Page 5
System Information....................36 Return Material Request ..................37 Radio Products and Services Division..............37 5.4.1 Radio Products and Services Division Telephone Numbers........37 Returning System Components to Motorola ............37 Returning FREs .......................37 WARRANTY INFORMATION ................38 FCC REGULATORY INFORMATION ..............41 FCC Information ......................41 FCC RF Radiation Exposure Statement ..............41...
IP devices via a built-in RJ45 Ethernet port. Both the EWR and the PWR efficiently combine the functionality of a Motorola Wireless Router and client modem into a single cost-effective wireless network component. This makes it easy for any Ethernet-ready device to access a Mesh Enabled Architecture (MEA), mobile broadband network.
Geo-Location, and the capability of enabling IP devices. The EWR6300 comes with a mounting bracket that can be attached to a pole with a diameter of 1-3.5 inches. For correct MEA deployment, a power source for each EWR must be provided.
Mesh Enabled Architecture EWR/PWR Users Guide Equipment Requirements An EWR6300 and a PWR6300 are utilized similarly to a subscriber device within a MEA network. Both will be used with the following Motorola’ infrastructure devices: IAP6300 and MWR6300. 2.3.1 EWR6300 The following list defines the standard MEA hardware components needed to set up a EWR: •...
Page 12
The Network Operator must supply the following: • Mounting Location • Power Source (12 VDC) • Hand tools for bracket installation Optional Equipment: • An Antenna Cable and connector Antenna Options are the following Manufacturer Part Number Gain Usage Maxrad BMMG2400ML195MSMA 0 dBi Mobile...
MAC Address Label Location 2.4.1 EWR The transceiver Media Access Control (MAC) address and the Ethernet MAC address is typically listed on a label located on the antenna end of the EWR6300. A sample label is shown Figure 2-1. Record the transceiver MAC Address and Ethernet MAC Address in the MAC Address Table below, as they will be required later to configure and test the device.
Page 14
addresses will be required later in the configuration and management process. Write the MAC numbers into the MAC Address Table provided below. MAC Address Table MAC Address (00-05-12-0A-xx-yy) ETH MAC Address (00-05-12-30-xx-yy)
5. The Test Port is unused during deployment. 2.5.3 EWR6300 Mounting Bracket The EWR6300 mounting bracket is identical to the mounting bracket for the IAP6300 and the MWR6300. The bracket is robust secure; and can be used for horizontal, vertical, and off-angle pole mounted installations.
Figure 2-4. EWR6300 Mounting Bracket Using the deployment guidelines described in the MEA Setup and Deployment User’s Guide, locate an appropriate mounting pole such at a streetlight cobra arm or a metal post. The mounting pole can be vertical, horizontal, or project at almost any angle.
Mesh Enabled Architecture EWR/PWR Users Guide 3 1/2 x 1/4 inch bolt 1/4 Flat Washer 1/4 Flat Washer 1/4 Lock Washer 1/4 Hex Nut Note: All Hardware is Stainless Steel Figure 2-5. C-Clamp Bracket Assembly 3. Position the bracket in the desired location and securely tighten the two bracket bolts. 4.
6 x 32 x 3/4 Angle Locking Bolt 1/4 x 1 inch Pivot Bolt (Requres 7/16 Wrench) Figure 2-6. EWR Pivot and Angle Locking Bolts NOTE: Some IAP6300 and MWR6300 enclosures may have a bolt or plug in the center of the back of the box.
Figure 2-8 PWR6300 Cabinet Mounting Device Deployment Considerations When deploying the EWR6300 or the PWR6300 consider the following: • The antenna should be a minimum of 30 inches from any nearby metal poles to avoid distortion of the RF pattern.
- Mount the supplied antenna vertically Testing the Device Installation Verify the operation of each installed EWR6300 and PWR device using the following procedure: 1. Apply power to the EWR6300 or the PWR6300, as applicable. (On the PWR device, the power reset button will be illuminated to red.) 2.
