Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Philips CCC 090AT
Summary of Contents for Philips CCC 090AT
- Page 1 Color TV built-in VCR Owner’s Manual CCC090AT CCC092AT...
- Page 2 Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product. So complete and return the Warranty Registration Card enclosed with your purchase at once.
-
Page 3: Introduction 3
U.S. registered mark. Using products with the E NERGY lowers utility bills. SmartClock and ShowGuard are trademarks of Philips Consumer Electronics. Copyright 2001 Philips Consumer Electronics. All rights reserved. • English or Spanish displays • High Quality (HQ) System • One-Touch Recording • Real-Time Counter •... -
Page 4: Table Of Contents
4 Table of Contents Setting Up Your TV/VCR Introduction ............3 Table of Contents . -
Page 5: Before Using The Tv/Vcr 5
Putting Batteries in the Remote Control Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then lifting off the lid. Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid. -
Page 6: Hooking Up The Tv/Vcr
6 Hooking Up the TV/VCR Connect an antenna or cable signal to your TV/VCR using one of the following connections. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). - Page 7 Hooking Up Your TV/VCR with the Supplied Rod Antenna To install the supplied rod antenna, push the base stem of the antenna into the antenna hole on the back of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown.
- Page 8 8 Hooking Up the TV/VCR (cont’d) Mobile Connections Usually, the supplied rod antenna provides adequate reception. But when you want to watch TV outdoors or in a vehicle, try a mobile antenna (not supplied) or an indoor dipole antenna (not supplied) for better reception.
-
Page 9: Turning On The Tv/Vcr 9
Before you turn on the TV/VCR, make sure batteries are in the remote control and you have connected the TV/VCR correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. Press the POWER button. The TV/VCR will come on and this screen will appear. -
Page 10: Automatic Channel Setup
10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following these steps. Press the MENU button. PRIM. SETUP PRESS >... - Page 11 Adding/Deleting Channels If your channel lineup changes, you may want to add newly avail- able channels or remove channels that are no longer available in your area. You can use the CH(annel) o o /p p buttons to scroll through only the available channels. To add or delete channels from the TV/VCR’s memory, follow these steps.
-
Page 12: Setting The Clock
12 Setting the Clock There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from a PBS station. - Page 13 Press the PLAY/o button or the STOP/p button to select SET MANUAL CLOCK, then press the F.FWD/B button. SET MANUAL CLOCK TIME – – : – – DATE – – / – – / – – – – TO END PRESS EXIT Press two Number buttons for the hour(s) and two Number buttons for the minute(s).
- Page 14 14 Setting the Clock (cont’d) Automatic PBS Channel Selection Press the MENU button. PRIM. SETUP > PRESS B VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP >...
-
Page 15: Helpful Hints
Press the PLAY/ button or the STOP/ SET PBS CH. AUTO. Then, press the F.FWD/B button. SET AUTO CLOCK TIME – – : – – DATE – – / – – / – – – – NOW SEARCHING TO END PRESS EXIT NOW SEARCHING flashes on the TV/VCR screen. - Page 16 16 Setting the Clock (cont’d) Manual PBS Channel Selection Press the MENU button. PRIM. SETUP > PRESS B VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP SELECT LANGUAGE >...
- Page 17 Press the PLAY/ button or the STOP/ SET PBS CH. MANUAL. Then, press the F.FWD/B button. AUTO CLOCK (PBS) CH 02 TIME – – : – – DATE – – / – – / – – – – SELECT CHANNEL NUMBER TO END PRESS EXIT Use the Number buttons to select your PBS station.
