Philips BDL3245E/00 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Monitor
  5. BDL3245E/00
  6. Service manual

Philips BDL3245E/00 Service Manual

32''&42''&46'' flat wide monitor
Hide thumbs Also See for BDL3245E/00:
Table of Contents

Advertisement

Quick Links

See also: User Manual
32"&42"&46" Flat Wide Monitor
Service
Service
Service
Table of Contents.........................................................1
Revision List................................................................2
Safety Instructions....................................................3
1. General Specifications...............................................7
2. Flat Wide Monitor Description................................13
3. Operation Instructions..............................................15
3.1 Control Panel................................................15
3.2 Input/ Output Terminal ...........................................16
3.3 Remote Control..............................................17
3.4 OSD Menu...................................................18
4. Input/output Specification.......................................28
4.1 Input Signal Connector.........................................28
4.2 Factory Preset Display Modes................................30
4.3 Pixel Defect Policy..........................................21
4.4 Failure Mode of Panel .....................................34
5. Block Diagram..........................................................35
5.1 Scaler Board..........................................................35
5.2 Power Board..........................................................36
6. Schematic Diagram..................................................37
6.1 Scaler Board...............................................37
6.2 Power Board..........................................................53
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2011 Philips Consumer Lifestyle
BDL3245E/00
BDL4245E/00
BDL4645E/00
Page Description
6.3 Connection Board...........................................61
6.4 IR Board..........................................................63
6.5 Key Board......................................................64
6.6 CNPC Board...................................................64
7. PCB Layout......................................................65
7.1 Scaler Board...................................................65
7.2 Power Board...................................................66
7.3 Connection Board...........................................70
7.4 IR Board.........................................................71
7.5 Key Board......................................................71
8. Wiring Diagram.................................................72
9. Scaler Board Overview.......................................74
10. Mechanical Instructions.....................................75
11. Trouble Shooting.............................................85
12. ISP Instructions.........................................................87
13. DDC Instructions.....................................................102
15. Monitor Exploded View...........................................138
16. Recommended & Spare Parts List.........................141
17.General Product Specification.............................144
SAFETY NOTICE
Subject to modification ○
K
Nov.11, 2011
Page

Advertisement

Table of Contents
loading

Related Manuals for Philips BDL3245E/00

Summary of Contents for Philips BDL3245E/00

  • Page 1: Table Of Contents

    CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2011 Philips Consumer Lifestyle Subject to modification ○ Nov.11, 2011...

  • Page 2: Revision List

    Revision List Version Release Date Revision History Nov.11,2011 Initial release, Draft Version Nov.23,2011 Add CTN models BDL3245E/00 and BDL4645E/00...

  • Page 3: Safety Instructions

    Safety Instructions Warnings and Precautions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

  • Page 4: Regulatory Information

     Keep the monitor out of direct sunlight and away from stoves or any other heat source.  Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.  Do not block the ventilation holes on the cabinet. ...
  • Page 5 se only RF s shielded cabl e that was s upplied with the monitor when conne cting this mo onitor to a co omputer devic o prevent da mage which may result i n fire or shoc ck hazard, do o not expose e this applian nce to rain or...
  • Page 6 Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer. For Customers in Canada and USA This product may contain lead and/or mercury.

  • Page 7: General Specifications

    1. General Specifications BDL3245E Display Item Specifications Screen Size (Active Area) 32" LCD Aspect ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.36375 (H) x 0.36375 (V) [mm] Displayable colors 1.06B colors Brightness (typical) 500 cd/m2 Contrast ratio (typical) 1450:1 Viewing angle...
  • Page 8 General Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 160W Power Consumption (typ.) 140W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 773.6 x 505.1 x 239.8 mm Dimensions (Without Stand) [W x H x D] 773.6 x 468.3 x 116 mm Weight (With Stand)
  • Page 9 BDL4245E Display Item Specifications Screen Size (Active Area) 42" LCD Aspect ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.4845 (H) x 0.4845 (V) [mm] Displayable colors 16.7M colors Brightness (typical) 450 cd/m2 Contrast ratio (typical) 4000:1 Viewing angle 178 degrees...
  • Page 10 General Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 260W Power Consumption (typ.) 210W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 991.6 x 621 x 329.6 mm Dimensions (Without Stand) [W x H x D] 991.6 x 584 x 115.5 mm Weight (With Stand)
  • Page 11 BDL4645E Display Item Specifications Screen Size (Active Area) 46" LCD Aspect ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.5302 (H) x 0.53025 (V) [mm] Displayable colors 16.7M colors Brightness (typical) 400 cd/m2 Contrast ratio (typical) 4000:1 Viewing angle 178 degrees...
  • Page 12 General Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 270W Power Consumption (typ.) 220W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 1091.1 x 681.7 x 329.6 mm Dimensions (Without Stand) [W x H x D] 1091.1 x 645.7 x 133 mm Weight (With Stand)

  • Page 13: Flat Wide Monitor Description

    2. Flat Wide Monitor Description BDL3245E The Flat Wide monitor will contain a scaler board, a power board, two CNPC boards, an IR board and a key board. The scaler board houses the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the scaler board chips each voltage.
  • Page 14 BDL4245E & BDL4645E The Flat Wide monitor will contain a scaler board, a power board, a connection board, a CNPC board, an IR board and a key board. The scaler board houses the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the scaler board chips each voltage.

  • Page 15: Operating Instructions

    3. Operating Instructions 3.1 Control Panel to activate the OSD menu when the OSD menu is 1. POWER Button Use this button to turn the display on or put the off. display to standby. Note: 2. Mute Button Keyboard Control Lock Mode: This function Switch the audio mute ON/OFF.

  • Page 16: Input/ Output Terminal

    3.2 Input/ Output Terminal 1. MAIN POWER SWITCH external AV device. Press to switch the main power on/off. 10. AUDIO IN 1,2,3 2. AC IN Connect audio input from external AV device. Connect the supplied power cord to the wall outlet. ...

  • Page 17: Remote Control

    3.3 Remote Control [ON/OFF]: Turn PIP mode ON/OFF. [INPUT]: Select the input signal for the sub picture. [CHANGE]: Toggle between the main picture and sub picture. 4. [CONTRAST] Button: Press to activate Contrast Menu. Press the [+] or [-] button to adjust the value. Press [MENU] button to confirm and exit.