Mesh Enabled Architecture EWR/PWR Users Guide 3 Device Configuration The Device Configuration information provided in this section applies to both the EWR and the PWR devices due to their functional similarities. It is important to note that within the MeshManager Software and the Device Administration Web interface, any reference made to a EWR device is also applicable to a PWR.
the access account may be used for monitoring the status of the device. The installation procedure described here requires Administrator access. Alternatively, all of the parameters that are provisioned via the web page may be provisioned via MeshManager instead. The password for the admin account should be changed during installation. The Access or Normal User account password can be changed by the Administrator.
Mesh Enabled Architecture EWR/PWR Users Guide 3.2.2 Viewing MEA Redirecting Page After the login authentication has been completed, the web browser will display a redirecting page, and your browser will automatically transition to the home web page for MEA Device Administration.
3.2.3 Viewing MEA Device Administration Home Page When logging in with the Administrator Account, or Super User, the MEA Device Administration home page provides basic information about the device, including the IP addresses assigned to the device, the MAC addresses of the device, the firmware revision number, and the reported link quality for the link to the IAP.
3.2.4 Viewing the EWR Device Administration Configuration Tab When logged in as an Administrator role, the EWR Device Administration (Super User Login) Configuration page allows for changes to the configuration of EWR and PWR devices. Figure 3-5. EWR (PWR) Device Configuration Page (Super User Login) The fields displayed on this page are described in the following table.
Mesh Enabled Architecture EWR/PWR Users Guide EWR (PWR) Device Administration (Super User Login) Page Fields Field Name Field Description Field Default Value System Name This is the name of the device as shown by Assigned by MeshManager Network Administrator RDATE Server IP The IP address of the RDATE server.
tab that can be edited by the Normal User. In the Geo Reference section, Latitude, Longitude and Altitude information may be entered, if known. Due to the stationary nature of a EWR or a PWR device, the information provided in the Geo Reference section can be used for gathering other Subscriber Device geo-location information when used in conjunction with the Mesh Positioning Application software.
Mesh Enabled Architecture EWR/PWR Users Guide Device Addressing Schemes The concept of unified modes of operation centers on the current state of network communication: Associated State and Unassociated State. There are three addressing schemes which allow the network manager increased flexibility in deployment: Network DHCP, Statically Provisioned, and User Supplied.
This scheme is ideal for a managed network of users who regularly need to communicate inside and outside of network coverage or for a network lacking a DHCP server. 3.3.3 User Supplied Scheme Operating under the User Supplied scheme, the EWR device is configured to use a fixed IP address and subnet mask.
Mesh Enabled Architecture EWR/PWR Users Guide Figure 3-8. System Update Save Completed Web Page After the settings have been saved, click the Finished button. The web browser should return to the MEA Device Administration home page. A reboot of the device is not required for the changes to take effect.
External Device Provisioning The External Device Provisioning section of the EWR Device Administration page is used to configure addresses for the attached nodes on the local Ethernet segment. Up to three addresses are provisioned. Figure 3-9. External Device Provisioning Table The Enable checkbox indicates this row contains a valid address.
Mesh Enabled Architecture EWR/PWR Users Guide reserved for a specific device. The reserved checkbox must be marked for this kind of IP address reservation. The Status field indicates whether the provisioned IP address was detected (via a ping) when the web page was brought up. The IP addresses default to values based on the transceiver MAC address of the device.
4 Device Maintenance Resetting the EWR via the Device Administration Web Page Although you should not have to reset the EWR/PWR device, the device can be commanded to reset via the web pages. In order to reset the device, return to the MEA Device Administration home page, and click on the Reset the Device link in the Device Management panel.
Mesh Enabled Architecture EWR/PWR Users Guide Figure 4-2. Device Reset in Progress Page NOTE: After the completion of the reset, you may experience a significant delay when bringing up another web page. Please be patient.