-
Page 18: Daylight-Savings Time
18 Daylight-Savings Time When the Daylight-Savings Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Savings Time ON or OFF, follow the steps below. Press the MENU button. -
Page 19: Time Zone 19
When you set the clock using AUTO CLOCK, specify your time zone. Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP >... -
Page 20: Language Selection
20 Language Selection Follow the steps below to change the language of the on-screen displays and menus. Press the MENU button. PRESS > PRIM. SETUP VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP >... -
Page 21: Front Panel 21
Cassette Compartment Insert a video cassette tape here. Wireless Remote Sensor Receives a signal from your remote control so you can operate the TV/VCR from a distance. REC(ord) Light This light appears during a recording. It flashes slowly when the TV/VCR power is off for a timer recording. -
Page 22: Remote Control Buttons
22 Remote Control Buttons CLEAR Button Press to erase incorrect data when programming TV/VCR func- tions. Also, press to reset the real-time counter to 0:00:00. Details are on page 41. POWER Button Press to turn on or off the TV/VCR. Number Buttons Use to select channels and to program TV/VCR functions (such as setting the clock). - Page 23 Remote Control Buttons (cont’d) 23 STATUS/EXIT Button Press to access or remove the status display. Details are on page 25. Press to remove the menu. EJECT Button Press to eject the tape. MENU Button Press to display the main menu. You also may use the buttons on the front panel of the TV/VCR to access the menu.
-
Page 24: Rear Panel
24 Rear Panel ANT(enna) Jack Connect your antenna or cable here. Details are on pages six-eight. DC 13.2V Jack Connect the car battery cord here. Details are on page eight. AC 120V Jack Connect the AC power cord here. Details are on page seven. Antenna Hole Connect the base stem of the supplied rod antenna here. -
Page 25: On-Screen Status Displays 25
A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: Whenever you press the STOP/p button or the PLAY/o but- ton, the status display will appear for five seconds. -
Page 26: Adjusting The Picture Controls
26 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. Press the MENU button. TO ADJUST PRESS { / B > BRIGHTNESS PICTURE COLOR TINT SHARPNESS TV RESET Press the PLAY/ button or the STOP/ the desired control (BRIGHTNESS, for example). -
Page 27: Adjusting The Picture Controls
BRIGHTNESS PICTURE COLOR TINT SHARPNESS Press the REW(ind)/{ button to decrease a picture control. Press the F.FWD/B button to increase a picture control. TO ADJUST PRESS { / B > BRIGHTNESS PICTURE COLOR TINT SHARPNESS TV RESET TO ADJUST PRESS{ / B BRIGHTNESS PICTURE COLOR... -
Page 28: Reminder
28 Reminder The channel number will remain on the screen during TV viewing when you set REMINDER to ON. Set REMINDER to ON or OFF by following these steps. Press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS... -
Page 29: Playing 29
Follow the steps below to play a tape. Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab is missing, playback should start automatically. If playback does not start automatically, press the PLAY/ button to start playback. Press the STOP/ button to stop playback. -
Page 30: Recording
30 Recording Read and follow the steps below to record a TV program. Place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button to turn on the TV/VCR, if necessary. -
Page 31: One-Touch Recording 31
A One-Touch Recording (OTR) is an immediate timed recording from 30 minutes to eight hours long. Before you begin, make sure: Channels are set. Details are on page 10. A tape is in the TV/VCR. The record tab must be intact. Use the CH(annel) o o /p p buttons or the Number buttons to select the channel you want to record. -
Page 32: Rerecording (Tape Duplication)
32 Rerecording (Tape Duplication) AUDIO and VIDEO OUT Jacks on source unit (VCR or Camcorder) Make the connections shown above, using audio and video cables (not supplied). Connect the source unit (VCR or camcorder) to a power source after connections are made. The source unit will play your tape. -
Page 33: Timer Recording 33
Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: The clock is set. If not, CLOCK MUST BE SET appears, fol- lowed by the SET CLOCK menu. - Page 34 34 Timer Recording (cont’d) Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not been stored yet). NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds.
- Page 35 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 30. You cannot use the SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON...