  • Page 18: Osd Men

    • Press to increase the value in OSD menu. 13. [BRIGHTNESS] Button Press to toggle Brightness Menu. Press the [+] or [-] • Press to move the sub picture right in PIP mode button to adjust the value. Press [MENU] button to 17.
  • Page 19 Contrast Smart contrast Adjust to sharpen the picture quality. The black When turned on, this function helps enhance image portions of the picture become richer in darkness and contrast when displaying dark scenes. the white become brighter. Smart picture Sharpness The following smart picture modes are available for: Adjust to improve the image detail.
  • Page 20 Zoom mode 21:9The picture is The pictures you receive may be transmitted in 16:9 enlarged to 16:9 format. format (wide screen) or 4:3 format (conventional This mode is screen). The 16:9 pictures sometimes have a black recommended when band at the top and bottom of the screen (letterbox displaying pictures that format).

  • Page 21: Audio Menu

    Audio Menu PIP Menu Balance Adjust to emphasize left or right audio output balance. Select the PIP (Picture-in-Picture) mode. The options are: {Off} / {PIP} / {POP} / {PBP aspect} / Treble {PBP full}. Adjust to increase or decrease higher-pitched sounds. PIP input Bass Select the input signal for the sub-picture.

  • Page 22: Configuration1 Menu

    Configuration1 Menu the risk of the “image persistence”.  {Cooling Fan} - Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the display’s temperature. NOTES: - The default {Auto} option will start running the cooling fan if the temperature of 65°C (152°F) is reached, and will keep running for 30 minutes after cooling down to the temperature of 62°C...
  • Page 23 Configuration2 Menu OSD turn off  DHCP - Choose to enable or disable the DHCP Set the period of time the OSD menu stays on the function. If enabled, the display will be assigned IP screen. The options are: {5 ~ 120} seconds. address, Subnet mask and Default gateway Information OSD automatically.

  • Page 24: Advanced Option Menu

    Advanced Option Menu NOTE: This item is for HDMI-Video timing, DVI-D (HD timing), DP (HD timing), and YPbPr inputs only. Scan conversion Choose to enable or disable the IP (Interlace to Progressive) conversion function.  {Progressive} - Enable the IP conversion function (recommended).
  • Page 25  Frame comp. - Choose to turn the frame Keyboard control Choose to enable or disable the display keyboard compensation function on or off. If turned on, the (control buttons) function. display will adjust the image to compensate for the ...
  • Page 26 Date and time Adjust the current date and time for the display’s internal clock. 2. Press [▲] or [▼] button to select a schedule item (item number 1 ~ 7), and then press [+] button to mark it the item number. 1.
  • Page 27 NOTES: Auto signal detection  The {Every day} selection in a schedule item takes Choose to let the display detect and display available priority over the other weekly schedules. signal sources automatically.  If the schedule overlaps, the scheduled power-on ...

  • Page 28: Input/Output Specification

    4. Input/ Output Specification 4.1 Input Signal Connector 1. VGA Pin No. Name Pin No. Name Red video Green video Blue video Red GND Green GND Blue GND +5V (Supply from PC for DDC circuit) Sync GND DDC serial data H-sync V-sync DDC serial clock...
  • Page 29 4. RS-232C Input /Output DB-25 D-sub-9 Signal Direction Signal Name Protective Ground DTE-to-DCE Transmitted Data DCE-to-DTE Received Data DTE-to-DCE Request To Send DCE-to-DTE Clear To Send DCE-to-DTE Data Set Ready Signal Ground DCE-to-DTE Received Line Signal Detector (Carrier Detect) DTE-to-DCE Data Terminal Ready DCE-to-DTE Ring Indicator...

  • Page 30: Factory Preset Display Modes

    4.2 Factory Preset Modes VGA Resolution: Standard Active Resolution Refresh Rate Pixel Rate Aspect Ratio Stand for Mode Resolution (Hz) (MHz) H pixels V Lines 25.175 31.5 Video Graphic Array 31.5 WVGA 33.75 16:9 Wide Video Graphic Array SVGA Super VGA 49.5 1024 Extend Graphic Array...

  • Page 31: Pixel Defect Policy

    Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with your local guarantee conditions.
  • Page 32 Types of Pixel Defects + Dot Definition Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within each category. Bright Dot Defects = what is a defective “Dot”? One or more defective, adjacent sub-pixel is defined as one “dot”.
  • Page 33 Pixel Defect Tolerances In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.

  • Page 34: Failure Mode Of Panel

    4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. Phenomenon Failure description Vertical block defect...

  • Page 35: Block Diagram

    5. Block Diagram 5.1 Scaler Board...

  • Page 36: Power Board

    Power Board BDL3245E AC Input EMI Filter +24V To Backlight and PFC Converter audio amplifier Bridge Rectifier Main Power ICE2PCS02H D15XB80 L6599DTR +12V To LVDS PS_ON AUX Converter To MCU and A6069H Scaler Board BDL4245E &BDL4645E AC Input EMI Filter +24V To Backlight and PFC Converter...

