.
4.
Return to Vehicle Information menu.
•
Press
.
5.
Return to Diagnostic Menu.
•
Press
.
580000 | REV. A | 04.2017
0
0
0
0
0
0
0
0
Rd\Er
6
Troubleshooting
6.1
Error Messages
Check the following if an error message displays:
•
Verify ignition key is in the ON and not in the ACCES-
SORIES position.
•
Make sure the DLC Cable is attached to vehicle's
data link connector (DLC) and scan tool.
•
Look at DLC and check for cracked or recessed pins,
or for any substance that could prevent a good
electrical connection.
•
Test for continuity between the DLC wiring and the
computer. In an extreme case, there may be a bro-
ken wire.
•
Check for bent or broken pins.
•
With the engine off, check for blown fuses in the
vehicle fuse box.
•
Make sure the vehicle's control module has a good
ground. If the computer case is grounded, then
clean the connection and apply a conductive (dielec-
tric) grease to the mating surfaces.
•
With the key on engine off (KOEO), verify vehicle
battery voltage is at least 8.0V.
•
Verify the control module is not defective.
6.2
Scan Tool Does Not Power Up
WARNING
Review "1.2
5 before troubleshooting.
If scan tool will not power up, communicate with vehicle
control module, pass scan tool self-tests, or functions
incorrectly in any other way, do the following:
•
Clean the DLC pins.
•
Disconnect and reconnect DLC making sure it is
connected correctly.
•
Check vehicle battery to make sure at least 8.0 volts
is present.
•
Contact customer service.
•
With the engine off, check for blown fuses in the
vehicle fuse box.
6.3
Vehicle Communication Fault
The vehicle's control module(s) enters into an unrecov-
erable state.
1.
Turn vehicle key to off position.
•
Wait 10 seconds.
•
Press
.
6.4
Operating Error or Erroneous Data
An Operating Error or Erroneous Data occurs if vehicle's
computer(s) stop(s) communicating with the scan tool.
1.
Make selection.
•
Use the
and
Safety Messages" on page
keys.
Bosch Automotive Service Solutions Inc.
Hide quick links:
Advertisement
Table of Contents
