Advertisement
DM-S500
Note: Numerals on the display appear the error rate and
ADIP error.
3. Terminating the continuous playback mode
(1) Press the STOP key. The display then changes to
"CPLAY MODE".
(2) Press the EJECT key to take out the disc.
Note : The playback start addresses of IN, MID, and OUT
are described below.
IN
30H cluster
MID
300H cluster
OUT
700H cluster
2-4-2 Operation in continuous recording mode
1. Entering the continuous recording mode
(1) Insert a recordable disc into the unit.
(2) Turn the SHUTTLE to display "CREC MODE".
(3) Press the PLAY key. The display then changes from
"CREC MODE" to "CREC MID".
(4) Press the PLAY key again. The display changes from
"CREC MID" to "CREC (####)", and the continuous
recording is started.
Note : Numerals on the display (####) appear the address
of recording point.
2. Change the recording point.
(1) Turn the SHUTTLE to clockwise while "CREC MID" is
displayed. The display changes as follows. (The record-
ing point can be shifted.)
MID
OUT
(2) Press the ENTER key. The display then changes to
"CREC(####)", and the continuous recording is started.
Note : Numerals on the display (####) appear the address
of recording point.
3. Terminating the continuous recording mode
(1) Press the STOP key. The display then changes to
"CREC MODE" and the REC display goes off.
(2) Press the EJECT key to take out the disc.
Notes :
1. The recording start addresses of IN, MID, and OUT are
described below.
IN
30H cluster
MID
300H cluster
OUT
700H cluster
2. The STOP key can be pressed at any time to stop the
recording.
3. An erasure prevention control is not detected in the test
mode. Be careful not to enter the continuous recording
mode using a disc containing the data that should not be
erased.
4. Do not record continuously for more than five minutes.
5. Take care that no vibration is applied during continuous
recording.
ADJUSTMENT
IN
2-5 Other key function
Function
3
Plays back continuously when this key is pressed during
stop. Turn on and off the tracking servo when it is
pressed during continuous playback.
7
Stops the continuous playback and recording.
1
The thread moves to the inner circumference while this key
is pressed.
¡
The thread moves to the outer circumference while this
key is pressed.
Note : An erasure prevention control is not detected in the
test mode. Notice that recording is performed irrespective
of the erasure prevention control position when the REC key
is pressed.
2-6 Precaution on use of test mode
An erasure prevention control is not detected in the test
mode. Therefore, when the recording laser power mode
such as continuous recording mode and traverse adjust-
ment mode is entered, the contents of the existing
recording are erased irrespective of the control position.
Be careful not to enter the continuous recording mode
and traverse adjustment mode when using a disc, con-
taining the data that should not be erased, in the test
mode.
3. Electrical adjustment
3-1 Precaution during confirmation of Laser Diode
emission
During adjustment, do not view the emission of a laser diode
from just above for confirmation. This may damage your
eyes.
3-2 Precaution on handling of Optical pick-up
(KMS-260A)
The laser diode in an optical pick-up is easy to be subject to
electrostatic destruction. Therefore, solder-bridge the laser
tap on the flexible board when handling the optical pick-up.
When removing the flexible board from the connector, make
a solder bridge in advance, then remove the board. Be
careful not to remove the solder bridge before inserting the
connector. Moreover, take careful measures against elec-
trostatic destruction. The flexible board is cut easily. Han-
dle the flexible board with care.
Pick-up
3-3 Precaution during adjustment
1) Perform the adjustment and confirmation marked with
"O" in the order shown in the table when the parts below
are replaced.
Description
Flexible board
Laser tap
6
Advertisement