  • Page 37: Schematic Diagram

    6. Schematic 6.1 Scaler Board ( 715G5049M0E000005F) Remark: Parts position can be searched by using FIND function in PDF. HDMI+VGA INCONNECTOR CN100 HIN_RX2P A-RED+ HIN_RX2P A-GREEN+ D2 Shield HIN_RX2M A-BLUE+ R128 HIN_RX2M HIN_RX1P 0R05 1/16W HIN_RX1P VGA_Pin5 D1 Shield VGA_Det HIN_RX1M A-RED- HIN_RX1M...
  • Page 38 Remark: Parts position can be searched by using FIND function in PDF. R6108 HD_BY PASS 10K 1/16W 5% DVI IN+ VGA OUT R6109 C6102 10K 1/16W 5% 100N 16V CONNECTOR CN502 ACVBS_OUT U612 ACVBS_IN C6094 0.1uF50V ACVBS_IN 7 C163 100UF 16V ACVBS_OUT CVBS OUT CVBS IN...
  • Page 39 Remark: Parts position can be searched by using FIND function in PDF. DIN_RX2P DIN_RX2P 3 DIN_RX2M DIN_RX2M 3 DIN_RX1P DIN_RX1P 3 DIN_RX1M DIN_RX1M 3 +3.3V_HSW DIN_RX0P +5V_SY NC_DEC DIN_RX0P 3 DIN_RX0M U4172 DIN_RX0M 3 2,5,7,15 +5V_SY NC_DEC VOUT DIN_RXCP DIN_RXCP 3 DIN_RXCM DIN_RXCM 3 DIN_HP_CTRL...
  • Page 40 Remark: Parts position can be searched by using FIND function in PDF. YPbPr IN component side CN406 R/Pr B/Pb FB105 BNC_G_Y 60 OHM R126 0R05 1/16W BNC_G_Y 7 FB107 20101217 60 OHM R152 0R05 1/16W BNC_B_Pb BNC_B_Pb 7 FB109 BNC_R_Pr 60 OHM R160 0R05 1/16W...
  • Page 41 Remark: Parts position can be searched by using FIND function in PDF. CONN CN104 MCU5V 9,12,15,16 OPS_TX2P OPS_TX2P MCU5V OPS_TX2M OPS_TX2M PWR_TH_CTL PWR_TH_CTL 16 OPS_TX1P 20110810 OPS_TX1P OPS_TX1M OPS_TX1M OPS_PWR FB103 OPS_PWR 15 OPS_TX0P 300OHM 4A C127 OPS_TX0P OPS_TX0M 0.47UF 50V OPS_TX0M R112 18K 1/10W...
  • Page 42 Remark: Parts position can be searched by using FIND function in PDF. +1.2V_ADC +3.3V_ADC +3.3V_ADC +1.2V_ADC 15 FB121 FB6008 120 OHM 300OHM 4A C4239 0.47UF 50V R4289 18K 1/10W AAUD1IN_L C177 C178 C175 C179 C180 AAUD1IN_L 10 CN409 C176 U401B AAUD1IN_R 2U2 16V 100N 16V...
  • Page 43 Remark: Parts position can be searched by using FIND function in PDF. +3.3V_HDMI +3.3V_HDMI C4208 C4209 C4210 C4211 C4212 2U2 16V 100N 16V 100N 16V 100N 16V 100N 16V +1.2V_HDMI +3.3V_HDMI +1.2V_HDMI 15 C4216 U401D 100N 16V STDP8028-AB U401C HDMI_BRX2P STDP8028-AB HDMI_BRX2N HDMI_BRX1P...
  • Page 44 Remark: Parts position can be searched by using FIND function in PDF. +3.3V_I/O +1.2V_LPM +3.3V_LPM PSU_EN +3.3V_I/O 13,15 +1.2V_LPM R4235 +3.3V_LPM MSTR0_SDA +5V_MAIN_En R4256 13,15 +3.3V_LPM R736 NC/5K6 1/16W 5% MCU5V +3.3V_I/O 6,13,15 +3.3V_I/O MSTR0_SCL R4257 C4219 C4220 C4217 C4221 C4218 2U2 16V 100N 16V...
  • Page 45 Remark: Parts position can be searched by using FIND function in PDF. +3.3V_AUD FB125 300OHM 4A C4257 0.47UF 50V AUD_IN3_L AAUD3IN_L R4299 18K 1/10W +3.3V_AUD AUD_IN2_L AAUD2IN_L +3.3V_AUD_FB +3.3V_AUD R4300 FB124 600 OHM FB126 18K 1/10W C4258 300OHM 4A R4301 R4302 C4260 0.47UF 50V...
  • Page 46 Remark: Parts position can be searched by using FIND function in PDF. +1.8V_DDR +1.8V_DDR +0.9V_DDR_VREF +1.8V_DDR C426 +0.9V_DDR_VREF 15 C4296 C4297 C4298 C4299 C4300 C4301 C4302 C4303 C4282 C4281 C4280 C4283 C4284 C4285 C4286 C4287 C4288 100N 16V C429 +0.9V_DDR_VREF 10uF 16V C438 C427...
  • Page 47 Remark: Parts position can be searched by using FIND function in PDF. Option for Panel-Tcon +3.3V_LVDS +3.3V_LVDS +3.3V_LVDS R4344 0R05 1/16W CONNECTOR for U401E C4336 C4337 C4338 PANEL-TCON STDP8028-AB 100N 16V 100N 16V 2U2 16V R4346 NC/0R05 1/16W CN416 AA18 RXA0+ LVDS_O_CH0P RXA0-...
  • Page 48 Remark: Parts position can be searched by using FIND function in PDF. +1.2V_CORE FB138 +1.2V_CORE_MARS +1.2V_CORE 120 OHM C4342 C4343 C4344 C4345 C4346 C4347 C4348 C4349 C4350 C4351 C4352 C4353 C4354 C4355 10uF 16V 100N 16V 100N 16V 100N 16V 100N 16V 100N 16V 100N 16V...
  • Page 49 Remark: Parts position can be searched by using FIND function in PDF. MODEL U603 +3.3V_AUD_AMP V422 V462 Q6002 OUT_MUTE V551 MMBT3906 R6025 V651 4K7 1/16W 5% 056G616 101 R6027 10K 1/16W 5% LOUT+ L6001 22UH +3.3V_AUD_AMP C6016 100N 25V C6017 100N 25V DGND R6007...
  • Page 50 Remark: Parts position can be searched by using FIND function in PDF. +12V +24V 120 OHM MCU5V MCU5V Wire Color FB181 +12V 9,12,16 +24V 9,14,16 MCU5V 6,9,12,16 +5V: RED CN413 C4370 C501 CONN C4371 C502 C4372 C500 100NF NC/0.1UF50V 0.1UF50V 330UF 35V 100uF 25V +12V: YELLOW...
  • Page 51 Remark: Parts position can be searched by using FIND function in PDF. MCU5V +5V_RTC +5V_RTC FB160 Q118 +5V_RTC 300OHM MMBT3906 C407 C416 R4391 C418 22pF 50V 100N 16V C417 560OHM +-5% 1/10W 100N 16V R4379 2U2 16V 10K 1/16W 5% +5V_RTC X402 R4405...
  • Page 52 Remark: Parts position can be searched by using FIND function in PDF. LAN0_TXD UART0_TXD LAN0_TXD LAN0_RXD R6006 33R 1/16W 5% UART0_RXD LAN0_RXD Power and by-pass capacitors R744 33R 1/16W 5% LAN1_TXD UART1_TXD LAN1_TXD LAN1_RXD UART1_RXD R6020 33R 1/16W 5% LAN1_RXD DVDD3.3V R6021 33R 1/16W 5%...

