Related Manuals for Panasonic PT-D6000K
Summary of Contents for Panasonic PT-D6000K
- Page 1 PT-D6000S/D6000K P ro d u c t N u m b e r : PT-D6000LS/D6000LK P ro d u c t N a m e : As of February 2009. Specifications subject to change without notice. The PT-D6000LS and PT-D6000LK are not equipped with a lens. ™...
- Page 2 PT-D6000S/D6000K/D6000LS/D6000LK ™ Projectors Specifications Main Unit Power supply: North America: Europe: Power consumption: North America: Europe: DLP™ chip: Panel size: Display method: Pixels: Lens: PT-D6000S/D6000K: PT-D6000LS/D6000LK: Lamp: Screen size: Brightness* Center-to-corner uniformity* Contrast* Resolution: Scanning frequency: DVI-D: RGB: S-Video/Video: Optical axis shift: Keystone correction range: Installation: Terminals *...
- Page 3 PT-D6000S/D6000K/D6000LS/D6000LK ™ Projectors RGB 2 IN: R, G, B: Y, P VIDEO IN: S-VIDEO IN: SERIAL IN: SERIAL OUT: REMOTE 1 IN: REMOTE 1 OUT: REMOTE 2 IN: LAN: Power cord length: Cabinet materials: Dimensions (W x H x D): PT-D6000S/D6000K: PT-D6000LS/D6000LK: Weight: PT-D6000S/D6000K:...
- Page 4 PT-D6000S/D6000K/D6000LS/D6000LK ™ Projectors Dimensions Terminals SYNC/HD S-VIDEO IN VIDEO IN RGB1 IN SERIAL REMOTE 1 REMOTE 2 As of February 2009 416 (16-3/8˝) 498 (19-19/32˝) Video input S-Video input RGB 1 input RGB2 IN DVI-D I N RGB 2 Input DVI-D input LAN connector unit : mm (inch)
- Page 5 PT-D6000S/D6000K/D6000LS/D6000LK ™ Projectors Standard setting-up position (when installed using the ET-PKD56H) Upper edge of projected image Projected image Lower edge of projected image Projected image C A U T I O N The ET-DLE055 has a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used.
- Page 6 PT-D6000S/D6000K/D6000LS/D6000LK ™ Projectors Projection distance for 4:3 aspect ratio screen Screen size (inch, diagonal) ET-DLE150 Supplied lens Zoom lens min. max. min. max. 1,344 1,967 1,785 2,376 1,623 2,370 2,155 2,864 1,903 2,773 2,525 3,352 2,183 3,177 2,895 3,840 2,462 3,580 3,265 4,328...
- Page 7 • Floor mount (Width of projected image) 0.1H Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of 360°. As of February 2009 L (mm) = (diagonal screen size in inches) x 28.0 - 54.0 L (mm) = (diagonal screen size in inches) x 40.3 - 49.8...
- Page 8 NOTE: The native resolution of this projector is 1,024 x 800 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
- Page 9 • It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. • When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.
- Page 10 * Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. * When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply. As of February 2009...
- Page 11 Command : Parameter Function Main power status Shutter function status Freeze function status Input signal status On-screen display status Projector run time Q$L:1 Lamp 1 run time Q$L:2 Lamp 2 run time Lamp operation mode status Lamp power mode status...
- Page 12 * Even when the ambient temperature near the intake opening is 40°C/104°F or lower, an accumulation of hot air inside the cabinet may cause the protective circuit to activate and shut down the projector. Please give ample consideration to the design with regard to ambient temperature conditions.