1 MΩ and 5.2 MΩ. When the exposed metal does not have a return path to the chassis, the reading must be infinity. Downloaded From CamcorderManual.com Panasonic Manuals...
(an equivalent type of resistor may be used.) 3. Put the resistor between both terminals of capacitor on FRONT PCB for approx. 5 seconds. 4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter. Fig. F1 Downloaded From CamcorderManual.com Panasonic Manuals...
(ESD) suf- ficient to damage an ES device). 2.2. How to Recycle the Lithium Ion Battery (U.S. Only) Downloaded From CamcorderManual.com Panasonic Manuals...
13-ampere socket. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician. 2. Replace the fuse and attach the Fuse cover. Downloaded From CamcorderManual.com Panasonic Manuals...
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration. Downloaded From CamcorderManual.com Panasonic Manuals...
Page 8
NOTE: Above caution is applicable for a battery pack which is for SDR-S100 series, as well. Downloaded From CamcorderManual.com Panasonic Manuals...
Schematic diagram, Block Diagram and PCB layout of Main PCB (L), (R). b. Parts list for individual parts of Main PCB (L), (R). When a part replacement is required for repairing Main PCB (L), (R), replace as an assembled parts. (Main PCB (L), (R)) Downloaded From CamcorderManual.com Panasonic Manuals...
NOTE: After replacing the MAIN PCB (L), (R), be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in “TSN system”, together with Maintenance software. Downloaded From CamcorderManual.com Panasonic Manuals...
Do not using service mode except [ 1 ], [ 3 ] of Service Menu. 3. End method of the top screen of the service menu Top screen of the service menu is finished by POWER OFF. Downloaded From CamcorderManual.com Panasonic Manuals...
• The error cord contents which are displayed Error code Function Zoom control is abnormal Focus control is abnormal OIS lens control is abnormal Lens cover open/close is abnormal Lock search history indication is finished by POWER OFF. Downloaded From CamcorderManual.com Panasonic Manuals...
Page 18
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2. Be careful of the high voltage circuit on FRONT PCB. 3. DO NOT allow other parts to touch the high voltage circuit on FRONT PCB. Downloaded From CamcorderManual.com Panasonic Manuals...
LCD Hinge Unit 3 Ribs 1 Rib Fig. D45 Iris Unit Monitor PCB Zoom Motor Unit Fig. D46 2 Screws (e) Zoom Motor Unit Focus Motor Unit Fig. D47 2 Screws (f) Focus Motor Unit Downloaded From CamcorderManual.com Panasonic Manuals...
Page 21
4th Lens Frame Move Unit Fig. D49 NOTE (When Installing) OIS Unit Fig. D50 OIS Unit 2nd Lens Frame Move Fig. D51 2nd Lens Frame Move Unit Unit, Guide Pole 2 Guide Poles Fig. D1 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 22
8.3.2. Removal of the Side Case (R) Unit Fig. D4 Fig. D2 Fig. D3 Fig. D5 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 23
8.3.3. Removal of the Side Case (L) Cover 8.3.4. Removal of the Front Case Unit Unit Fig. D6 Fig. D9 Fig. D7 Fig. D10 Fig. D8 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 24
Fig. D13 Fig. D11 8.3.5. Removal of the Rear Case Unit Fig. D14 8.3.6. Removal of the Top Case Unit Fig. D12 Fig. D15 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 25
8.3.8. Removal of the Lens Unit Fig. D16 Fig. D19 8.3.7. Removal of the Main (R) PCB 8.3.9. Removal of the Main (L) PCB Fig. D17 Fig. D20 Fig. D18 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 26
8.3.10. Removal of the Front PCB Fig. D23 Fig. D21 8.3.11. Removal of the LCD Unit Fig. D22 Fig. D24 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 27
8.3.12. Removal of the Monitor PCB 8.3.13. Removal of the LCD Fig. D25 Fig. D27 Fig. D26 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 28
Fig. D30 Fig. D31 Fig. D28 8.3.14. Removal of the SD Cover, SD Cover Detection Knob and SD Cover Detection Spring Fig. D32 Fig. D29 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 29
8.3.15. Removal of the Mic PCB Fig. D35 Fig. D33 8.3.16. Removal of the ECM Flex Unit and Flash Unit Fig. D36 Fig. D34 Fig. D37 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 30
8.3.18. Removal of the Barrier Motor Unit Fig. D38 8.3.17. Removal of the Rear Case and Rear Operation Unit Fig. D41 Fig. D39 Fig. D42 Fig. D40 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 31
8.3.19. Removal of the Prism Unit and Optical Filter Fig. D45 8.3.21. Removal of the Zoom Motor Unit Fig. D43 8.3.20. Removal of the Iris Unit Fig. D44 Fig. D46 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 32
8.3.22. Removal of the Focus Motor Unit Fig. D47 8.3.23. Removal of the Master Flange and 4th Lens Frame Move Unit Fig. D49 8.3.24. Removal of the OIS Unit Fig. D48 Fig. D50 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 33
8.3.25. Removal of the 2nd Lens Frame Move Unit and Guide Pole Fig. D51 Downloaded From CamcorderManual.com Panasonic Manuals...
• Connection method of the main unit and an exclusive adjustment jig as follows Figure of connection • Install the EVR jig to PS6002 of Main PCB (L). (Refer to the disassembly procedure) Figure of image when adjustment Downloaded From CamcorderManual.com Panasonic Manuals...
Page 35
• Only a necessary jig mentions it in setup of electric adjustment. Part Name Part Number Remarks ------ 232C Dsub 9 pin I/F Cable VFK1395 EVR Adjustment Board VFK1983 20 pin Cable VFK1712 EVR Connection Board VFK1853EVR EVR Connection Adaptor VFK1984 Downloaded From CamcorderManual.com Panasonic Manuals...
(Setting the folder number is 100, and file number is 0.) 4. Clear the mechanism lock information. 5. Clear the service mode information contents. The setting position of factory settings: Name Setting position Power switch Mode select switch AUTO Mode dial Motion picture recording mode Downloaded From CamcorderManual.com Panasonic Manuals...
Page 37
S4.2. Monitor Schematic Diagram ..........S-5 S7.3. Lens Section ............... S-26 S4.3. Mic-IR Schematic Diagram ........... S-6 S7.4. Packing Parts and Accessories Section ......S-27 S4.4. Front Schematic Diagram ............. S-7 S4.5. CCD-FPC Schematic Diagram..........S-8 Downloaded From CamcorderManual.com Panasonic Manuals...
(FOIL SIDE) D GND M WIDE D GND M DSD Y SENS M DSD YREF M CKH1 REGD3V M CKH2 ECM (L/R) LED LANK BL CONT SDR-S100 M LED5V OPEN/CLOSE FP902 INTERCONNECTIONDIAGRAM DET. SW ECM PCB Downloaded From CamcorderManual.com Panasonic Manuals...
4. The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. E.S.D. standards for Electrostatically Sensitive Devices, refer to “PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES” section. S-19 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 56
S-20 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 57
S-21 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 58
S-22 Downloaded From CamcorderManual.com Panasonic Manuals...
Page 59
S-23 Downloaded From CamcorderManual.com Panasonic Manuals...