  • Page 53: Power Board

    6.2 Power Board BDL3245E (715G5082P01000003H) Remark: Parts position can be searched by using FIND function in PDF. F901 SG902 6.3A 250V R901 C9901 C991 390K 1/4W 220pF 250V 220pF 250V BD901 D15XB80 CN901 L901 IC911 20.0MH RV901 RV902 C993 Varistor 0.47uF C994 0.47uF...
  • Page 54 Remark: Parts position can be searched by using FIND function in PDF. L906 R997 D906 D922 FB902 NC(600uH) 10 OHM 5W 1N5408-E3/73 1N5408-E(Short pin) BEAD D907 NR902 C924 FMXA-1106S NTCR C925 1uF/450V L908 FB903 C922 1000pF C923 600uH 5% BEAD 180UF 450V NC(150uF 450V) C926...
  • Page 55 Remark: Parts position can be searched by using FIND function in PDF. R954 0.47 OHM +-5% 1W T902 POWER X'FMR C940 C939 R955 R956 10NF 100K 100K 2.2NF R957 R958 D909 47 OHM 1/4W 47 OHM 1/4W 1N4007-E3/73 C942 2200pF 500V C941 R959 100K...
  • Page 56 Remark: Parts position can be searched by using FIND function in PDF. R904 0.1 ohm T901 R910 POWER X'FMR 2M 1/4W R905 R906 R907 R908 R909 D902 D901 BO_DC LL4148 Q901 FMWN-2308 R911 TK15A60U 2M 1/4W L904 R9101 3.0uH 0R05OHM1/8W D927 R912 R914...
  • Page 57 BDL4245E & BDL4645E (715G4390P02W30003H) Remark: Parts position can be searched by using FIND function in PDF. BD_OUT+ BD902 L9904 3.5uH D15XB60 SG9901 R9901 L9903 390K +-5% 1/4W 10MH C9901 F901 220pF +-10% BD_OUT+ FUSE 8A 250V C9904 CN901 C9903 L9901 L9902 220pF +-10% 470NF...
  • Page 58 Remark: Parts position can be searched by using FIND function in PDF. BD_OUT+ D9801 D9802 1N5408-E3/73 1N5408-E3/73 FB9801 0.47UF 50V C9817 BEAD D9805 R9803 D9803 R9804 FMN-1106S L9801 D9806 C9816 175uH FMN-1106S 10NF 4.7 OHM +-5% 1/4W C9814 C9815 Q9803 150uF 450V 150uF 450V R9805...
  • Page 59 Remark: Parts position can be searched by using FIND function in PDF. R9301 0.47 OHM +-5% 1W T901 POWER X'FMR R9309 R9311 R9315 R9317 100K 1/4W 100K 1/4W 47 OHM 1/4W 47 OHM 1/4W AC_N C9301 C9303 10NF D9301 C9312 C9313 C9304 R9318...
  • Page 60 Remark: Parts position can be searched by using FIND function in PDF. CN908 CONN Q9109 T9101 PMBS3906 POWER X'FMR R9102 R9101 D9105 CN902 0.1 ohm FMWN-2308 BO_DC +24V D9101 2M OHM 1% Q9101 SCS0520P R9104 R9103 TK15A60U 2M OHM 1% 2M OHM 1% R9106 12V_D1...

  • Page 61: Connection Board

    6.3 Connection Board (715G5107T0D000005I) Only for BDL4245E & BDL4645E Remark: Parts position can be searched by using FIND function in PDF. TX24-80R-LT-H1E CONN CN1001 DDC+5V +16V CN1002 F_OPS_TX2P MCU5V F_OPS_TX2M OPS_OSD_STA PWR_TH_CON OPS_COM_DIR F_OPS_TX1P F_OPS_TX1M +24V F_OPS_TX0P F_OPS_TX0M PWR_TH F_OPS_TXCKP HT2_CTL SY S_FAN CN1005...
  • Page 62 Remark: Parts position can be searched by using FIND function in PDF. +24V IF_5V R1012 U1003 L78L05ACZ 51 OHM 1/4W L78LOO F1001 FUSE VOUT C1003 C1004 C1005 R1017 1uF 50V 4.7K 1/4W C1018 470uF 35V 470uF 35V 1uF 50V IF_5V ZD1001 SR36 R1007...

  • Page 63: Ir Board

    6.4 IR Board (715G5112R0C000004S) Remark: Parts position can be searched by using FIND function in PDF. VMCU_IR VMCU_IR CN201 CONN R202 R201 100R 1/10W 1% U201 VOUT IR_OUT LEDR C201 C202 ZD201 LEDG VMCU_IR ZD202 KSM-403M RLZ5.6B IR_OUT LEDG LEDR LED201...

  • Page 64: Key Board

    6.5 Key Board (715G4719K01000004K) Remark: Parts position can be searched by using FIND function in PDF. CN001 KEY _PWR R001 R002 R003 KEY _ADC1 KEY _ADC2 330R +-1% 1/10W 680R 1/10W 1% 2Kohm 1/10W +/-1% 330R +-1% 1/10W 680R 1/10W 1% 2Kohm 1/10W +/-1% CONN R004...

  • Page 65: Pcb Layout

    7. PCB Layout 7.1 Scaler Board (715G5049M0E000005F) Remark: parts position can be searched by using FIND function in PDF. R493 CN422 CN416 CN405 CN415 CN413 CN402 CN414 CN104 CN407 U445 C473 C4339 C4370 C500 Q129 C102 C125 C4373 R4366 C122 FB104 R113 Q120...

  • Page 66: Power Board

    7.2 Power Board BDL3245E (715G5082P01000003H) Remark: Parts position can be searched by using FIND function in PDF. GND3 GND4 C933 J910 D907 Q903 Q909 C936 J934 D903 D901 IC902 J914 J925 J923 J924 J928 C972 J930 C910 J922 C902 C971 FB909 J913 C927...
  • Page 67 Remark: Parts position can be searched by using FIND function in PDF. R9805 Q9803 R9804 R9803 R9802 Q9801 R939 R943 R944 R912 R911 R910 JR905 Q9802 R990 R933 R991 C973 C954 R931 C907 R999 R947 R918 C919 R926 R948 R928 R929 D908 R932...
  • Page 68 BDL4245E & BDL4645E (715G4390P02W30003H) Remark: Parts position can be searched by using FIND function in PDF. GND1 C9112 C9102 IC9102 HS15 J900 D9103 C9110 C9129 C9108 D9110 C9109 J907 C9815 C9814 C9120 T9101 L9101 C9121 J912 J905 HS14 J903 C9816 J910 R9101 J942...
  • Page 69 Remark: Parts position can be searched by using FIND function in PDF. Q9108 D9104 R9120 C9115 R9121 Q9109 R9124 R9126 R9118 R9116 C9103 R9123 C9114 R9122 C9113 R9125 R9117 C9107 R9115 C9133 C9111 C9104 C9105 C9106 C9130 R9136 C9123 D9102 D9101 Q9807 R9135...