Restoring Factory Settings – User Supplied Mode Limitations NOTE: In Release 3 and 3.1, there is a known issue that arises if the selected device addressing mode is User-Supplied when the user restores the factory default settings for the EWR/PWR. The following options are offered as a way to recover from this limitation.
Mesh Enabled Architecture EWR/PWR Users Guide Restoring Factory Settings – Normal Operations When the Restore Factory Defaults function is selected from the EWR Device Administration Home Page, the device will present the following web page. Figure 4-3. Restore Factory Settings Web Page The Restore Factory Defaults function allows the operator to return the device to factory defaults.
Figure 4-4. Confirm Changes Window for Restore Factory Settings The Factory Settings Restored page will be displayed. Figure 4-5. Factory Settings Restored Web Page Click on the Finished button to complete the reset procedure.
Mesh Enabled Architecture EWR/PWR Users Guide Changing the Web Interface Password When the Change Admin Password function is selected from the EWR Device Administration Home Page by the administrator, or the Change User Password function is selected, the device will present the following web page: Figure 4-6.
When the operator confirms the change, the new password will be stored in flash, and the device will present a status screen indicating that the change was successful. Figure 4-8. Password Changed Confirmation Web Page...
Mesh Enabled Architecture EWR/PWR Users Guide Security Provisioning Web Page When the Security Provisioning option is selected from the EWR Device Administration Home Page by the administrator, the device will present the following web page: Figure 4-9. Security Provisioning Web Page The Security Provisioning web page contains two main sections: Provision Username and Provision Groupname.
Upgrading the Device Firmware The web interface for the device also provides the ability to upgrade the firmware on-site. To use this feature, you must have an upgrade file from a released upgrade package. When the Upgrade Device Firmware function is selected from the MEA Device Administration Home Page, the device will present the following web page: Figure 4-10.
Page 43
Mesh Enabled Architecture EWR/PWR Users Guide Figure 4-11. Confirm Upload Window for Firmware Update Once the filename has been confirmed, the web browser will transmit the file to the device, and the device will present an upgrade progress screen. This page will indicate the current stage in the upgrade process.
Motorola System Support Center (SSC). When you consult the Motorola SSC, you increase the likelihood that problems are rectified in a timely fashion and that warranty requirements are satisfied. Check your contract for specific warranty and service information.
Motorola's service philosophy is based on field replaceable entities (FREs). FREs are system components identified by Motorola to be returned to Motorola for repair. In turn, Motorola sends you a replacement FRE component to help you maintain maximum operating performance for your system.
One (1) Year from the date of shipment. Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it with the same or equivalent Product (using new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided purchaser notifies Motorola according to the terms of this warranty.
Page 47
A) that Motorola will be notified promptly in writing by such purchaser of any notice of such claim; B) that Motorola will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and...
Page 48
Motorola which is attached to or used in connection with the Product. The foregoing states the entire liability of Motorola with respect to infringement of patents by the Product or any its parts thereof.
(1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. The EWR6300 (Enhanced Wireless Router) is an infrastructure device that is positioned at a fixed location such as a pole, wall, or rooftop. The EWR6300 requires professional installation to ensure that the installation is performed in accordance with FCC licensing regulations.
(RF) electromagnetic energy emitted by FCC certified equipment. Motorola’ MEA products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio according to the instructions found in this manual and the hardware and software guides on the MEA CD will result in user exposure that is substantially below the FCC recommended limits.
European community. It proves to the buyer or user that this product fulfills all essential safety and environmental requirements as they are defined in the European Directives. Motorola Products are covered under the following product certification Europe: ETSI EN 300 328 V 141 (2003-04) ETSI EN 301 489-1 (2002-08) and 301 489-17 EN 55022:1998 and EN 55024:1998 CENELEC EN 50360 and EN50371 –...
Page 52
Alert CE Mark Symbol The alert symbol indicates that Motorola products are not certified to operate in France. Outdoor use in France is restricted to 10mW EIRP for band 2454 – 2483.5 MHz.