- Page 36 36 Timer Recording (cont’d) Checking or Clearing Timer Recordings With the TV/VCR on, press the MENU button. Press the PLAY/ button or the STOP/ VCR PROGRAM, then press the F.FWD/B button. Press the PLAY/ button or the STOP/ PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered position will appear on the screen.
-
Page 37: Defeat Recording 37
Follow these steps to prevent accidental recording. Press the MENU button. PRIM. SETUP PRESS > VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ VCR SETUP, then press the F.FWD/B button. VCR SETUP > ONE TIME PLAY [ON] REPEAT PLAY ON-SCREEN MODE... - Page 38 38 A-B Repeat Play Follow these steps to program the TV/VCR to play the material between two specified points (A and B) on a tape over and over again. Insert a tape in the TV/VCR. Press the MENU button. PRIM. SETUP PRESS >...
-
Page 39: A-B Repeat Play
Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. A-B REPEAT 0:12:34 Play, fast forward, or rewind the tape to the position at which you want to begin playback. -
Page 40: Repeat Play
40 Repeat Play Follow these steps to program the TV/VCR to play a tape over and over. Press the MENU button. PRESS > PRIM. SETUP VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS PICTURE Press the PLAY/ button or the STOP/ VCR SETUP, then press the F.FWD/B button. VCR SETUP ONE TIME PLAY [ON]... -
Page 41: Real-Time Counter Memory 41
Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. Press the STATUS/EXIT button. -
Page 42: Playback Options
42 Playback Options Forward and Reverse Searching (SP/LP/SLP) During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. To return to normal playback, press the PLAY/ Super High Speed Searching (LP/SLP) During tape playback, press the F.FWD/B button or the REW(ind)/{ button, then press again. -
Page 43: Blue Background 43
If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to OFF. When you select a channel that is receiving a weak signal, you will see and hear the static in the TV programming. -
Page 44: Sleep Timer
44 Sleep Timer Use the sleep timer to program the TV/VCR to shut off in a cer- tain amount of time. Press the SLEEP/WAKE UP button. TO ADJUST PRESS s s / B B –TIMER– SLEEP > WAKE UP ON-TIME Press the PLAY/o o button or the STOP/p p button to select SLEEP. -
Page 45: Wake Up Timer 45
The Wake Up Timer turns on the TV/VCR automatically at a speci- fied time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. -
Page 46: Volume Bar
46 Volume Bar Usually, the volume bar appears when you press the VOL(ume) o o /p p buttons. If you do not need it, set the VOLUME BAR to OFF. Press the MENU button. PRESS > PRIM. SETUP VCR PROGRAM VCR SETUP REMINDER BRIGHTNESS... -
Page 47: Automatic Operation Features 47
Automatic Operation Features 47 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. -
Page 48: Helpful Hints
48 Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before request- ing service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. -
Page 49: Helpful Hints
The remote control is not available, or the remote control will not access the menu. • Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 21. TV/VCR has no power. -
Page 50: Glossary
50 Glossary AUDIO In Jack: jack on the front of the TV/VCR which is used to record or receive audio from another source. Automatic Channel Setup: process in which the TV/VCR memorizes all available channels. Then, when you push the CH(annel) o/p buttons, you only scan through channels you receive. -
Page 51: Specifications 51
General CRT: 9-inch in line gun Television system: NTSC-M Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec. Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C) Relative Humidity: 10% to 75% Power requirement: AC 120V/DC 13.2V, 60Hz Power consumption: 55W (AC), 60W (DC) Sound output: 0.8W... -
Page 52: Limited Warranty
RENEWED 90 DAY LIMITED WARRANTY... -
Page 53: Index 53
a-b repeat play ..38-39 accessories ....56 ant(enna) jack ..6-8, 24 audio in jack . -
Page 54: Accessories
The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR. To order these optional accessories, contact us at: Philips Parts & Accessories Marketing Department 401 East Old Andrew Johnson Highway VHS Cassette Rewinder...