  • Page 70: Connection Board

    7.3 Connection Board (715G5107T0D000005I) Remark: Parts position can be searched by using FIND function in PDF. CN1003 R1018 C1025 R1028 R1027 C1008 C1007 C1011 L1001 R1014 U1001 U1005 C1002 R1002 C1006 U1004 R1007 C1018 R1015 Q1001 R1016 R1026 R1025 R1024 R1023 R1022 R1021...

  • Page 71: Ir Board

    7.4 IR Board (715G5112R0C000004S) Remark: Parts position can be searched by using FIND function in PDF. ZD201 LED201 U201 CN201 7.5 Key Board (715G4719K01000004K) Remark: parts position can be searched by using FIND function in PDF. CN001 SW008 SW003 SW006...

  • Page 72: Wiring Diagram

    8. Wiring Diagram BDL3245E CN701 CNPC Board Panel Power Board CN902 CNPC Board CN901 CN901 CN413 CN422 CN416 CN405 CN414 CN415 CN420 CN6011 U401 Scaler Board CN4208 (OUT) (OUT) (OUT) (IN) (IN) IR Board CN201 CN001 Key Board...
  • Page 73 BDL4245E & BDL4645E Panel CN701 CNPC Board CN908 CN1005 CN906 CN1006 CN904 Power Board Connection Board CN905 CN413 CN422 CN104 CN405 CN414 CN415 CN416 CN907 10 60 12 1 CN420 U401 CN6011 Scaler Board CN4208 CN901 IR Board CN201 CN001 Key Board...

  • Page 74: Scaler Board Overview

    9. Scaler Board Overview FFC Connector Scaler IC CPLD Audio AMP VGA OUT VGA IN RJ-45 RS232C OUT/IN DVI-D IN HDMI IN AUDIO IN AUDIO OUT COMPONENT IN SPK OUT AUDIO IN VIDEO IN/OUT...

  • Page 75: Mechanical Instructions

    10. Mechanical Instructions BDL3245E Carefully place the TV monitor face down on a smooth surface. 1. Remove all the screws to remove the REAR_COVER Back.
  • Page 76 76 76 Remove all l the screws s to remove the bezel. 1) Remove e the BEZEL TOP, BEZEL L RIGHT and d BEZEL LEF 2) Remove e the BEZEL BOTTOM an nd BRACKET T_CHASS_W WALLMOUNT.
  • Page 77 3) Remove the key board from the BEZEL BOTTOM. 3. Remove the boards, speakers and FAN from the main frame 1) Remove the key board. 2) Disconnect all the connectors as follow: The reverse of the main frame The front of the panel...
  • Page 78 78 78 3) Remove all the screws as follow:...
  • Page 79 4. Remove the main frame from the panel...
  • Page 80 80 80 BDL4645E Note: the way of the BLD4245E disassembly is almost the same as the BDL4645E. Carefully place the TV monitor face down on a smooth surface. 1. Remove all the screws to remove the REAR_COVER Back.
  • Page 81 2. Remove all the screws to remove the bezel. 1) Remove the BEZEL TOP, BEZEL RIGHT and BEZEL LEFT. 2) Remove the BEZEL BOTTOM and BRACKET-CHASS_WALLMOUNT.
  • Page 82 82 82 3) Remove the key board from the BEZELBOTTOM 3. Remove the boards, speakers and FAN from the main frame 1) Remove the key board 2) Disconnect all the connectors as follow: The front of the panel...
  • Page 83 3) Remove all the screws as follow:...
  • Page 84 84 84 4. Remove the main frame from the panel...

  • Page 85: Trouble Shooting

    11. Trouble Shooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back 2. Make sure the power switch is of the display is not switched on. switched on.
  • Page 86 86 86 After-Images can still be A still picture is displayed for an over Do not allow a still image to be displayed seen on the display after extended period of time for an extended period of time as this the display is powered off.

  • Page 87: Isp Instruction

    2) Microsoft operation system Windows 95/98/2000/XP. 3) “GProbe 5.8.0.1.exe” program. 4) RS232C cablex1 5) Philips PD 2. Connecting the monitor to the PC 3. Prepare the F/W files. 1) Copy below three F/W files to one folder such as “batch”.
  • Page 88 88 88 2) Open the “ISP_MMD-OTS_MCU_V0.306_checksum.txt”; modify the “isp_spi_ext.hex” and “MMD_BDL4645E.hex” path to correct. 4. Install the ISP program “GProbe 5.8.0.1” to the PC 5. Firmware Upgrade Instruction 1) Double click the ISP software 2) Select “Options” → “Connection Setting”.
  • Page 89 3) Set the parameters as below figure...
  • Page 90 90 90 4) Type in “forcesa 10” and click “Execute” 5) When the state column becomes gray, AC on the Philips PD right now. It will pop up the “Command Successful” message. When it becomes gray, switch on the power supply...
  • Page 91 6) Click “Commands” — “batch” to load the file “isp_psi_ext.txt”.
  • Page 92 92 92 7) During the process which last about 4minutes, please don’t disconnect the cable and power. 8) Update successfully. The Burn in mode is turned on after F/W update.
  • Page 93 6. Check the version 1) Press “MENU” key → “Configuration2” → “Monitor information” → “version”. 2) Factory reset. 3) Usually F/W upgrade will turn on “Burn in” mode, while factory reset will turn off it.
  • Page 94 94 94 7. Troubleshooting. 1) Error executing batch file at line 7. The way to cure the error is to modify the “.hex” path correctly as steps3.2. 2) Failed to push the board into stand-alone mode error. a) The way to cure it is to AC off the PD and type in “forcesa 10” then click “Execute”. AC on the PD during the state column is gray.
  • Page 96 2) Microsoft operation system Windows 95/98/2000/XP. 3) USB Driver and ISP tool “MCU_ISP_SETUP_0.92.exe” program. 4) USB cablex1, VGA cablex1 5) ISP Board: 715GT183-A 6) Philips PD 2. Connecting the monitor to the PC 715GT183-A USB Cable 3. Installation of USB board driver.
  • Page 98 98 98 4. Installation of ISP tool. 1) Open the “MCU_ISP_SETUP_0.92” folder, click “Setup.exe” file to install. 2) After the installation of ISP tool and USB driver, restart the PC. 5. MCU F/W upgrade steps. 1) Open the ISP tool and click “ok” as below figures.
  • Page 99 2) Click “ ” to open the new window to set the relevant parameters. 3) Click “Exit & Save” after setting parameters. 4) Load correct software.
  • Page 100 5) Click “Auto” to upgrade. 6) Update processing.
  • Page 101 7) Upgrade successfully. 6. Troubleshooting. Not connected error. The way to cure it by select correct “ISP Target”...

  • Page 102: Ddc Instructions

    3. DDC In nstructio ote: Take the e BDL4645E E EDID SOP for example e (the BDL3 245E & BDL L4245E SOP P are almost t the same a DL4645E’s) eneral DC Data Re- programming case the ma ain EEPROM M with Softwa are DDC whic ch store all fa...
  • Page 103 13.3 The process of the DDC writing as follow: (Take the BDL4645E’s for example) Note: EDID files have been putted in DDC folder. DDC and EDID tool should be putted together. 1. Double-click the , appear as follow:...
  • Page 104 2. Tick the “Analog +DVI” and click “Loadfile” to set the parameters. 3. Select the EDID folder.
  • Page 105 4. Load EDID successful. In the EDID tool, you can know the EDID information. 5. Tick the “Only connect VGA”, and type in the 14 digit S/N which must be the same as the SN in barcode of set and date.
  • Page 106 6. Turn off the EDID write protect enable in factory mode. Turn on the PD and enter factory mode by pressing “[-] [-] [+] [+] [-] [+] [-] [-] [SET] [MEU]” keys in remote control. Don’t exit factory mode during EDID writing. 7.
  • Page 107 8. Press MEN key/Configuration2/monitor information/Monitor information. 13.4 Troubleshooting. 1. Can’t write error. 2. Try below few ways to cure can’t write errors! 1) Turn off the EDID write protect enable in factory mode. 2) AC on the monitor and turn on it.(Restart the monitor) 3) Set the Burn in on to try again.
  • Page 108 BDL3245E EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 11 D2 01 01 01 01 10| 21 15 01 03 68 46 27 78 2A 6E 4B A4 55 4A 9B 25 20| 0F 47 4A B5 28 80 81 00 81 80 D1 C0 A9 40 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 BA 89 21 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 109 640 x 480 @ 75Hz VESA 800 x 600 @ 60Hz VESA Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification: -> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz...
  • Page 110 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 11 D2 01 01 01 01 10| 24 15 01 03 80 46 27 78 2A 6E 4B A4 55 4A 9B 25 20| 0F 47 4A B5 28 80 81 00 81 80 D1 C0 01 01 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 BA 89 21 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 111 Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification :-> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz <-Detailed Timing Descriptions :->...
  • Page 112 00| 02 03 22 F1 4F 10 05 01 02 03 04 1F 13 11 12 14 10| 06 07 15 16 23 09 07 07 83 01 00 00 65 03 0C 00 20| 10 00 02 3A 80 18 71 38 2D 40 58 2C 45 00 BA 89 30| 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40| BA 89 21 00 00 18 01 1D 00 72 51 D0 1E 20 6E 28 50| 55 00 BA 89 21 00 00 1E 8C 0A D0 90 20 40 31 20...
  • Page 113 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification :-> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz <-Detailed Timing Descriptions :-> Detailed Timing: 1920x1080 @ 60Hz Detailed Timing: 1360x768 @ 60Hz FC (Monitor Name): PHL BDL3245E FD (Monitor Limits):...
  • Page 114 720 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 16:9 1280 x 720 P 59.94/60Hz 16:9 1920 x 1080 P 50Hz 16:9 1280 x 720 P 50Hz 16:9 720 x 576 P 50Hz 4:3 720 x 576 P 50Hz 16:9 1920 x 1080 I 50Hz 16:9 720(1440) x 480 I 59.94/60Hz 4:3 720(1440) x 480 I 59.94/60Hz 16:9...
  • Page 115 BDL4245E EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 12 D2 01 01 01 01 10| 24 15 01 03 68 5D 34 78 2A E6 9D A3 54 4A 99 26 20| 0F 47 4A B5 28 80 81 00 81 80 D1 C0 A9 40 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 A2 0B 32 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 116 800 x 600 @ 60Hz VESA Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification :-> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz 1600 x 1200 @ 60Hz...
  • Page 117 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 12 D2 01 01 01 01 10| 24 15 01 03 80 5D 34 78 2A E6 9D A3 54 4A 99 26 20| 0F 47 4A B5 28 80 81 00 81 80 D1 C0 01 01 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 A2 0B 32 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 118 Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification: -> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz <-Detailed Timing Descriptions: ->...
  • Page 119 --------------------Block 1-------------------- 00| 02 03 22 F1 4F 10 05 01 02 03 04 1F 13 11 12 14 10| 06 07 15 16 23 09 07 07 83 01 00 00 65 03 0C 00 20| 10 00 02 3A 80 18 71 38 2D 40 58 2C 45 00 A2 0B 30| 32 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40| A2 0B 32 00 00 18 01 1D 00 72 51 D0 1E 20 6E 28 50| 55 00 A2 0B 32 00 00 1E 8C 0A D0 90 20 40 31 20...
  • Page 120 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification :-> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz <-Detailed Timing Descriptions :->...
  • Page 121 640 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 16:9 1280 x 720 P 59.94/60Hz 16:9 1920 x 1080 P 50Hz 16:9 1280 x 720 P 50Hz 16:9 720 x 576 P 50Hz 4:3 720 x 576 P 50Hz 16:9 1920 x 1080 I 50Hz 16:9 720(1440) x 480 I 59.94/60Hz 4:3...
  • Page 122 OPS HDMI 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F --------------------Block 0-------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 12 D2 01 01 01 01 10| 24 15 01 03 80 5D 34 78 2A E6 9D A3 54 4A 99 26 20| 0F 47 4A B5 28 80 81 00 81 80 D1 C0 01 01 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 A2 0B 32 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 123 <-Established Timings :-> Established Timings 1:B5 720 x 400 @ 70Hz VGA, IBM 640 x 480 @ 60Hz VGA, IBM 640 x 480 @ 67Hz Apple, Mac II 640 x 480 @ 75Hz VESA 800 x 600 @ 60Hz VESA Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA...
  • Page 124 <-Video Short Block Description :-> 1920 x 1080 P 59.94/60Hz 16:9 1920 x 1080 I 59.94/60Hz 16:9 640 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 16:9 1280 x 720 P 59.94/60Hz 16:9 1920 x 1080 P 50Hz 16:9 1280 x 720 P 50Hz 16:9 720 x 576 P 50Hz 4:3...
  • Page 125 H Image Size: 930 mm V Image Size: 523 mm Pixel Clock: 27 Hz Refreshed Mode: Non-Interlaced Block1 Checksum: C9 BDL4645E EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 13 D2 01 01 01 01 10| 24 15 01 03 68 66 39 78 2A 26 0D A5 54 4A 9D 25 20| 0E 47 4A B5 28 80 81 00 81 80 D1 C0 A9 40 01 01...
  • Page 126 <-Established Timings :-> Established Timings 1:B5 720 x 400 @ 70Hz VGA, IBM 640 x 480 @ 60Hz VGA, IBM 640 x 480 @ 67Hz Apple, Mac II 640 x 480 @ 75Hz VESA 800 x 600 @ 60Hz VESA Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA...
  • Page 127 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 13 D2 01 01 01 01 10| 1B 15 01 03 80 66 39 78 2A 26 0D A5 54 4A 9D 25 20| 0E 47 4A B5 28 80 81 00 81 80 D1 C0 01 01 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 FA 3D 32 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 128 Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II 1024 x 768 @ 60Hz VESA Established Timings 3:80 1152 x 870 @75Hz Apple, Mac II <-Standard Timing Identification :-> 1280 x 800 @ 60Hz 1280 x 1024 @ 60Hz 1920 x 1080 @ 60Hz <-Detailed Timing Descriptions :->...
  • Page 129 HDMI 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F --------------------Block 0-------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 13 D2 01 01 01 01 10| 24 15 01 03 80 66 39 78 2A 26 0D A5 54 4A 9D 25 20| 0E 47 4A B5 28 80 81 00 81 80 D1 C0 01 01 01 01 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 FA 3D 32 00 00 1E 66 21 50 B0 51 00 1B 30...
  • Page 130 Ry: 0.330 Gy: 0.615 By: 0.055 Wy: 0.290 <-Established Timings :-> Established Timings 1:B5 720 x 400 @ 70Hz VGA, IBM 640 x 480 @ 60Hz VGA, IBM 640 x 480 @ 67Hz Apple, Mac II 640 x 480 @ 75Hz VESA 800 x 600 @ 60Hz VESA Established Timings 2:28 832 x 624 @ 75Hz Apple, Mac II...
  • Page 131 Extended Block Type: CEA 861B Detailed Timing Blocks start at Byte: 22 DTV Underscan YES DTV Basic Audio YES YCbCr (4:4:4) YES YCbCr (4:2:2) YES <-Video Short Block Description :-> 1920 x 1080 P 59.94/60Hz 16:9 1920 x 1080 I 59.94/60Hz 16:9 640 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 16:9...
  • Page 132 Pixel Clock: 27 Hz Refreshed Mode: Non-Interlaced Detailed Timing Descriptions: 1280x720 @ 60Hz H Image Size: 1018 mm V Image Size: 573 mm Pixel Clock: 74 Hz Refreshed Mode: Non-Interlaced Detailed Timing Descriptions: 720x576 @ 50Hz H Image Size: 1018 mm V Image Size: 573 mm Pixel Clock: 27 Hz Refreshed Mode: Non-Interlaced...
  • Page 133 Week of Manufacture: Year of Manufacture: 2011 <-Basic Display Parameters/Features :-> Video i/p definition: Digital Max. H. Image Size: 102cm Max. V. Image Size: 57cm Display Gamma: <-Color Characteristics :-> Rx: 0.645 Gx: 0.289 Bx: 0.145 Wx: 0.279 Ry: 0.330 Gy: 0.615 By: 0.055 Wy: 0.290...
  • Page 134 Max. V. rate: 85 Hz Min. H. rate: 28 KHz Max. H. rate: 92 KHz Max. P Clock: 170 MHz Extension Flag: 01 Block0 Checksum: ED ------------------------------------------------------- Block 1: Extended Block Type: CEA 861B Detailed Timing Blocks start at Byte: 22 DTV Underscan YES DTV Basic Audio YES YCbCr (4:4:4) YES...
  • Page 135 <-Speaker Allocation :-> Speaker Allocation: FL/FR <-Detailed Timing Descriptions: -> Detailed Timing Descriptions: 1920x1080 @ 60Hz H Image Size: 1018 mm V Image Size: 573 mm Pixel Clock: 148 Hz Refreshed Mode: Non-Interlaced Detailed Timing Descriptions: 720x480 @ 60Hz H Image Size: 1018 mm V Image Size: 573 mm Pixel Clock: 27 Hz Refreshed Mode: Non-Interlaced...

  • Page 136: White Balance, Luminance Adjustment

    14. White Balance, Luminance Adjustment Equipment: PC x 1, Chroma2325 (or equivalent instrument), CA-210 x 1, W/B record card x 1 Equipment installation: 1. Connect analyzer CA-210 to PC by USB connector, install driver program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing 2.

  • Page 138: Monitor Exploded View

    15. Monitor Exploded View...

  • Page 141: Recommended & Spare Parts List

    16. Recommended & Spare Parts List Note: the parts information listed below are for reference only, and are subject to change without notice. Please go http://cs.tpv.com.cn/hello1.asp for the latest information Recommended Parts list for BDL4245E/00 Item Location PCM Codes Description Remark FQ106 A34J2702BET 1T0100...
  • Page 142 100GPDAM002N11 PHILIPS BDL4245E(056G2233 34) U459 100GPDAM003N11 PHILIPS BDL4245E(056G1125199) U402 100GPDAM004N11 PHILIPS BDL4245E(056G 665172) U412 100GPDAM005N11 PHILIPS BDL4245E(056G 777 22) U607 100GPDAM006N11 PHILIPS BDL4245E(056G1133158) X402 093G 22 61 HE XTL 1TC125DFNS004 32.768KHZ DT-38 X404 093G 22513 YC CRYSTAL 12MHZ/20PF/49US 30PPM X401 093G 22905 H CRYSTAL 19.6608MHZ 20P AT-49...
  • Page 143 IC9801 056G 379165 AC/DC CONVERTER R2A20117CSP SOP16 IC9101 056G 379176 IC SSC9512S-TL SOP-18 IC9901 056G 665532 Capacitor Discharge CAP014DG-TL SOP-8 Service Kit Description Part No. Picture ISP tool 715GT183-A DDC TOOL 715GT034-B...

  • Page 144: General Product Specification

    17. General Product Specification Please refer to the Product Specification the next page:...

  • Page 145: Product Identification

    BDL LCD DISPLAY BDLxx45E/00 Issued by: Technical Marketing Manager Larry Yang CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 1 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 146 5.3.2 Timing between each message should be a minimum of 500 ms ............. 26 5.3.3 There should be a menu selection ..................... 26 5.3.4 Philips SICP codes must be supported....................26 ACCESSORIES .............................. 27 ..............................27 ABLES ........................... 27...
  • Page 147 Verification of ECN......................... 38 10.8.7 Update the deliverables list ......................38 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 3 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 148: Scope

    YY: Year (2009: 09, 2010:10) • WW: Week • XXXXXX: 000001~999999 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 4 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 149: General Product Features

    • Support components video input, audio input and audio output. • Support HDMI Ver.1.3b. with HDCP, audio included (meet EIA-861B standard) • User-friendly and family look OSD menu (follow Philips OneUX design) • User-friendly and professional look remote controller • DPM power management for PC mode •...

  • Page 150: Electrical Requirements

    Timing Table for MMD Projects_20110 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 6 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 151: Av Input Signal Requirements

    1920x1080 @ 50 and 60Hz interlaced (“1080i”) The HDMI input supports copy protection (HDCP). CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 7 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 152: Ddc Channel

    The DDC/CI commands should be compliant to Smart Control utility CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 8 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 153: Service Mode

    CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 9 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 154 Power ON, Input signal Line2 to GND ±2kV Power ON, Input signal CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 10 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 155: User Control Interface

    VOLUME +/-: Change Volume or navigate through OSD depending on mode. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 11 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 156: Front Controls

    ≥ 5m (control from the front) 20° (for H & V) ≥ 2m (control from the front) 45° (for H only) • Remote Control – Philips protocol. Philips protocol is used for remote control communication. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS...
  • Page 157 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 13 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 158 To increase the audio output level. VOL DOWN button To decrease the audio output level. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 14 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 159: Osd Menu

    Please refer to the latest Philips designs and templates RC key definition: Remote Key Key Name Data Code POWER 0x03 VIDEO SOURCE 0x01 AUDIO SOURCE 0x1E SMART 0x1D SIZE 0x29 PIP ON/OFF 0x24 PIP INPUT 0x25 PIP CHANGE 0x26 CONTRAST...

  • Page 160: I/O Connectors

    21 N/A TMDS clock shield CLASS NO. 23 TMDS clock+ TMDS clock– BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 16 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 161 Received Line Signal Detector (Carrier Detect) DTE-to-DCE Data Terminal Ready DCE-to-DTE Ring Indicator CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 17 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 162: Visual Performance

    View Angle (CR > 10) up/down:89(min) Power Consumption 105W(type);115W(max) Module Weight 5.5Kg(Typ);6.9Kg(max) CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 18 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 163 120W(type);126W(max) Module Weight 11.5Kg(Typ) Panel flicker depend on panel supplier CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 19 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 164: Front Of Screen Performance

    Contouring - Minimum contouring visible. Blue stretch - Green enhance - CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 20 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 165: Functional Requirements

    CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 21 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 166: Picture In Graphics

    User can define the time interval (10~900 seconds) to run this feature Off mode: Don’t execute the burn-in prevention program. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 22 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 167: Pc Picture Auto Adjustment Function

    The existing daylight on/off menu item should be replaced with the following menu structure: CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 23 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 168: Auto Signal Switching And Detecting

    Turn on OPS automatically, then show "Card OPS is Turned On" in OSD. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 24 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 169 Do normal power saving. B. ON: Turn off panel only. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 25 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 170: Non Functional Requirements

    5.3.3 There should be a menu selection ( e.g. in the service menu) for the baud rate of 1200,2400, 4800,9600, 19200, 57600, 115200 5.3.4 Philips SICP codes must be supported. The SICP Commands Document V1.6_2011 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY...

  • Page 171: Accessories

    French / Italian / Russian / Polish Turkish /Simplified Chinese. Warranty card CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 27 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 172: Others

    Painting to cover up cosmetic defects due to molding is strongly discouraged. No plastic mold tooling CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 28 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 173: Plastics Flammability

    All major plastic parts (bezel, back cover, base) need to be molded from same resin. Base / Pedestal otherwise specified. 7.10 Texture/Glossing of Housing • The texture area and texture no should follow Philips make-up sheet. • The exterior surfaces shall have a uniform texture. • Philips must approve the mold texturing.

  • Page 174: Product Dimension / Weight

    Multiple drop test only for China & India(UAN-D 1534/02) • Bump test only for China & India(UAN-D 1534/02) CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 30 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 175: Pallet / Container Loading

    -20 to 60 ºC • Shipping - -20 to 60 ºC CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 31 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 176: Humidity

    Directive 2004/108/EC EN55022:2006+A1:2007 EMC/CE test EN55024:1998+A1:2001+A2:2003, Supplier report EN61000-3-2:2006, EN61000-3-3:1995+A1:2001+A2:2005 EN55020 CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 32 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 177 China SJ/T 11364-2006 Supplier EPA5.0 Annex 2 ENERGY STAR Supplier CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 33 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 178: Emc Requirements

    Restriction on the use of certain hazardous substances. Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and Polybrominated Bipheny1 Ether (PBDE)(flame retardant). WEEE Producer (Philips) responsible for retailer take back schemes and recycling. -- System implemented. -- Collection and recycle targets. Ongoing Regulatory There's a possibility that other regulatory certificates will be required during the life of the product.

  • Page 179: System Flow Chart

    MMD. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 35 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 180: Quality And Reliability Deliverables List

    Tiling Set 0x22 Compatibility Test Party HDMI/PC Test: Allion Test Lab CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 36 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 181: Design Quality And Reliability Review And Validation Procedure

    The third party must be approved by MMD. CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 37 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...

  • Page 182: 2011-07-01 Philips

    10.8.5 Review issue technical report 10.8.6 Verification of ECN 10.8.7 Update the deliverables list CLASS NO. BDL3245E/BDL4245E/BDL4645E 32”/42”/46” FHD LCD PUBLIC DISPLAY 2011-07-01 PHILIPS Page 38 of 38 NAME SUPERS. PHILIPS ELECTRONICS INDUSTRIES (TAIWAN) LTD.-C.E. CHECK DATE Property of MMD Confidential 2838 100 05424...
  • Page 183 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.

This manual is also suitable for:

Bdl4245e/00Bdl4645e/00

Table of Contents